2011 Peugeot iOn radio

i
!
Driving
52










Starting - stopping the vehicle
- Position 1 : LOCKThe steering is locked.
- Position 2 : ACCThe ancillaries (radio, 12 V socket...) canbe used.
- Position 3 : ON
Ignition on.
- Position 4 : STA RT"Ready" lamp on. Motor ready to drive the vehicle.
Ignition switch
)
Inser t the key in the ignition switch.
)
Turn the key to position 4 (START).


Starting
Stopping
)Immobilise the vehicle.
)Place the drive selector in position P.P)Turn the key to position 1 (LOCK).)Remove the key from the ignition switch.)Hold it in this position for a few seconds until the"READY" lampcomes on accompanied by an
audible signal.
) Release the key.
The key returns automatically to position 3 (ON).
Key in ignition
If the key has been left in the ignition, an
audible signal is heard on opening the driver's door.

Do not attach any heavy objects to the key as this could weigh down on it whenin the ignition switch and cause a fault.

If you use the ancillaries for a prolongedperiod (with the key in the ACCposition), you risk discharging the ancillaries battery. Star ting your vehicle will then no longer be possible. Be aware .

8
!
i
Practical information
89
Do not charge the battery without firstdisconnecting the terminals. Do not disconnect the terminals whenthe "Ready" lamp is on, nor when thevehicle is being charged.
Before disconnecting
You must wait 2 minutes after switchingoff the ignition before disconnecting the battery.


Batteries contain harmful substancessuch as sulphuric acid and lead. Theymust be disposed of in line with legal requirements and never put out withhousehold waste. Ta k e used batteries to an authorisedcollection point.
)Disconnect the negative (-) terminal.)Lift the protective cover on the (+)terminal 2.)Slacken nut 3.)Disconnect the positive (+) terminal. )Remove the battery.)Charge the battery following the
instructions given by the manufacturer of
the battery charger. )Reconnect the battery starting with the (+) cable.

After reconnecting

After reconnecting the battery, switchon the ignition and wait 1 minute
before star ting, to allow initialisation of the electronic systems. However, if minor problems persist after doingthis, contact a PEUGEOT dealer or a qualified workshop.Remember to enter the radio code yourself, referring to the relevant section.

Ensure that the battery posts and cable terminals are clean. If they are coveredwith sulphates (whitish or greenish deposit), disconnect and clean them.

i
!i
Practical information
112
"Protection":
front and rear mudflaps, vehicle cover,
translucent bumper protectors, side rubbing strips...
"Multimedia":
audio systems, speed camera warning,
universal solar charger...

The fitting of electrical equipment or accessories which are not recommended by PEUGEOT may result
in a failure of your vehicle's electronicsystem and excessive electricalconsumption. Please note this precaution. You are advised to contact a PEUGEOTrepresentative to be shown the range of recommended equipment and accessories.
Installation of radiocommunicationtransmitters
Before installing any after-market radio communication transmitter, you cancontact a PEUGEOT dealer for thespecification of transmitters which canbe fitted (frequency, maximum power,aerial position, specific installation requirements), in line with the VehicleElectromagnetic Compatibility Directive(2004/104/EC).



Depending on the legislation in forcein the country, it may be compulsory to have a high visibility safety vest, warning triangle and spare bulbs andfuses available in the vehicle.

127
The system is coded in such a way that it will only
operate in your vehicle. If it is to be installed in another
vehicle, contact your PEUGEOT dealer for confi guration
of the system.

AUDIO SYSTEM/BLUETOOTH

01 First steps


For safety reasons, the driver must only carry out
operations which require prolonged attention while the
vehicle is stationary.
When the motor is switched off and to
prevent
discharging of the battery, the audio system may switch off after a few minutes.



CONTENTS

02 Radio

03 Audio

04 Using the telephone

05 Audio settings

06 Configuration

07 Screen menu map

Frequently asked questions p.
p.
p.
p.
p.
p.
p.
p. 128
129
132
138
144
145
146
147
After a battery disconnection, a code has to be enteredfor operation of the radio.

A maximum of fi ve attempts are possible. For the last
two attempts, a 15 minutes wait is imposed between each attempt.
R
efer to the end of this document to fi nd the label indicating this code:

1
2
74
5
6
3
8
9
7
01
128
FIRST STEPS
1. On/Off and volume adjustment.
2. CD e
ject.
3. Selection of source:
FM1, FM2, CD, USB, AUX, Streamin
g.
Accept an incoming call.
Long press:


- access to calls lo
g of the telephoneconnected,

- or end a call in pro
gress.
4.
Selection of a preset radio station.
Radio: lon
g press: preset a radio station.

Other than radio: see relevant sections.

5. Displa
y the list of stations received, theCD/USB tracks or folders.
Lon
g press: update the list of stationsreceived.

6. Abandon current operation.
Up one level
(menu or folder). 7. Automatic search
for a lower/higher radio
frequency.
Selection of
previous/next CD, USB track.
Navigation in a list.
Maintained press:
fast forwards or backwards.
8. Main menu.
9. Audio settings:
e
qualizer, treble, bass, loudness,
distribution, left/right balance, front/rear
balance, automatic volume.

11
02
1
2
129
RADIO
Press SRC/TEL several times insuccession and select the FM1 or FM2radio band.
Press a button to listen to the corresponding preset station.
Select the desired radio station and confi rm by pressing "OK".







RADIO

Press LIST
to display the list of stations
received in alphabetical order.
The exterior environment
(hills, buildings, tunnel, car park, below ground...) may prevent reception, even in RDS station tracking mode. Thisphenomenon is normal in the propagation of radio waves and is in no way indicative of a fault with the audio system.

A long press on LIST
builds or updates
the list of stations; audio reception is cut
momentarily.
Make a lon
g press on one of the buttons
to preset the station being heard.
The name of the station is displayedaccompanied by an audible signal to confi rm the preset.

A press chan
ges to the next or previous
letter (e.g. A, B, D, F, G, J, K, ...). MANAGE THE LIST
PRESETTING AND SELECTING A STATION

1
2
02
1
2
130
RDS, if displayed, enables you to continue listening to the same station by automatic retuning to alternative frequencies. However,
in certain conditions, coverage of an RDS station may not be assured throughout the country as radio stations do not cover
100 % of the territory. This explains the loss of reception of thestation during a journey.

RADIO


RDS


When the radio is displayed in thescreen, press MENUthen select "Radio" .

Select or deselect "RDS"
to activate or deactivate RDS then confi rm with "OK"
to save the setting.


ENTER A FREQUENCY MANUALLY
Press MENU
, select "Radio"
, thenselect "Write freq."
.
Pr
ess + or -r to select the desired
frequency and confi rm with "OK".

1
2
02
1
131
RADIO

Radio text is information transmitted by the radio station related to
the current programme or song.

With the radio displayed on the screen, press MENUthen select "Radio".


Select or deselect "TXT" to activate or deactivate the display of Radio Text.



DISPLAY RADIO TEXT






RECEIVING TA MESSAGES


The TA (Traffi c Announcement) function gives priority to TA alert messages. To operate, this function needs good reception of a
radio station transmitting this type of message. When a traffi c
report is transmitted, the current audio source (Radio, CD,USB, ...) is interrupted automatically to play the TA message.
Normal playback of the audio source resumes at the end of the
transmission of the message.

Pr
ess MENU, select "Radio", then select or deselect "TA"
to activate or deactivate the reception of traffi cmessages.