2011 RENAULT SCENIC ignition

13B-158
MR-372-J84-13B200$360.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of faults
EDC16
Program No.: C1
Vdiag no.: 18, 1C, 20,
50, 58, 5C
13B
*diff: differentialDF953
PRESENT
OR
STORED
PARTICLE FILTER ABSENT
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after the engine is started or following a road test.
Special notes:
If the fault is present:
– particle filter regeneration is inhibited,
– blue/white smoke and black particles coming from the exhaust,
– the OBD warning light illuminates after three consecutive driving cycles (starting
+ 5 seconds + switch off the ignition and wait 1 minute).
Priorities when dealing with a number of faults:
Firstly, deal with the following faults:
–DF315 Particle filter diff* pressure sensor if it is present or stored.
–DF717 Particle filter upstream pressure if it is present or stored.
Use bornier Elé.1681 for all operations on the engine management computer
connector.
IMPORTANT
In the long term, this fault may lead to premature wear and a greater risk of
turbocharger failure.
Check the condition of the differential pressure sensor connector (see Wiring Diagram Technical Note,
Mégane II, Scénic II or Laguna II, component code 1290).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Mégane II, Scénic II or Laguna II, component code 120).
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, wiring: Precautions for repair), repair the connector(s); otherwise, replace the wiring.
Check the particle filter is present.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16_V50_DF953/EDC16_V58_DF953/EDC16_V5C_DF953/EDC16_V18_DF953/EDC16_V1C_DF953/EDC16_V20_DF953

13B-162
MR-372-J84-13B200$468.mif
V13
13B
DIESEL INJECTION
Fault finding – Status summary table
Tool status Diagnostic tool title
ET001+ After ignition computer feed
ET003Engine immobiliser
ET004Air conditioning authorisation
ET007Pre-postheating unit control
ET014Monitor cooling fan 1
ET015Monitor cooling fan 2
ET021High speed fan assembly request
ET022Low speed fan assembly request
ET038Engine
ET042Cruise control/speed limiter
ET076Starting
ET077Impact detected
ET079Air conditioning present
ET088Compressor actuation request
ET104Injector code use
ET111Number of passenger compartment heating resistors fixed (Vdiag 50 only)
ET112Passenger compartment heating resistors cut out (Vdiag 50 only)
ET143Low-speed fan assembly relay control (Vdiag 18, 1C, 20 only)
ET144High-speed fan assembly relay control (Vdiag 18, 1C, 20 only)
ET205Heating element no. 1 relay control (Vdiag 58 only)
ET206Heating element no. 2 relay control (Vdiag 58 only)
ET207Heating element no. 3 relay control (Vdiag 58 only)
ET238Synchronisation
ET341Immobiliser code programmed
ET405Clutch pedal switch
ET415Cruise control/speed limiter deactivation
ET651EGR programming cut-off
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
MR-372-J84-13B200$468.mif

13B-164
MR-372-J84-13B200$504.mif
V13
13B
DIESEL INJECTION
Fault finding – Interpretation of statuses
ET001
COMPUTER + AFTER IGNITION FEED
STATUS DEFINITIONPRESENT, this status indicates that the + after ignition feed is active.
ABSENT, this status indicates that the + after ignition feed is inactive.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Conformity check with the engine stopped and the ignition on, or engine running, and engine coolant
temperature > 80°C
PRESENT
With the ignition on and engine running warm at idle speed, + after ignition feed is
activated.
In the event of a fault, apply the interpretation of DF046 Battery voltage or DF151 Main
relay circuit.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
EDC16_V18_ET001/EDC16_V1C_ET001/EDC16-V20_ET001/EDC16_V50_ET001/EDC16_V58_ET001/EDC16-V5C_ET001 EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
MR-372-J84-13B200$504.mif

13B-165
MR-372-J84-13B200$504.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of statuses
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
ET001
CONTINUED
Sensor electrical conformity
"ABSENT"
NOTESIgnition on
Check the condition and the conformity of the supply fuse F5D (5A) of the Protection and Switching Unit
(Vdiag 18, 1C, 20 only).
Repair if necessary
Check for an earth on connection NT (Laguna II) or N (Mégane II and Scénic II) of component 120.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for a + 12 V feed on connection AP29 (Laguna II) or AP15 (Mégane II and Scénic II) of the injection
computer.
If there is no voltage, check the continuity and insulation from earth of connection AP29 (Laguna II) or AP15
(Mégane II and Scénic II) between components 120 and 1337 (Vdiag 18, 1C, 20 only) or 597 (Vdiag 50, 58, 5C
only).
If the connection or connections are faulty and there is a repair method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
PRESENT
NOTESIgnition on
Check that there is no + 12 V feed with the ignition off on connection AP29 (Laguna II) or AP15 (Mégane II and
Scénic II) of component 120.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-166
MR-372-J84-13B200$504.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET003
ENGINE IMMOBILISER
STATUS DEFINITIONACTIVE, this status indicates that the immobiliser is active.
INACTIVE, this status indicates that the immobiliser is inactive.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
> 80°C
ACTIVE
Refer to the fault finding note for the UCH (see 87B, Passenger compartment
connection unit).
INACTIVERefer to the fault finding note for the UCH (see 87B, Passenger compartment
connection unit).
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_ET003/EDC16_V58_ET003/EDC16-V5C_ET003/EDC16_V18_ET003/EDC16_V1C_ET003/EDC16-V20_ET003

