2011 RENAULT SCENIC air conditioning

13B-152
MR-372-J84-13B050$585.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET088
REQUEST TO START COMPRESSOR
STATUS DEFINITION"ACTIVE": This status indicates that the compressor activation request is active.
"INACTIVE": This status indicates that the compressor activation request is not active.
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
>80 °C
ACTIVE
Status ET088 becomes ACTIVE if there has been a request for air conditioning (press
on AC or AUTO button, with maximum cold request) and status ET004 is YES.
The selection is made on the air conditioning control panel, the request for air
conditioning is transmitted to the UCH which in turn transmits the request to the
injection computer which either authorises or does not authorise compressor activation.
If the injection computer authorises compressor switch-on, the injection computer
sends the compressor switch-on request to the UPC and status ET088 becomes
""ACTIVE" (Climate control).
If the vehicle is equipped with manual air conditioning, the air conditioning request is
transmitted from the air conditioning control panel to the UCH which then accepts or
does not accept the air conditioning compressor coming on depending on the operating
status of the passenger compartment fan. When the request has been accepted, the
request to switch on the compressor is transmitted to the injection computer which
either authorises or does not authorise the compressor to start.
If the injection computer authorises compressor switch-on, it sends the request for
compressor switch-on to the UPC and status ET088 becomes "ACTIVE".
If there has been no compressor switch-on request and status ET088 remains
"ACTIVE", see62A, Air conditioning.
Note: Compressor operation is only authorised when the engine is running.
Compressor activation is commanded by the UPC.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
SID301_V44_ET088/SID304_V45_ET088/SID301_V48_ET088/SID304_V49_ET088/SID304_V4D_ET088/SID301_V4C_ET088

13B-153
MR-372-J84-13B050$585.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET088
CONTINUED
INACTIVE
Status ET088 is "INACTIVE" when no air conditioning request has been made. When
compressor switch-on has not been authorised (ET004 "AC authorised" is "NO") or
when the driver switches the heating and air conditioning system off.
If there is a compressor switch-on request and status ET088 remains "INACTIVE",
see62A, Air conditioning.
Note: Compressor operation is only authorised when the engine is running.
Compressor activation is commanded by the UPC.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-171
MR-372-J84-13B050$624.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET648
FAN UNIT
STATUS DEFINITIONINACTIVE: This status indicates that the cooling fan assembly is INACTIVE.
LOW SPEED: This status indicates that the cooling fan assembly is at LOW SPEED.
HIGH SPEED: This status indicates that the cooling fan assembly is at HIGH SPEED.
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
Conformity check with the engine stopped and the ignition on, or engine running, and engine coolant
temperature > 80°C
INACTIVE
The fan assembly is inactive when the coolant temperature does not exceed 96°C.
LOW SPEEDThe injection computer requests the activation of the low speed GMV when:
– the engine coolant temperature is above 96°C,
– the injection computer has system faults that could lead to the engine
overheating,
– the air conditioning is switched on by the driver.
When the high speed fan is supplied:
–status ET022 Low speed fan request becomes activated.
The low-speed fan assembly stops when:
– the engine coolant temperature is below 94°C,
– no fault which could cause engine overheating is present in the injection
system.
– the air conditioning is not switched on by the driver.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
SID301_V44_ET648/SID304_V45_ET648/SID301_V48_ET648/SID304_V49_ET648/SID304_V4D_ET648/SID301_V4C_ET648

13B-187
MR-372-J84-13B050$663.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2DIESEL INJECTION
Fault finding – Parameter summary table13B
Tool parameter Diagnostic tool title
PR125Power absorbed by the AC* compressor Vdiag 44 and 48 only
PR128First EGR valve offset
PR129Last EGR valve offset
PR130Cruise control setpoint
PR132Air flow
PR171Air flow setpoint for EGR Vdiag 44 and 48 only
PR190Engine idle speed setpoint.
PR224Turbocharging pressure sensor voltage Vdiag 44 and 48 only
PR228Injector control capacitor voltage
PR364Cylinder no. 1 fuel flow correction
PR365Cylinder no. 4 fuel flow correction
PR381Particle filter downstream temperature
Vdiag 4D, 45 and 49 only PR382Particle filter upstream temperature
PR383Weight of soot in the particle filter
PR391Mileage since particle filter replacement
PR400New EGR valve offset
PR405Cylinder no. 2 fuel flow correction
PR406Cylinder no. 3 fuel flow correction
PR412Mileage at last successful regeneration
Vdiag 4D, 45 and 49 only PR414Particle filter diff* pressure
PR415Time since last regeneration
PR513Mileage counter for level 1 warning light
PR514Mileage counter for level 2 warning light
PR634Air flow request
PR667Turbine upstream temperature
Vdiag 4D, 45 and 49 only PR668Turbine upstream temperature sensor voltage
PR669Particle filter diff* press* sens* voltage
PR670Particle filter upstream temp* sens* voltage
PR671Particle filter downstream temp* sens* voltage
PR672Damper valve position setpoint Vdiag 44 and 48 only
*AC: air conditioning system
*diff: differential*sens: sensor
*temp: temperature*press: pressure

