2011 Peugeot RCZ light

FAMILIARISATION
MONITORING

The instrument panel has permanent back-
lighting for improved visibility in all situations,
both day and night.


- With the ignition on, the fuel gauge needle
should indicate the level of fuel remaining.

- With the engine running, its associated
low level warning lamp should switch off.

- With the ignition on, the oil level indicator
should display "OK" or "correct",
depending on version, for a few seconds.
If the levels are not correct, top up the levels
which are low.

INSTRUMENT PANEL
60
22

- With the ignition on, the orange and red
warning lamps come on.

- With the engine running, these warning
lamps should switch off.
If warning lamps remain on, refer to the page
concerned.

WARNING LAMPS

26 Illumination of the indicator lamp indicates the
status of the corresponding function.


A.
Emergency call in progress.


SWITCH PANEL
54 195
104
140
195

B.
Deactivating the interior volumetric and
anti-tilt sensors (alarm).

C.
Central locking.

D.
Deactivation of the ESP/ASR system.

E.
Deactivation of the front and rear parking
sensors.

F.
Access to PEUGEOT services.

20

OPTIMISE THE USE OF YOUR
GEARBOX

With a manual gearbox, move off gently,
change up without waiting and drive by
changing up quite soon. If your vehicle has
the system, the gear shift indicator invites
you to change up; it is displayed in the
instrument panel, follow its instructions.

With an automatic or electronic gearbox,
stay in Drive "D"
or Auto "A"
, according to
the type of gearbox, without pressing the
accelerator pedal heavily or suddenly.



DRIVE SMOOTHLY


Maintain a safe distance between vehicles,
use engine braking rather than the
brake pedal, and press the accelerator
progressively. These attitudes contribute
towards a reduction in fuel consumption and
CO
2 emissions and also helps reduce the
background traffi c noise.

When the traffi c is fl owing well, and if you
have cruise control, make use of the system
at speeds above 25 mph (40 km/h).



CONTROL THE USE OF YOUR
ELECTRICAL EQUIPMENT

Before moving off, if the passenger
compartment is too warm, ventilate it by
opening the windows and air vents before using
the air conditioning.
Above 30 mph (50 km/h), close the windows
and leave the air vents open.
Remember to make use of equipment that can
help keep the temperature in the passenger
compartment down (sun roof and window
blinds...).
Switch off the air conditioning, unless it has
automatic digital regulation, as soon as the
desired temperature is attained.
Switch off the demisting and defrosting
controls, if not automatic.
Switch off the heated seat as soon as possible.

Switch off the headlamps and front foglamps
when the level of light does not require their
use.
Avoid running the engine before moving off,
particularly in winter; your vehicle will warm
up much faster while driving.

As a passenger, if you avoid connecting
your multimedia devices (fi lm, music, video
game...), you will contribute towards limiting
the consumption of electrical energy, and so
of fuel.
Disconnect your portable devices before
leaving the vehicle.














































ECO-DRIVING

Eco-driving is a range of everyday practices that allow the motorist to optimise their fuel consumption and CO2 emissions.

01030 23070 190110 150250 50
210
90170130
0.
5
1.5
2.53.5
4.5
12
65 4 3tr/min
x1000km/h
50 01/2
190
130
CHECK/000
22

















PETROL - DIESEL MANUAL
OR AUTOMATIC GEARBOX
INSTRUMENT PANELS


DIALS



1.
Rev counter.

Indicates the speed of rotation of the engine (x 1 000 rpm).

2.
Coolant temperature.

Indicates the temperature of the engine coolant (° Celsius).

3.
Fuel level.

Indicates the quantity of fuel remaining in the tank.

4.
Vehicle speed.

Indicates the current speed of the moving vehicle (mph or km/h).

5.
Small display screen.


6.
Central display screen.


7.
Display management button.

Starts a manual CHECK.
Recalls the service information.
Resets the selected function to zero (trip distance recorder or
service indicator).

8.
Lighting rheostat button.

Adjusts the brightness of the lighting of the instruments and
controls.

With large central display screen


Panel. grouping together the vehicle operation indication dials and
warning lamps, with permanent back-lighting.
For more information, refer to the paragraph relating to the button
or function and its associated display.


With small central display screen

1/
INSTRUMENTS AND CONTROLS

Vehicle parameters

This menu allows you to activate or deactivate certain driving and
comfort equipment:


- vehicle speed repeat,

- selective unlocking (refer to the "Access" section),

- guide-me-home and welcome lighting (refer to the "Visibility" and
"Ergonomics and Comfort" sections),

- interior mood lighting (refer to the "Ergonomics and Comfort" section),

- daytime running lamps (refer to the "Visibility" section),

- directional headlamps (refer to the "Visibility" section),

- rear parking sensors (refer to the "Driving" section).



Choice of language

This menu allows you to select the language used by the display:
Deutsch, English, Espanol, Français, Italiano, Nederlands, Portugues,
Portugues-Brasil, Türkçe * .


