13B-65
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$329.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF051
PRESENT
OR
STOREDCRUISE CONTROL/SPEED LIMITER FUNCTION
1.DEF : signal incoherence
2.DEF : inconsistent vehicle speed
3.DEF : controls at the steering wheel
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after the engine is started or following a road test.
Special notes:
The cruise control/speed limiter function is inhibited.
Use bornier Elé. 1681 for all operations on the injection computer connectors.
WARNING
This fault may appear if the wiring harness has been damaged.
Follow the procedure described in the Wiring Check in the Introduction.
This check enables the condition and the conformity of the engine wiring harness to be checked.
If fault DF051 is present, refer to the Cruise control/Speed limiter section of the conformity check and refer to
interpretation of statuses ET042 Cruise control/Speed limiter, ET415 Cruise control/Speed limiter
deactivation and ET703 Cruise control/Speed limiter buttons.
Check that by pressing the buttons the statuses change and that, with the ignition switched on, all the values
are correct.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF051/EDC16_V48_DF051/EDC16_V4C_DF051
13B-172
DIESEL INJECTION
Fault finding - Interpretation of statuses13B
V10 MR-372-J84-13B150$564.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
ET415
(CONTINUED 2)
STATUS 4Cancel button pressed
The cruise control/speed limiter function is deactivated whenever the suspend button is
pressed.
Status ET415 becomes STATUS 4, when driving when:
- Either the cruise control is active.
- The speed limiter is active,
- and the driver presses the 0 button.
This action deactivates the Cruise control/Speed limiter.
Reinitialise status ET415 on the injection computer by running command RZ001
Fault memory.
If status ET415 becomes STATUS 4 without pressing the 0 button, consult the
interpretation of status ET703 Cruise control/speed limiter buttons and run fault
finding on the R/0 control button located on the right-hand side of the steering wheel.
STATUS 5Cruise control or speed limiter monitoring
This status appears when the vehicle brakes or decelerates sharply without the injection
computer receiving a signal that the brake pedal switch has been pressed.
If status ET415 is STATUS 5, refer to the interpretation:
- of status ET042 Cruise control / speed limiter,
- of status ET703 Cruise control / speed limiter buttons,
- of status ET704 Brake switch no. 1,
- of status ET705 Brake switch no. 2,
to test the cruise control/speed limiter system components and find the defective
component.
Also check the operation of the accelerator pedal, and check with the diagnostic tool for
a fault connected with this component. Deal with them if necessary.
Reinitialise status ET415 on the injection computer by running command RZ001
Fault memory.
If status ET415 changes to STATUS 5, deal with present faults or those stored in the
injection computer.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
13B-177
DIESEL INJECTION
Fault finding - Interpretation of statuses13B
V10 MR-372-J84-13B150$564.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
ET703
(CONTINUED 1)
DECREASEStatus ET703 becomes DECREASE when the cruise control/speed limiter "-" button is
pressed. This button is on the steering wheel, on the left-hand side.
If status ET703 does not display DECREASE, check the condition of the cruise control/
speed limiter +/- button, and the condition of its connector. Repair if necessary.
To carry out these checks and measurements in complete safety, observe the
recommendations for removing the driver's front airbag (see MR 364 (Mégane II) or 370
(Scénic II), Mechanical, 88C, Airbag and pretensioners, Driver's front airbag,
Removal - Refitting).
Measure the resistance of the following connection whilst pressing the "-" button
(on the button tracks):
– Connection code86G of component 331.
– Connection code 86M of component 331.
If the resistance is not approximately 100 Ω, check the continuity of the button in rest
position.
If there is continuity, replace the +/- control button.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
SUSPENDStatus ET703 becomes SUSPEND when the cruise control/speed limiter 0 button is
pressed. This button is located on the steering wheel, to the right.
If status ET703 does not change to SUSPEND, check the condition of the cruise control/
speed limiter R/0 button, and the condition of its connector.
To carry out these checks and measurements in complete safety, observe the
recommendations for removing the driver's front airbag (see MR 364 (Mégane II) or 370
(Scénic II), Mechanical, 88C, Airbag and pretensioners, Driver's front airbag,
Removal - Refitting).
Measure the resistance of the following connection whilst pressing the 0 button
(on the button tracks):
– Connection code86G of component 331.
– Connection code 86M of component 331.
If the resistance is not approximately 0 Ω, replace the R/0 control button.
If there is continuity, replace the R/0
control button.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
