2011 Seat Altea lights

If and when
266
For the sake of the environmentIf you have to dispose of a sealant can, go to a specialised waste service or to
a SEAT Technical Service, where the product can be recycled in an appropriate
waste container.
Note
•If sealant should leak out, leave it to dry. This way you can pull it off like a
piece of foil.•Observe the expiry date stated on the sealing compound can. Have the
sealing compound exchanged by a specialised workshop.•Seek professional assistance if the repair of a tyre puncture is not
possible with the sealing compound.Preparation work
Certain steps must be taken before repairing a tyre.– If you have a flat tyre or puncture, park the vehicle as far away from the flow of traffic as possible.
–Apply the handbrake firmly.
–Engage first gear, or put the selector lever to position P.
– All passengers should leave the vehicle. They should wait in a
safe area (for instance behind the roadside crash barrier).
– Check whether a repair is possible using the Tyre Mobility System “General information and safety notes.”
– Unscrew inflation cap from the affected wheel. –Take the
tyre repair kit out of the luggage compartment.
WARNING
Put the hazard warning lights on and place the warning triangle in position.
This is for your own safety and also warns other road users.
Caution
Take special care if you have to repair a tyre on a slope.
Note
Please observe legal requirements when doing so.Tyre repair
The following sections describe the procedures for repairing
a tyre.Using the sealing compound
– The instructions on the container give detailed information on
how to use the sealing compound.
Inflating the tyre.
– Remove the air compressor and hose from the container.
– Screw the retaining nut onto the valve.
– Plug the compressor cable into a 12 volt power point.
Altea_EN.book Seite 266 Donnerstag, 2. September 2010 2:00 14

If and when
272
Bulb changeGeneral notesBefore changing any bulb, first turn off the failed component.
Do not touch the bulb glass. Fingerprints vaporise in the heat, causing a
reduction in the bulb life and condensation on the mirror surface, thus
reducing efficiency.
A bulb should only be replaced by one of the same type. The type is inscribed
on the bulb, either on the glass part or on the base.
It is highly recommended to keep a box of spare bulbs in the vehicle. At the
very least, the following spare bulbs, which are essential for road safety,
should be kept in the vehicle.
Main headlights
Dipped beam - H7
Main beam - H1
Position - W5W
Turn signal - PY21W
Xenon headlights
26)/adaptive*
Dipped and full beam - D1S
27)
Daylight - P21W SLL
Position W5W
Turn signals PY21W
15
Engine management
5
Pump relay
10
16
Right lighting
30
17
Horn
15
18
Vacan t
19
Clean
30
20
Water pump
10
Pressure sensor pump for 1.8 engine
20
21a)
Lambda probe
15
22
Brake pedal, speed sensor
5
23a)
Engine management
5
Engine management
10
Engine management
15
24
AKF, gearbox valve
10
25a)
ABS pump
40
26
Left lighting
30
27a)
Engine management
40
Engine management
50
28
Vacan t
29a)
Electric windows (front and back)
50
Electric windows (front)
30
30
Ignition key
50
a)Ampere rating according to motorisationNumber
Consumer
Amps
26)On this type of headlight, the bulb changes must be made by the SEAT dealer, given
that complex elements must be removed from the vehicle and a reset must be made
on the automatic control system incorporated.27)The Xenon bulbs discharge 2.5 times the light flux and have an average lifespan of 5
times more than that of halogen bulbs, this means that, except due to unusual circum-
stances, there is no need to change the bulbs for the whole life of the vehicle.
Altea_EN.book Seite 272 Donnerstag, 2. September 2010 2:00 14

If and when273
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Fog lights
Fog lights - H3
Upper tail light
Stop/Position - P21W
28)
Turn signal - R10W
Lower tail light
Fog light - P21W
Reverse light - P21W
Side turn signal
Side turn signal - W5W
Number plate light
Number plate light - C5W
Note
•Depending on weather conditions (cold or wet), the front lights, the fog
lights, the tail lights and the turn signals may be temporarily misted. This has
no influence on the useful life of the lighting system. By switching on the
lights, the area through which the beam of light is projected will quickly be
demisted. However, the edges may continue to be misted.•Please check at regular intervals that all lighting (especially the exterior
lighting) on your vehicle is functioning pr operly. This is not only in the interest
of your own safety, but also that of all other road users.•Due to the difficulty in accessing some of the bulbs, any replacement work
should be done by a SEAT dealer. However, the following is a description of
how to change the lamps except for the fog lights* and interior lamps.
Main headlight bulbs
Turn signal
Dipped beam headlights
Main beam headlights
Side lights
28)Electronically controlled single filament bulb for Stop/side bulbs. If the bulb blows it
will not work in either position or Stop.
Fig. 183 Main headlight
bulbs
AAABACAD
Altea_EN.book Seite 273 Donnerstag, 2. September 2010 2:00 14

