2011 Peugeot RCZ lock
[x] Cancel search: lockPage 54 of 276
52
Folding the key
)
First press this button to fold the key.
LOCATING YOUR VEHICLE
REMOTE CONTROL PROBLEM
Following disconnection of the vehicle battery, replacement of the
remote control battery or in the event of a remote control malfunction,
you can no longer unlock, lock or locate your vehicle.
)
First of all, use the key in the lock to unlock or lock your vehicle.
)
Then, reinitialise the remote control.
If the problem persists, contact a PEUGEOT dealer as soon as
possible.
Reinitialisation
)
Switch off the ignition.
)
Turn the key to position 2 (Ignition on)
.
)
Press the closed padlock immediately for a few seconds.
)
Switch off the ignition and remove the key from the ignition switch.
The remote control is fully operational again.
Changing the battery
Battery ref.: CR1620/3 volts.
If the battery is fl at, you are informed by illumination of this
warning lamp, accompanied by an audible signal and an alert
message in the screen.
)
Unclip the casing using a coin at the notch.
)
Slide the fl at battery out of its location.
)
Slide the new battery into its location observing the original
direction.
)
Clip the casing.
)
Reinitialise the remote control.
This function allows you to identify your vehicle from a
distance, particularly in poor light. Your vehicle must be
locked.
)
Press the closed padlock on the remote control.
This will switch on the courtesy lamps and the direction indicators will
fl ash for a few seconds.
Page 55 of 276
2/
ACCESS
LOST KEYS
Visit a PEUGEOT dealer with the vehicle's V5 registration
document and your personal identifi cation documents.
The PEUGEOT dealer will be able to retrieve the key code and
the transponder code required to order a replacement key.
LOCKING THE VEHICLE
Driving with the doors locked may make access to the passenger
compartment by the emergency services more diffi cult in an emergency.
As a safety precaution (with children on board), remove the key from the
ignition when you leave the vehicle, even for a short time.
REMOTE CONTROL
The high frequency remote control is a sensitive system; do not
operate it while it is in your pocket as there is a possibility that it
may unlock the vehicle, without you being aware of it.
Do not repeatedly press the buttons of your remote control out of
range and out of sight of your vehicle. You run the risk of stopping it
from working and the remote control would have to be reinitialised.
The remote control does not operate when the key is in the
ignition, even when the ignition is switched off, except for
reinitialisation.
ANTI-THEFT PROTECTION
Do not make any modifi cations to the electronic engine
immobiliser system; this could cause malfunctions.
Do not throw the remote control batteries away, they contain
metals which are harmful to the environment.
Take them to an approved collection point.
WHEN PURCHASING A SECOND-HAND
VEHICLE
Have the key codes memorised by a PEUGEOT dealer, to ensure
that the keys in your possession are the only ones which can start
the vehicle.
Page 56 of 276
54
ALARM *
System which protects and provides a deterrent against theft and break-
ins. It provides the following types of monitoring.
- Exterior perimeter
The system checks for opening of the vehicle.
The alarm is triggered if anyone tries to open a door, the boot, the
bonnet...
- Interior volumetric
The system checks for any variation in the volume in the passenger
compartment.
The alarm is triggered if anyone breaks a window, enters the passenger
compartment or moves inside the vehicle.
- Tilt
The system checks for any change in the attitude of the vehicle.
The alarm is triggered if the vehicle is lifted, moved or knocked.
For all work on the alarm system, contact a PEUGEOT dealer or a
qualifi ed workshop.
LOCKING THE VEHICLE WITH FULL ALARM
SYSTEM
Activation
)
Switch off the ignition and get out of the vehicle.
)
Press the locking button on the remote control.
The monitoring system is active: the indicator lamp in the button fl ashes
once per second.
After the locking button on the remote control is pressed, the exterior
perimeter monitoring is activated after a delay of 5 seconds and the
interior volumetric and anti-tilt monitoring after a delay of 45 seconds.
Deactivation
)
Press the unlocking button on the remote control.
The alarm system is deactivated: the indicator lamp in the button goes off.
Self-protection function
The system checks for the putting out of service of its
components.
The alarm is triggered if the battery, the central control or the siren
wiring are put out of service or damaged.
*
According to country. If an opening (door, boot...) is not closed fully, the vehicle is not
locked but the exterior perimeter monitoring will be activated after
a delay of 45 seconds at the same time as the interior volumetric
and anti-tilt monitoring.
Page 57 of 276
2/
ACCESS
LOCKING THE VEHICLE WITH EXTERIOR
PERIMETER MONITORING ONLY
Deactivation of the interior volumetric and anti-tilt monitoring
)
Switch off the ignition.
)
Within ten seconds, press the button until the indicator lamp is on
continuously.
)
Get out of the vehicle.
)
Press the locking button on the remote control immediately.
The exterior perimeter monitoring alone is activated: the indicator lamp
in the button fl ashes once per second.
Reactivation of the interior volumetric and anti-tilt monitoring
)
Press the unlocking button on the remote control to deactivate the
exterior perimeter monitoring.
)
Press the locking button on the remote control to activate all the
monitoring functions.
The indicator lamp in the button again fl ashes once per second.