13B-220
MR-372-J84-13B050$741.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR125
POWER ABSORBED BY THE AIR CONDITIONING COMPRESSOR*
PARAMETER
DEFINITIONThis parameter indicates the power absorbed by the air conditioning compressor in W.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
For Kangoo II only
Conformity check with the engine stopped and the ignition on, or with the engine running without electrical
consumers, and engine coolant temperature > 80°C
PR125= 0W
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_PR125 / SID301_V48_PR125 / SID301_V4C_PR125

13B-260
MR-372-J84-13B050$819.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of commands
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
SC001
WRITE SAVED DATA
NOTESTo be able to run this command, it is essential to save the data using command SC003
Save computer data.
Writing is carried out after the computer has been reprogrammed or replaced.
Validating this command writes the data saved using command SC003 Save computer data.
The data is as follows:
– vehicle idle speed,
– programming of exhaust gas recirculation valve data,
– options available on the vehicle and managed by the computer (Example: Air conditioning),
– data specific to injection and particle filter operation.
The data configures the computer and prevents:
– engine malfunction after reprogramming or replacing the computer,
– incorrect interpretation of the information provided by the CLIP diagnostic tool.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_SC001 / SID304_V45_SC001 / SID301_V48_SC001 / SID304_V49_SC001 / SID304_V4D_SC001 / SID301_V4C_SC001

13B-261
MR-372-J84-13B050$819.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of commands
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
SC003
SAVE COMPUTER DATA
NOTESThis save is carried out before computer reprogramming or replacement.
On the CLIP tool, select the SC003 Save computer data.
If the following message appears:
"a saved file exists, do you want to overwrite this data?":
(this file corresponds to the last save made on the CLIP diagnostic tool)
select "YES".
Confirming this command saves the following vehicle-specific data:
– the egr valve data programming;
– options available on the vehicle and managed by the computer (e.g. air conditioning);
– data specific to injection and particle filter operation.
This information will be saved in the CLIP diagnostic tool.
When saving is finished, run command SC001 Write saved data in order to configure the new computer after
programming or reprogramming.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_SC003 / SID304_V45_SC003 / SID301_V48_SC003 / SID304_V49_SC003 / SID304_V4D_SC003 / SID301_V4C_SC003

13B-278
MR-372-J84-13B050$897.mif
V17
DIESEL INJECTION
Fault finding – Fault Finding Chart
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
ALP 6 Engine idle speed too low or unstable
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Check the presence and conformity of the fuel by running Test 13 Diesel fuel conformity check.
Check the injection computer: that the connections and wiring are in good condition, that earths and feeds are
present.
If the wiring is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check the air inlet circuit (refer to the interpretation of fault DF301 Air inlet circuit).
Check that the damper valve operates correctly (refer to the interpretation of fault DF641 Damper valve circuit).
Check the air flowmeter (refer to the interpretation of faults DF039 Inlet air temperature sensor circuit, DF129
Air flow requested and DF056 Air flow sensor circuit).
Check the air conditioning pressure sensor (refer to the interpretation of fault DF049 Refrigerant sensor circuit).
If the wiring is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If fault DF308 Particle filter clogged is present, replace the particle filter.
Run command RZ030 Particle filter adaptives after replacing the particle filter.
Check the low pressure fuel supply system by performing test 1 Low pressure supply check and test 2
Internal fuel transfer pump (ITP) check.
Check the high pressure fuel supply system by performing test 3 High pressure fuel pressure solenoid valve
check, test 4 High pressure pump (HPP) and fuel flow solenoid valve check and test 5 Rail high pressure
regulation circuit check.
Check the injectors by performing test 6 Major injector leak/injectors open and test 7 Incorrect injection
amount.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
SID301_V44_ALP6 / SID304_V45_ALP6 / SID301_V48_ALP6 / SID304_V49_ALP6 / SID304_V4D_ALP6 / SID301_V4C_ALP6