If and when
274Turn signal bulbs– Raise the bonnet.
– Rotate the bulb holder ⇒fig. 184 to the left and pull.
– Remove the bulb by pressing on the bulb holder and rotating at the same time to the left.
– Installation is done in the reverse order.
Dipped beam headlights– Raise the bonnet.
Fig. 184 Turn signal
AA
Fig. 185 Dipped beam
headlightsFig. 186 Dipped beam
headlights
Altea_EN.book Seite 274 Donnerstag, 2. September 2010 2:00 14

If and when275
Safety First
Operating Instructions
Practical Tips
Technical Specifications
– Remove the loops ⇒page 274, fig. 185 in the direction of
the arrow and remove the cover.
– Remove the connector ⇒page 274, fig. 186 from the bulb.
– Unclip the retainer spring ⇒page 274, fig. 186 pressing
inwards to the right.
– Extract the bulb and fit the replacement so that the rim of the attachment plate is on the reflector cut-out.Main beam headlights
– Raise the bonnet.
– Remove the cover ⇒fig. 187 by pulling on this.
– Remove the connector ⇒fig. 188 from the bulb.
– Press the spring ⇒fig. 188 inwards and to the right.
– Extract the bulb and fit the replacement so that it sits correctly into the cut-out on the reflector.
– Installation is done in the reverse order.
A1
A2A3
Fig. 187 Main beam
headlights
Fig. 188 Main beam
headlights
AC
A1
A2
Altea_EN.book Seite 275 Donnerstag, 2. September 2010 2:00 14

If and when
276Side lights– Raise the bonnet.
– Remove the cover ⇒fig. 189 by pulling on this. – Extract the bulb holder
⇒fig. 190 outwards.
– Replace the bulb by pulling it out and inserting the replacement.
– Installation is done in the reverse order.
Ta i l l i g h t s•Side lights•Brake lights•Turn signals•Reverse lights•Rear fog light
Fig. 189 Side lightsFig. 190 Side lights
AD
A1
Altea_EN.book Seite 276 Donnerstag, 2. September 2010 2:00 14

If and when277
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Side lights and brake lights–Open the tailgate.
– Remove the bolts ⇒fig. 191 . – Remove the cover of the luggage compartment lateral panel.
– Unscrew the plastic fitting
⇒fig. 192 securing the tail light.
Inserting a screwdriver under th e plastic fitting may help to
loosen it.
– Partially remove the tail light from its casing taking care not to pull on the cable.
– Remove the bulb holder connector.
–Unscrew the bolts ⇒ page 278, fig. 193 from the bulb holder
and pull on this.
– Press on the bulb and rotate to the left then fit the replacement.
– To refit follow the steps in reverse order, taking special care when fitting the bulb holder. The metal contacts of the bulb holder
ends should be correctly fitted with respect to the tail light
contacts.
Fig. 191 Side lights and
brake lightsFig. 192 Side lights and
brake lights
AA
ABAC
Altea_EN.book Seite 277 Donnerstag, 2. September 2010 2:00 14

If and when279
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Side turn signals– Press the turn signal to the left or to the right to remove the bulb.
– Remove the bulb holder from the turn signal.
– Remove the failed glass bulb and replace with a new bulb.
– Insert the bulb holder in the turn signal guide until it clicks into
place.
– First place the turn signal in the opening in the bodywork, fixing the tabs ⇒ fig. 196, arrow .
– Insert the bulb as shown by the arrow ⇒fig. 196 .
Luggage compartment lights– Remove the bulb by pressing on the inside edge of this -arrow-
using the flat side of a screwdriver ⇒fig. 197 .
Fig. 196 Side turn signal
A1
A2
Fig. 197 Luggage
compartment lightFig. 198 Luggage
compartment light
Altea_EN.book Seite 279 Donnerstag, 2. September 2010 2:00 14