2011 RENAULT SCENIC brake

13B-132
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DDCR INJECTION
Vdiag No.: 44, 48
ET415
CONTINUED 1
STATUS 2
Brake pedal depressed
The cruise control function is deactivated when the brake pedal is depressed.
Status ET415 becomes STATUS 2 when driving with cruise control active
(ET042 Cruise control - speed limiter: CRUISE CONTROL) and the brake pedal is
depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If status ET415 becomes STATUS 2 without pressing the brake pedal, consult
the interpretation of statuses ET704 and ET705 Brake contact No. 1 and No. 2.
STATUS 3Clutch pedal depressed
Manual gearbox ONLY
The cruise control function is deactivated when the gearbox is not coupled to
the engine (clutch pedal depressed).
Status ET415 becomes STATUS 3 when driving with the cruise control active
(ET042 Cruise control - speed limiter: CRUISE CONTROL) and the clutch pedal
is depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If status ET415 becomes STATUS 3 without the clutch pedal being depressed,
consult the interpretation of status ET405 Clutch pedal.
If the vehicle is fitted with automatic transmission:
Test the multiplex network: check the configuration of the multiplex network in relation
to the vehicle's technical specification, especially the configuration of the automatic
transmission computer (see 88B, MULTIPLEXING).

13B-134
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DDCR INJECTION
Vdiag No.: 44, 48
ET415
CONTINUED 3
STATUS 5
Cruise control or speed limiter monitoring
This status appears when the vehicle brakes or decelerates sharply without
the injection computer receiving a signal that the brake pedal switch has been
pressed.
If status ET415 is STATUS 5, consult the interpretation:
– of status ET042 Cruise control/Speed limiter,
– of status ET703 Cruise control - speed limiter buttons,
– of status ET704 Brake switch no. 1,
– and status ET705 Brake switch no. 2,
to test the cruise control/speed limiter system components and locate the faulty
component.
Also, check the operation of the accelerator pedal, and use the diagnostic tool to
check the presence of a fault connected with this component. Deal with them if
necessary.
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If status ET415 becomes STATUS 5, deal with the present faults or those stored in
the injection computer.
If the fault is still present, contact the Techline.

13B-141
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DDCR INJECTION
Vdiag No.: 44, 48
ET704
ET705BRAKE SWITCH NO. 1
BRAKE SWITCH NO. 2
NOTESNone.
Note:
Statuses ET704 and ET705 should change status at the same time. In the event of inconsistency, refer to
the interpretation of fault DF050 Brake switch circuit.
DDCR_V44_ET704/DDCR_V48_ET704 / DDCR_V44_ET705/DDCR_V48_ET705

13B-142
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DDCR INJECTION
Vdiag No.: 44, 48
ET704
ET705
CONTINUED
ACTIVE
OR
INACTIVE
If the brake lights are working:
check the continuity and the absence of interference resistance on the following
connection:
– connection code 5A between components 160 and 120, 645, 119.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the wiring, otherwise replace it.
If the brake lights are not operational, check:
– the condition and fitting of the brake switch,
– the condition and conformity of the brake light fuse,
– the conformity of the values in the following table:
disconnect the switch and carry out the following checks:
for MEGANE II and SCENIC II with ESP
Continuity between
connectionsInsulation between
connections
Switch engaged
(Brake pedal released)5A and BPT 65G and SP17
Switch released
(Brake pedal depressed)65G and SP17 5A and BPT
For MEGANE II and SCENIC II without ESP
Continuity between
connectionsInsulation between
connections
Switch engaged
(Brake pedal released)5A and BPT 65G and SP17
Switch released
(Brake pedal depressed)65G and SP17 5A and BPT
Replace the switch if the values obtained are not correct.