2011 RENAULT SCENIC check engine

13B-170
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$104.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
* diff: differential
DF312
PRESENT
OR
STOREDSPEED REQUEST
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after the engine is started or following a road test.
Special notes:
If the fault is present:
– the special regenerate particle filter warning light is lit or a warning message is
displayed on the instrument panel.
– The vehicle needs to be driven specially to activate particle filter regeneration during
driving.
Priorities when dealing with a number of faults:
Firstly, deal with the following faults:
– DF308 Particle filter clogged if it is present or stored.
– DF311 Failed regenerations limit exceeded if it is present.
– DF315 Particle filter diff* pressure sensor if it is present or stored.
The fault appears after:
– 7 failed regeneration attempts when driving and the weight of soot in the particle filter is greater than
21 g.
– the weight of soot in the particle filter is greater than 58 g.
PART A:
The flow chart on the following page can be used to analyse the driving profile and causes of the activation of this
fault.
EDC16C36_V48_DF312/EDC16C36_V58_DF312EDC16 C36
Program No.: 91
Vdiag No.: 48, 58

13B-172
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$104.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF312
CONTINUED 2
Is there at least one?
Within ET706 to ET715 Stored engine status No. 1 to No. 10:
Read the values of the statuses relating to the mileage of the last failures
These are the engine statuses at the last failures
Is the engine status value for one of the last
failures equal to STOPPED?Contact the
Techline.
Read PR383 "Weight of soot in particle filter" in the current context, and in
the context of fault DF312 appearing (the weight of soot when DF312
appeared).
Current value of PR383 > soot weight at the
time of DF312 + 5g?
A
YES
NO
NO
YES
PART
B
NOYESPART
C
EDC16 C36
Program No.: 91
Vdiag No.: 48, 58

13B-173
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$104.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF312
CONTINUED 3
PART B
1. No particle filter regeneration.
2. Write on the repair order the parameter and status relating to the last failure:
Mileage of last DF312
Mileage of last failures
Engine statuses of last failures
E.g.: PR787 = 2794 miles (4657 km); PR801 = 2760 miles (4600 km); engine status = STOPPED
3. Interpretation of the values written on the repair order by the service advisor for the customer:
Before the last time the Particle Filter message or warning light illuminated (appeared at the Mileage of the
last DF312), the customer had not adhered to the driving recommendations: the failure that occurred at the
Mileage of the last failure is due to the engine being switched off.
4. Explain to the customer the procedure to turn off the warning light, making use of the parameters noted in the
repair order: see PA R T D.
PART C
Check that there are no leaks or blockages in the exhaust pipe,
Repair if necessary
Carry out an After-Sales regeneration with the consent of the Techline.
Follow the procedure for command SC017 Particle filter regeneration (see Interpretation of commands).
Explain to the customer the procedure for regeneration when driving to avoid unnecessary repairs: see PART D.
EDC16 C36
Program No.: 91
Vdiag No.: 48, 58

13B-174
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$104.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF312
CONTINUED 4
PART D
Procedure to switch off the Particle filter message or warning light on the instrument panel
The customer must carry out a specific driving operation (cf. vehicle user manual) that consists of:
1. When the engine is warm, drive at a speed greater than 36 mph (60 km/h) for 1 minute to trigger the
regeneration procedure.
2. Keep driving at an average speed of 36 mph (60 Km/h), until the particle filter message or warning light on
the instrument panel goes out. In order for the procedure to succeed, it is necessary to drive without stopping
the engine or leaving the engine running at idle speed for an extended period of time. The regeneration time
depends on the vehicle and driving conditions but should last for 20 minutes maximum.
3. If regeneration when driving fails (the warning light has not switched off or the service warning light has come
on), carry out a particle filter regeneration in the Renault dealership. Run command SC017 Particle filter
regeneration (see interpretation of commands).
Check that there are no leaks or blockages in the exhaust pipe.
Repair if necessary
If the fault is still present, contact the Techline.
EDC16 C36
Program No.: 91
Vdiag No.: 48, 58

13B-175
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$104.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
* diff: differential
DF315
PRESENT
OR
STOREDPARTICLE FILTER DIFF* PRESSURE SENSOR
CO: Open circuit
CC.1: Open circuit or short-circuit on + 12 volts
C0.0: Open circuit or short circuit to earth
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after the engine is started or following a road test.
Special notes:
If the fault is present:
–the level 1 warning light is lit,
–the OBD warning light will come on after three consecutive driving cycles (start
+ 5 seconds + switch off the ignition switched and wait 1 minute),
– the particle filter fault finding procedure is inhibited,
– particle filter regeneration is inhibited.
Priorities when dealing with a number of faults:
– DF315 if it is present.
– DF308 "Particle filter clogged" if DF315 is stored and DF308 is present.
– DF011 Sensor supply voltage no. 1 if it is present or stored.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
EDC16C36_V48_DF315/EDC16C36_V50_DF315/EDC16C36_V58_DF315EDC16 C36
Program No.: 91
Vdiag No.: 48, 50, 58

13B-176
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$104.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF315
CONTINUED 1
CC.1NOTESNone.
Check the condition of the connector of the differential pressure sensor.
Check the condition of the connector of the engine management computer.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation in relation to + 12 V on the following connections:
– connection code3TL,
– connection code3TM,
between components 120 and 1290.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the differential pressure sensor.
EDC16 C36
Program No.: 91
Vdiag No.: 48, 50, 58

13B-177
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$104.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF315
CONTINUED 2
CO.0
CONOTESNone.
Check the condition of the connector of the differential pressure sensor (see Wiring Diagram Technical Note,
Mégane II ph2, Scénic II ph2, Component code 1290).
Check the condition of the connector of the engine management computer (see Wiring Diagram Technical Note,
Mégane II ph2, Scénic II ph2, Component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity and insulation to earth of the following connections:
– connection code3TL,
– connection code3TM,
between components 120 and 1290.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the wiring of the particle filter downstream temperature sensor, component code 1288, is present (with or without
the sensor being present), check the electrical insulation in relation to + 12 V between the following connections:
• 3XU between components 120 and 1288,
• 3TG between components 120 and 1288.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the differential pressure sensor.
EDC16 C36
Program No.: 91
Vdiag No.: 48, 50, 58

13B-178
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$104.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
* diff: differential
DF316
PRESENT
OR
STOREDPARTICLE FILTER DIFF* PRESSURE
1.DEF: Signal incoherent
2.DEF: Below minimum threshold
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
– the ignition is switched on.
– the engine is started.
Special notes:
If the fault is present:
– the particle filter fault finding procedure is inhibited,
–the Level 1 and OBD warning lights are lit.
Use bornier Ele. 1681 for all operations on the engine management computer
connector.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
Check the condition of the pressure pipes on the differential pressure sensor.
Check that they are sealed and in the correct position.
Replace if necessary.
Check the condition of the connectors on the differential pressure sensor and the injection computer.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
Check the continuity, insulation and the absence of interference resistance on the following connections:
– Connection code3AAQ,
– Connection code3TM,
– Connection code 3TL,
between components 1290 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
EDC16C36_V48_DF316/EDC16C36_V50_DF316/EDC16C36_V58_DF316EDC16 C36
Program No.: 91
Vdiag No.: 48, 50, 58