Page 124 of 340
122
!
Driving
)
Press 1
, the speed limiter mode is
activated but remains paused.
You do not have to switch the speed limiter
on in order to set the speed.
)
Set the speed value by pressing
button 2
or 3
(e.g.: 55 mph (90 km/h)).
Programming
Exceeding the programmed speed
Pressing the accelerator pedal to exceed the programmed speed will
not have any effect unless you press the pedal firmly
past the point of
resistance
.
The speed limiter is deactivated temporarily and the programmed
speed, which is still displayed, flashes.
Returning to the programmed speed, by means of intentional or
unintentional deceleration of the vehicle, automatically cancels the
flashing of the programmed speed.
Off/Return to normal
driving
)
Press 5
, the speed limiter is deactivated.
On a steep descent or in the event of
sharp acceleration, the speed limiter will
not be able to prevent the vehicle from
exceeding the programmed speed.
The use of mats not approved by
PEUGEOT may adversely affect the
normal operation of the accelerator
pedal and impede the operation of the
speed limiter.
Mats approved by PEUGEOT have a
third fixing in the area of the pedals to
avoid any risk of inter ference with the
pedals.
In the event of a speed limiter fault, the speed
is cleared resulting in flashing of the dashes.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
Operating fault
You can then change the programmed speed using buttons 2
and 3
:
- by + or - 1 mph (km/h) = shor t press,
- by + or - 5 mph (km/h) = long press,
- in steps of + or - 5 mph (km/h) = maintained press.
)
Switch the speed limiter on by pressing button 4
.
)
Suspend the speed limiter by pressing button 4
: the screen
confirms the suspension with "Pause".
)
Switch the speed limiter back on by pressing button 4
again.
Page 125 of 340
4
123
i
i
Driving
Cruise control
System which automatically maintains the
speed of the vehicle at the value programmed
by the driver, without any action on the
accelerator pedal.
The cruise control is switched on
manually: it
requires a minimum vehicle speed of 25 mph
(40 km/h) and the engaging:
- 4th gear or higher on a manual gearbox,
- 2nd gear or higher on an electronic gear
control gearbox or automatic gearbox,
- position A
on the electronic gear control
gearbox or D
on the automatic gearbox.
The cruise control is switched off
manually
or by pressing the brake or clutch pedal or
on triggering of the ESP system for safety
reasons.
It is possible to exceed the programmed speed
temporarily by pressing the accelerator pedal.
To return to the programmed speed, simply
release the accelerator pedal.
Switching off the ignition cancels any
programmed speed value.
1.
Cruise control mode selection button
2.
Speed programming/programmed value
decrease button
3.
Speed programming/programmed value
increase button
4.
Cruise control suspension/resume button
(pause)
5.
Cruise control off button
Steering mounted controls
The cruise control cannot, in any
circumstances, replace the need to
obser ve speed limits, nor can it replace
the need for vigilance and responsibility
on the par t of the driver.
This information also appears in the
head-up display.
For more information on the head-up
display, refer to the relevant page in this
"Driving" section. The programmed information is grouped
together in the instrument panel screen.
Displays in the instrument panel
A.
Cruise control on/pause indication
B.
Cruise control mode selection indication
C.
Programmed speed value
Page 126 of 340
124
!
Driving
)
Press 1
, the cruise control is activated
but remains paused.
)
Set the programmed speed by
accelerating to the required speed, then
press button 2
or 3
(e.g.: 70 mph
(110 km/h)).
Programming
You can then change the programmed speed using buttons 2
and 3
:
- by + or - 1 mph (km/h) = shor t press,
- by + or - 5 mph (km/h) = long press,
- in steps of + or - 5 mph (km/h) = maintained press.
)
Pause the cruise control by pressing button 4
: the screen confirms
the suspension with with "Pause".
)
Switch the cruise control back on by pressing button 4
again.
Exceeding the programmed speed
Intentional or unintentional exceeding of the programmed speed results
in flashing of this speed on the display.
Return to the programmed speed, by means of intentional or unintentional
deceleration of the vehicle, automatically cancels the flashing of the speed. When the cruise control is switched on,
be careful if you maintain the pressure
on one of the programmed speed
changing buttons: this may result in a
very rapid change in the speed of your
vehicle.
Do not use the cruise control on
slippery roads or in heavy traffic.
On a steep descent, the cruise control
will not be able to prevent the vehicle
from exceeding the programmed speed.
To avoid any risk of jamming of the
pedals:
- ensure that the mat is positioned
correctly,
- never fit one mat on top of another.
In the event of a cruise control fault, the speed
is cleared resulting in flashing of the dashes.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
Operating fault
Off/Return to normal driving
)
Press 5
; cruise control mode is deactivated The screen returns to
the distance recorder.