2011 RENAULT SCENIC engine coolant

13B-26
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4CDIESEL INJECTION
Fault finding - Interpretation of faults
DF001
PRESENT
OR
STOREDCOOLANT TEMPERATURE SENSOR CIRCUIT
CC.0 : short circuit to earth
CO.1 : open circuit or short circuit to + 12 V
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present with the engine running or following a road test.
Special notes:
If the fault is present:
– the coolant temperature: PR064: Coolant temperature is fixed at 119°C,
– the preheating phase is greater than 10 seconds,
– the fan assembly is permanently supplied,
The level 1 warning light comes on.
Use bornier Elé. 1681 for any work on the computer connectors.
CC.0
NOTESNone.
Check the coolant temperature sensor connections.
Repair if necessary.
Measure the resistance of the coolant temperature sensor between terminals 2 and 3 of its black connector.
Replace the sensor if its resistance is not approximately: 12460±112Ω at -10°C
2252±112Ω at 25°C
811.4±39Ω at 50°C
283±8Ω at 80°C
115±3Ω at 110°C
Check the injection computer connections.
Check for continuity and the absence of interference resistance of the following connections:
Injection computer brown 48-track connector B, track F2 Track 3 coolant temperature sensor
Injection computer brown 48-track connector B, track H1 Track 2 coolant temperature sensor
Repair if necessary.
If the fault is still present, replace the coolant temperature sensor.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF001/EDC16_V48_DF001/EDC16_V4C_DF001
MR-372-J84-13B150$282.mif

13B-110
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$423.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C
MAIN COMPUTER STATUSES AND PARAMETERS (continued)
NOTESOnly carry out this conformity check after carrying out a complete check using the
diagnostic tool. The values shown in this conformity check are given as examples.
Test conditions: engine stopped, ignition on.
Order FunctionParameter or Status
Check or ActionDisplay and Notes Fault finding
5 PressurePR035:Atmospheric
pressureIndicates the
atmospheric pressure
in mbar.
The sensor is built into
the computer.
Default value:
750 mbarIn the event of a fault,
consult the interpretation
of fault DF003 Atmospheric
pressure sensor circuit.
PR038:Rail pressure0 consult the interpretation
of fault DF007 Rail pressure
sensor circuit.
6 TemperaturePR059: Inlet air
temperatureIndicates the inlet air
temperature
Ignition on
PR061 = PR059
Default value: 20°C In the event of a fault, refer
to the interpretation
of parameter PR059.
PR064: Coolant
temperatureShows the engine
coolant temperature
in °C
Default value: 119°C.In the event of a fault,
refer to the interpretation
ofDF001 Coolant
temperature sensor
circuit.
7 Preheating ET007: Pre-postheating
controlINACTIVE
or
ACTIVEIn the event of a fault,
refer to the interpretation
of statusET007.
8 Torque PR015: Engine torqueX = 0 NmNone.
9Charging
circuit PR016:Alternator flow X = 0 mAIn the event of a fault,
check the charge circuit.

13B-118
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$423.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C
COLD LOOP (continued)
NOTESOnly carry out this conformity check after carrying out a complete check using the
diagnostic tool. The values shown in this conformity check are given as examples.
Test conditions: engine stopped, ignition on.
Order FunctionParameter or Status
Check or ActionDisplay and Notes Fault finding
7 Engine coolingET022: Low speed fan
assembly
requestWith the ignition
switched on < 80°
INACTIVEIf the fan assemblies are
supplied with the ignition
on, the injection system may
be in defect mode.
Carry out a system fault test
and refer to the
interpretation of any faults. ET021: High speed fan
assembly
request
ET014: Fan assembly 1
checkWith the ignition
switched on < 80°
STOPPED
ET015: Fan assembly 2
check
8Coolant
temperaturePR064: Coolant
temperatureShows the engine
coolant temperature
in °C
Default value:
119°CIn the event of a fault,
refer to the interpretation
ofDF001 Coolant
temperature sensor
circuit.
9 Vehicle speed PR089: Vehicle speedGives the vehicle
speed in mph.
This parameter is
transmitted by the
ABS computer. This
signal is transmitted
to the injection
system on the
multiplex network.
Ignition on
PR089 = 0 mph
(0 km/h).In the event of a fault, test
the multiplex network. Refer
to the ABS fault finding note
for the interpretation
of possible faults (see 38C,
ABS).

13B-120
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$423.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C
HEATING
NOTESOnly carry out this conformity check after carrying out a complete check using the
diagnostic tool. The values shown in this conformity check are given as examples.
Test conditions: engine stopped, ignition on.
Order FunctionParameter or Status
Check or ActionDisplay and Notes Fault finding
1Coolant
temperaturePR064: Coolant
temperatureShows the engine
coolant temperature
in °C
Default value: 119°C.In the event of a fault,
refer to the interpretation
ofDF001 Coolant
temperature sensor
circuit.
2Resistance
Heating
Passenger
compartmentET111: Set number
of RCHIndicates the number
of passenger
compartment resistors
supplied.
The passenger
compartment resistor
function programming
is performed through
the UCH.
Certain operating
parameters determine
the operation of one
or more passenger
compartment resistors.
The injection computer
only receives a signal
relating to the number
of passenger
compartment resistors
to control.
Ignition on
ET111 = NOIn the event of a fault,
(see 87B, UCH).
ET112: RCH cut-offStatus ET112 is
indicated if the
passenger
compartment resistors
are being controlled.
The computer receives
the signal to cut-off
the resistors through
the UCH.
Ignition on
ET112 = YES