13B-167
MR-372-J84-13B200$504.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET004
AC AUTHORISED
STATUS DEFINITIONYES, this status indicates that the air conditioning is active.
NO, this status indicates that the air conditioning is inactive.
NOTESSpecial notes
Only perform these tests if the statuses do not correspond with the system
programming functions.
Engine running, engine coolant temperature > 80 °C
YES
The air conditioning authorisation only changes to YES if:
– the air conditioning request has been made by the driver (air conditioning switch in
AC or AUTO position with minimum ventilation),
– the engine is not under full load,
– the air conditioning system is not faulty.
Conformity check with engine stopped and ignition on
NOStatus ET004 remains NO under the following conditions:
– Vehicle stopped with the ignition on,
– faults present in the air conditioning circuit,
– no air conditioning request made by the driver,
– engine under full load.
If status ET004 remains NO then the air conditioning should be authorised, check:
– that the air conditioning compressor is activated correctly,
– the air conditioning system feed fuses,
– the presence of refrigerant in the air conditioning circuit,
– that the refrigerant fluid pressure value is consistent at idle speed.
If the fault is still present, check the air conditioning computer faults (see62C, Air
conditioning).
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_ET004/EDC16_V58_ET004/EDC16-V5C_ET004/EDC16_V18_ET004/EDC16_V1C_ET004/EDC16-V20_ET004

13B-168
MR-372-J84-13B200$504.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET007
PRE-POSTHEATING UNIT CONTROL
STATUS DEFINITIONACTIVE, when the heater plugs are activated according to the engine coolant
temperature.
INACTIVE, after the engine has been running for a certain period.
In the event of a fault, consult the interpretation of fault DF017 Preheating unit
control circuit.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Conformity check with engine running, engine coolant temperature > 80 °C
"ACTIVE"
Then
"INACTIVE"
After the engine has been running for a certain period, the status changes from ACTIVE
to INACTIVE.
In the event of a fault, consult the interpretation of fault DF017 Preheating unit control
circuit.
Sensor conformity check
ACTIVEWhen the vehicle is started from cold, the injection computer controls the pre-
postheating unit so that the vehicle can be started.
Status ET007 becomes YES a few seconds after the ignition is switched on and during
pre/postheating.
If the vehicle does not start and status ET007 becomes YES, check:
– supply fuse F2 (Scénic II and Mégane II) or FM12 (Laguna II) (70A) for the
preheating unit, located on the power supply fuse board in the engine compartment
connection unit, below the Protection and Switching Unit,
– the resistance of the heater plugs.
Replace any plug with a resistance greater than 2Ω.
If the vehicle starts and status ET007 remains YES during the engine operating phase,
refer to the interpretation of faults:
– DF017 Preheating relay control circuit.
– DF025 Pre-postheating unit diagnostic connection.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_ET007/EDC16_V58_ET007/EDC16_V5C_ET007/EDC16_V18_ET007/EDC16_V1C_ET007/EDC16-V20_ET007

13B-170
MR-372-J84-13B200$504.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET014
CHECK COOLING FAN 1
STATUS DEFINITIONRUNNING, this status indicates that the fan assembly is engaged.
STOPPED, this status indicates that the fan assembly is not engaged.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
NOTE:
Statuses ET014 and ET022 Low-speed fan assembly request change status simultaneously.
Conformity check with the engine stopped and the ignition on, or engine running, and engine coolant
temperature > 80°C
RUNNING
The low-speed engine fan is supplied in three scenarios:
– the engine coolant temperature is greater than 89°C,
– the air conditioning is operating,
– the injection computer has system faults that could lead to the engine overheating.
When the low-speed fan assembly is supplied:
–status ET014 becomes RUNNING and status ET022 Low-speed fan assembly
request becomes ACTIVE.
If the low-speed fan assembly does not work, refer to the fault finding note for the
Protection and Switching Unit (Vdiag 18, 1C, 20 only).
Conformity check with engine stopped and ignition on.
STOPPEDThe low-speed fan assembly stops when:
– the engine coolant temperature is less than 89°C
– the air conditioning is not switched on by the driver.
IMPORTANT!WARNING
If the Protection and Switching Unit (Vdiag 18, 1C, 20 only) no longer detects the injection
computer signals, the low-speed fan assembly is supplied until the battery is completely
discharged.
If the low-speed fan assembly is defective, the high-speed fan assembly will be activated.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
EDC16_V50_ET014/EDC16_V58_ET014/EDC16_V5C_ET014/EDC16_V18_ET014/EDC16_V1C_ET014/EDC16_V20_ET014