Page 93 of 164
8
i
!
Practical information
91
1.12 V compressor with integral pressure gauge, to measure and adjust the tyre
pressure.
Composition of the kit
2.Sealant car tridge for the temporary repair
of a tyre.3.Injection pipe. 4.Suction pipe, to remove the sealantproduct if necessary:
5.Sachet containing a replacement valve core, a tool for removing/refitting the valve core and a speed restriction sticker.
The speed restriction sticker must beaffixed to the vehicle's steering wheel toremind you that a wheel is in temporary use.
Do not exceed a speed of 50 mph(80 km/h) when driving with a tyre repaired using this type of kit.
Refi tting the rear seat cushion
)Put the metal cover back into place. )Refit the four "butterfly" screws. )Insert the metal hooks into the seat backrest. )Fold the seat cushion down until it locks in place.
When refitting the cushion, take care not to trap the seat belt buckles.
Page 94 of 164
!
i
Practical information
92
Repair procedure
1. Sealing
)Switch off the ignition. )Indicate on the speed restriction sticker provided, the wheel to be repaired, then fix it to the steering wheel as a reminder that a
wheel is in temporary use. )Shake the sealant car tridge, remove the cap and screw on the injection pipe.
) Remove the valve cap for the tyre to be
repaired. ) Remove the valve core using the tool
provided, and store in in a clean place.
) Connect the injection pipe to the valve of
the tyre to be repaired.
)Tap the sealant car tridge (top down)several times with your hand, so as to
inject all of the product into the tyre. )Remove the injection pipe. )Refit the valve core and tighten it usingthe tool provided.
Take care, this product is harmful (e.g. ethylene-glycol, colophony...) if swallowed andcauses irritation to the eyes.Keep it out of reach of children. The use-by date of the sealant is marked on the car tridge.
After use, do not discard the empty cartridge but take it to a PEUGEOT dealer (France) or
an authorised waste disposal site. Don't forget to obtain a replacement cartridge; they are available from a PEUGEOT dealer or a qualified workshop.
Avoid removing any foreign bodieswhich have penetrated into the tyre.
Page 95 of 164
8
!
i
Practical information
93
2. Infl ation
)Check that the compressor switch A
is in
the "OFF" position. )Uncoil the compressor pipe B.
)
Connect this pipe to the valve of the
repaired wheel. )
Connect the compressor's electric plug to
the vehicle's 12 V socket (ignition switch in
position "ON" or "ACC"). ) Star t the compressor by turning the
switch A
to the "ON"position. )
Using the compressor, adjust the pressure in accordance with the vehicle's tyre
pressure label (located in the driver's door
aperture).
A loss of pressure indicates that the
puncture has not been fully plugged;contact a PEUGEOT dealer or a qualified
workshop for assistance.
) Remove the compressor and stow the kit. )
Drive off straight away at reduced speed (50 mph [80 km/h] max) limiting thedistance travelled to approximately
120 miles (200 km).
As soon as possible, go to a PEUGEOT dealer or a qualified workshop. Tell the technician that you have used the kit. After checking, the technicianwill advise you whether the tyre can berepaired or must be replaced.
If after around 5 to 7 minutes the pressure is not attained, this indicates that the tyre is not repairable; contacta PEUGEOT dealer or a qualifiedworkshop for assistance.
Page 96 of 164
i
Practical information
94
Changing a wheel
- A jack: for lifting the vehicle.
- A wheelbrace: for removin
g and refitting
the wheel bolts.
- A handle: for operating the jack.
These tools are not supplied with your vehicle.
Parking the vehicle
Immobilise the vehicle where it does notblock traffic: the ground must be level,stable and not slippery. Apply the parking brake, switch off the ignition and put the drive selector in
position Pto lock the wheels.
If necessary, place a chock under thewheel diagonally opposite the wheel to be changed.
You must ensure that the occupants get out of the vehicle and wait where they are safe. Never go underneath a vehicle raised using a jack; use an axle stand.
Page 97 of 164
8
Practical information
95
)Slacken the bolts using the wheelbrace. )Place the jack in contact with one of the
two front A or rear B
locations provided on
the underbody, whichever is closest to the
wheel to be changed.
Removing the wheel
) Using the handle, extend the jack until its base plate is in contact with the ground.
Ensure that the centreline of the jack base
plate is directly below the location A or Bused. )
Raise the vehicle until there is sufficientspace between the wheel and the ground.
)
Remove the bolts and store them in a clean place. )
Remove the wheel.
Page 98 of 164
i
Practical information
96
Fitting the wheel
)Put the wheel in place on the hub. )Screw in the bolts by hand. )Pre-tighten the bolts using the wheelbrace.
) Lower the vehicle fully. )
Fold the jack and detach it. )Tighten the bolts using the wheelbrace.
After changing a wheel
Have the tightening of the bolts andthe pressure of the new wheel checked by a PEUGEOT dealer or a qualifiedworkshop without delay.
Page 103 of 164
8
Practical information
101
Changing a dipped beamheadlamp bulb
)Turn the bulb holder to the left andpull it out. )Remove the bulb by pressing its tab. )Replace the bulb.
To r efit, carry out these operations in reverse order.
Changing a foglamp/daytime running lamp bulb
)
Turn the wheels onto full lock to improveaccess. )
Remove the clips holding the protective cover over the bulb holder. )
Pull the cover away.
)
Turn the bulb holder ( Afor the foglamp, Bfor the daytime running lamps) to the left
and pull it out.
) Pull the bulb out and replace it.
To r e f i t , c a r ry out these operations in reverseorder.
Page 112 of 164
i !
!
Practical information
110
Towing the vehicle
Procedure for having your vehicle towed using fixed mechanical equipment.
To w i ng your vehicle
The towing eye is welded to the body below thefront bumper. )
Install the towing bar. )
Start your vehicle ("Ready" lamp on). )
Put the drive selector in position N . )
Release the parking brake. )
Switch on the hazard warning lamps onyour vehicle. )
Have your vehicle towed for no more than 20 miles (30 km) without exceeding a
speed of 20 mph (30 km/h) .
When towing the vehicle with the four wheels on the ground, always use a towing bar.
When towing with only two wheels onthe ground, use professional lifting equipment.
Failure to follow these instructions may cause damage to braking components and the electric motor.
Changing a wiper
blade
Removing a front or rear
wiper blade
)Raise the corresponding wiper arm. )Remove the wiper blade, sliding it towards
the outside.
Fitting a front or rear wiper
blade
)Put the new wiper blade in place and
secure it. )Fold down the wiper arm carefully.
To w i ng another vehicle
Your vehicle cannot be used in any circumstances to tow another vehicle.