13B-124
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$423.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C
ENGINE COOLING
NOTESOnly carry out this conformity check after carrying out a complete check using the
diagnostic tool. The values shown in this conformity check are given as examples.
Test conditions: engine stopped, ignition on.
Order FunctionParameter or Status
Check or ActionDisplay and Notes Fault finding
1Coolant
temperaturePR064: Coolant
temperatureShows the engine
coolant temperature
in °C
Default value: 119°C.In the event of a fault,
refer to the interpretation
of DF001 Coolant
temperature sensor
circuit.
2 Fan assembliesET022: Low speed fan
assembly
requestWith the ignition
switched on,
engine < 80°
INACTIVEIf the fan assemblies are
supplied with the
ignition on, the injection
may be in defect mode.
Carry out a system fault
test and consult
the interpretation of faults. ET021: High speed fan
assembly
request
ET014: Fan assembly 1
checkWith the ignition
switched on,
engine < 80°
STOPPED ET015: Fan assembly 2
check
3 Sensor feed PR084:Coolant
temperature
sensor voltageX = 3 V ± 0.5
Default value: 5 VIn the event of a fault,
refer to the interpretation
of DF001 Coolant
temperature sensor
circuit.

13B-125
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$423.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C
IGNITION/PREHEATING
NOTESOnly carry out this conformity check after carrying out a complete check using the
diagnostic tool. The values shown in this conformity check are given as examples.
Test conditions: engine stopped, ignition on.
Order FunctionParameter or Status
Check or ActionDisplay and Notes Fault finding
1 Power supply ET001: + After ignition
computer feedIgnition on PRESENTIf the event of a fault, carry
out fault finding on
thecharge circuit.
2 Engine speed PR055: Engine speed Indicates the engine's
rotation speed in rpm.In the event of a fault,
consult the interpretation
of fault DF005 Engine
speed sensor circuit.
3 TemperaturePR064: Coolant
temperatureShows the engine
coolant temperature in
°C
Default value: 119°C.In the event of a fault,
refer to the interpretation
ofDF001 Coolant
temperature sensor
circuit.
PR059:Inlet air
temperatureIndicates the inlet air
temperature
Default value: 20°C.In the event of a fault,
refer to the interpretation
of fault DF039 Inlet air
temperature sensor
circuit.
4 Preheating ET007: Preheating unit
controlStatus ET007 is
ACTIVE a few seconds
after the ignition is
switched on, and for
postheatingIn the event of a fault,
(ET007 locked in ACTIVE
status), consult
the interpretation of fault
DF017 Preheating unit
control circuit.

13B-128
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$423.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C
MAIN COMPUTER STATUSES AND PARAMETERS
NOTESOnly carry out this conformity check after carrying out a complete check using the
diagnostic tool. The values shown in this conformity check are given as examples.
Test conditions: engine at idle speed, coolant temperature at > 80°.
Order FunctionParameter or Status
Check or ActionDisplay and Notes Fault finding
1 Vehicle impact ET077: Impact detectedYES or NOIn the event of a fault,
refer to the interpretation
of fault DF069 Impact
detected signal.
2 Power supplyET001:+ After ignition
computer feedPRESENT, ignition on
If there is a fault carry out
a fault finding test on
thecharge circuit.
PR071: Computer feed
voltage9V PR368: Sensor
reference
voltage3.47 V < X < 3.75 V
(Average of the three
sensor feed voltages)In the event of a fault,
consult the interpretation
of faults DF011 Sensor
feed voltage no. 1,
DF012 Sensor feed
voltage no. 2 and DF013
Sensor feed voltage no. 3.
PR076: Refrigerant
sensor voltage0V consult the interpretation
of fault DF049 Refrigerant
sensor circuit.
3 Engine running PR055: Engine speedIndicates the engine's
rotation speed in rpm.
PR055 = 800 rpmIn the event of a fault,
consult the interpretation
of fault DF005 Engine
speed sensor circuit.
4Injection
configurationET104: Injector code
useYES or NO
or
DEFECTIVEThis status indicates that the
IMA function is activated.
In the event of a fault,
consult the interpretation
of DF276 Injector code
programming.

13B-129
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$423.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C
MAIN COMPUTER STATUSES AND PARAMETERS (continued)
NOTESOnly carry out this conformity check after carrying out a complete check using the
diagnostic tool. The values shown in this conformity check are given as examples.
Test conditions: engine at idle speed, coolant temperature at > 80°.
Order FunctionParameter or Status
Check or ActionDisplay and Notes Fault finding
5PressurePR035: Atmospheric
pressureIndicates the
atmospheric pressure
in mbar. The sensor is
built into the computer.
Default value:
750 mbar.In the event of a fault,
consult the interpretation
of fault DF003
Atmospheric pressure
sensor circuit.
PR038: Rail pressure250< P< 300bar
Pmax = 1350 barIn the event of a fault,
consult the interpretation
of fault DF007 Rail
pressure sensor circuit.
6 TemperaturePR059: Inlet air
temperatureIndicates the inlet air
temperature
Default value: 20°CIn the event of a fault, refer
to the interpretation
of parameter PR059.
PR064: Coolant
temperatureShows the engine
coolant temperature in
°C
Default value: 119°C.In the event of a fault, refer
to the interpretation
ofDF001 Coolant
temperature sensor
circuit.
7 Preheating ET007: Pre-postheating
controlINACTIVE
warm engineIn the event of a fault, refer
to the interpretation of status
ET007.
8 Torque PR015: Engine torqueWhen starting:
25 < X < 40 N.m
At idle speed:
2 9Charging
circuitPR016: Alternator flowWarm engine
10 < X < 20 mA
With consumers:
25 check the charge circuit.