Deactivate the interior volumetric and anti-tilt monitoring to avoid
unwanted triggering of the alarm in certain cases such as:
- leaving a pet in the vehicle,
- leaving a window partially open,
- washing your vehicle,
- changing a wheel,
- having your vehicle towed,
- transport by sea. To be effective, this deactivation must be carried out each time the
ignition is switched off.
Page 58 of 276
56
OPERATING FAULT
AUTOMATIC ACTIVATION *
LOCKING THE VEHICLE WITHOUT ACTIVATING
THE ALARM
)
Lock or deadlock the vehicle using the key in the driver's door lock.
When the ignition is switched on, fi xed illumination of the indicator lamp
in the button indicates a fault with the system.
Have it checked by a PEUGEOT dealer or a qualifi ed workshop.
2 minutes after the last door or the boot is closed, the system is
activated automatically.
)
To avoid triggering the alarm on entering the vehicle, fi rst press the
unlocking button on the remote control.
* According to country.
FAILURE OF THE REMOTE CONTROL
To deactivate the monitoring functions:
)
Unlock the vehicle using the key in the driver's door lock.
)
Open the door; the alarm is triggered.
)
Switch on the ignition; the alarm stops. The indicator lamp in the
button goes off.
TRIGGERING OF THE ALARM
The monitoring functions remain active until the alarm has been
triggered eleven times in succession.
When the vehicle is unlocked using the remote control, rapid
fl ashing of the indicator lamp in the button informs you that the
alarm was triggered during your absence. When the ignition is
switched on, this fl ashing stops immediately.
This is indicated by sounding of the siren and fl ashing of the direction
indicators for thirty seconds.
Page 59 of 276
2/
ACCESS
ELECTRIC WINDOWS
Fitted with a safety anti-pinch system.
A.
Left-hand electric window control switch.
B.
Right-hand electric window control switch.
ONE-TOUCH ELECTRIC WINDOWS
There are two options:
- manual mode
)
Press or pull the switch gently. The window stops when the
switch is released.
- automatic mode
)
Press or pull the switch fi rmly. The window opens or closes fully
when the switch is released.
)
Pressing the switch again stops the movement of the window.
The electric window switches remain operational for approximately
45 seconds after the ignition is switched off or until the vehicle is
locked after a door is opened.
If the passenger's window cannot be operated from the driver's
door control panel, carry out the operation from the control panel
of the passenger door.
After approximately ten consecutive complete opening/closing
movements of the window, a protection function is activated which
only authorises closing of the windows, so as to prevent damage
to the electric window motor.
Once the window is closed, the switches will become operational
again after approximately 40 minutes.
Safety anti-pinch
When the window rises and meets an obstacle, it stops and partially
lowers again.
If the window cannot be closed (for example, in the presence of ice),
immediately after the movement is reversed:
)
press and hold the switch until the window opens fully,
)
then pull the switch immediately and hold it until the window
closes,
)
continue to hold the switch for approximately one second after
the window has closed.
The safety anti-pinch function is not operational during these
operations.
Page 61 of 276
2/
ACCESS
DOORS
OPENING
From outside
)
After unlocking the vehicle completely using the remote control or
the key, take hold of the door handle then pull it.
The window lowers automatically by a few millimetres to permit
opening of the door.
In freezing conditions, the presence of ice may hinder the automatic
partial opening of the window; remove the ice which may have
formed along the lower seal, located at the base of the window.
When the selective unlocking is activated, the fi rst press of the
remote control unlocking button permits unlocking of the driver's
door only.
From inside
)
Pull the door control to open the door; this unlocks this vehicle
completely.
The window lowers automatically by a few millimetres to permit
opening of the door.
With the selective unlocking activated:
- the driver's door control unlocks the driver's door and the fuel
fi ller fl ap only.
- the passenger's door control unlocks the passenger's door
and the boot.
The interior door controls do not operate when the vehicle is
deadlocked. If you leave the door open for more than one minute, the window
rises again.
Pull the handle again to reactivate the system.
Page 62 of 276
60
CLOSING
The window rises automatically after a few seconds and adjusts to
provide perfect sealing when closed.
- when the engine is running
, this warning lamp comes on,
accompanied by a message in the screen for a few seconds,
CENTRAL LOCKING CONTROL
This control permits simultaneous locking or unlocking of the doors,
boot lid and fuel fi ller fl ap from inside the vehicle.
Locking
)
Press this button to lock the vehicle.
The red indicator lamp on the button comes on.
If one of the doors or the boot lid is open, the central locking from
the inside does not take place.
Unlocking
)
Press this button again to unlock the vehicle.
The red indicator lamp on the button goes off.
Locking/deadlocking from the outside
When the vehicle is locked or deadlocked from the outside, the
red indicator lamp fl ashes and the button is inactive.
)
With normal locking, pull on the interior door control lever to
unlock the vehicle.
)
With deadlocking, you have to use the remote control or the
key to unlock the vehicle.
When washing your vehicle:
- fi rst lock the vehicle using the remote control or the key,
- avoid spraying the upper part of the windows,
- keep the end of the high pressure nozzle at least 1 metre from
the windows and door seals.
When a door is not closed correctly: Be aware of the risk of pinching when the window rises
automatically on closing the door.
- when the vehicle is moving
(speed higher than 6 mph (10 km/h)),
this warning lamp comes on, accompanied by an audible signal and
a message in the screen for a few seconds.