Choice of units

This menu allows you to select the units: temperature (°Celsius or
°Fahrenheit) and fuel consumption (l/100 km, mpg or km/l).


*
According to country.
Main menu
Vehicle parameters
Choice of language
Choice of units
ESC

30










Operation indicator lamps

If one of the following indicator lamps comes on, this confi rms that the
corresponding system has come into operation.
It may be accompanied by an audible signal.
Depending on your version of instrument panel, illumination of the
indicator lamp may also be accompanied by:


- a pictogramme in the central instrument panel screen and a
message in the multifunction screen,
or

- a pictogramme and a message in the central instrument panel
screen.




Warning lamp



is on



Cause



Action/Observations








Left-hand
direction
indicato
r


fl ashing with
buzzer. The lighting stalk is pushed
down.






Right-hand
direction indicator



fl ashing with
buzzer. The lighting stalk is pushed up.







Hazard warning
lamps


fl ashing with
audible signal. The hazard warning lamps
switch, located on the dashboard,
has been operated. The left-hand and right-hand direction indicators and their
associated indicator lamps fl ash simultaneously.





Sidelamps


fi xed. The lighting stalk is in the
"Sidelamps" position or the
"AUTO" position with low light.




Dipped beam
headlamps


fi xed.

The lighting stalk is in the "Dipped beam
headlamps" position or in the "AUTO"
position in conditions of low light.




Main beam
headlamps


fi xed. The lighting stalk is pulled
towards you. Pull the stalk again to return to dipped beam headlamps.

00.5
16
7
60
6
12
93
55
50
45
40
353025
20
15
1
0
5
38









LIGHTING DIMMER

Permits manual adjustment of the brightness of the instruments and
controls to suit the ambient light level. Only operates when the vehicle
lighting is on, with the exception of the daytime running lamps.

Activation



)
Press the button to change the brightness of the instruments and
controls.

)
When the lighting reaches the minimum setting, release the button,
then press again to increase it.
or


)
When the lighting reaches the maximum setting, release the button,
then press again to reduce it.

)
When the lighting reaches the level of brightness required, release
the button.



Deactivation

When the vehicle lighting is off, or in day mode on vehicles fi tted with
daytime running lamps, pressing the button does not have any effect.

















CLOCK

The analogue clock, located between the central vents of the
dashboard, does not have an adjustment button.
To set the time, refer to the section relating to your multifunction
screen's confi guration menu.
The clock is synchronised with the multifunction screen time; once the
the setting has been confi rmed on the multifunction screen, the hands
will turn to synchronise with the screen, and each time the ignition is
switched on.

42




















MONOCHROME SCREEN C (WITH
PEUGEOT CONNECT SOUND)

DISPLAYS ON THE SCREEN

This displays the following information:


- time,

- date,

- ambient temperature (this fl ashes if there is a risk of ice),

- state of the openings (doors, boot...),

- visual parking sensors.

- audio functions,

- telephone information and directories.
Warning messages (e.g.: "Emission control system faulty") or
information messages (e.g.: "Automatic lighting of headlamps
activated") may appear temporarily. These can be cleared by pressing
the "ESC"
button.


CONTROLS

From the control panel of your Peugeot Connect Sound, you can:


)
press the "MENU"
button for access to the main menu
,

)
press the " 
" or " 
" buttons to scroll through the items on the
screen,

)
press the "MODE"
button to change the permanent application
(audio source, telephone...),

)
press the " 
" or " 
" buttons to change a setting value,

)
press the "OK"
button to confi rm,
or


)
press the "ESC"
button to abandon the operation in progress.

11:32104.6 FM1RTL23Mem1c°
TMC LOUD RDS TATue 21/10/2010

44

"PERSONALISATION-CONFIGURATION"
MENU
Once this menu has been selected, you can gain access to the
following functions:


- defi ne the vehicle parameters,

- display confi guration,

- choice of language.


Define the vehicle parameters

Once this menu has been selected, you can activate or deactivate the
following equipment:


- selective unlocking (refer to the "Access" section),

- guide-me-home and welcome lighting (refer to the "Visibility" and
"Ergonomics and Comfort" sections),

- interior mood lighting (refer to the "Ergonomics and Comfort" section),

- daytime running lamps (refer to the "Visibility" section),

- rear parking sensors (refer to the "Driving" section).
)
Press the " 
" or " 
" buttons, then the "OK"
button to select the
"Guide-me-home headlamps" line.

)
Press the " 
" or " 
" buttons to set the value required (15, 30 or
60 seconds), then press the "OK"
button to confi rm.

)
Press the " 
" or " 
" buttons, then the "OK"
button to select the
"OK"
box and confi rm or press the "ESC"
button to cancel.
Example: setting of the duration of the guide-me-home lighting


)
Press the " 
" or " 
" buttons, then the "OK"
button to select the
menu required.