Page 50 of 340
48
!
Access
System which protects and provides a deterrent
against theft and break-ins. It provides the
following types of monitoring:
Alarm
- Exterior perimeter
The system checks for opening of the vehicle.
The alarm is triggered if anyone tries to open a
door, the boot or the bonnet...
- Interior volumetric
The system checks for any variation in the
volume in the passenger compartment.
The alarm is triggered if anyone breaks a
window, enters the passenger compar tment or
moves inside the vehicle.
- Tilt
The system checks for any change in the
attitude of the vehicle.
The alarm is triggered if the vehicle is lifted,
moved or knocked.
Self-protection function
The system checks for the putting out of
ser vice of its components.
The alarm is triggered if the battery, the
central control unit or the wires of the
siren are put out of ser vice or damaged.
For all work on the alarm system,
contact a PEUGEOT dealer or a
qualified workshop.
Locking the vehicle with full
alarm system
Activation
)
Switch off the ignition and get out of the vehicle.
)
Press the locking button on the
remote control or lock the vehicle
using the Keyless Entry and
Star ting system. The monitoring system is active: the indicator
lamp on the button flashes once per second.
After the locking button on the remote control
is pressed or the vehicle locked using the
Keyless Entry and Star ting system, the exterior
perimeter monitoring is activated after a delay
of 5 seconds and the interior volumetric and
anti-tilt monitoring after a delay of 45 seconds.
If an opening (door, boot...) is not closed
fully, the vehicle is not locked but the exterior
perimeter monitoring will be activated after a
delay of 45 seconds at the same time as the
interior volumetric and anti-tilt monitoring.
)
Press the unlocking button on
the remote control or unlock the
vehicle using the Keyless Entry
and Star ting system.
Deactivation of the volumetric
monitoring
The volumetric protection system is
deactivated: the indicator lamp in the
button goes off.
Page 51 of 340
2
49
Access
Locking the vehicle
with exterior perimeter
monitoring only
Deactivate the interior volumetric and anti-lift
monitoring to avoid unwanted triggering of the
alarm in cer tain cases such as:
- leaving a window par tially open,
- washing your vehicle,
- changing a wheel,
- having your vehicle towed,
- transpor tation by sea.
Deactivation of the interior
volumetric and anti-tilt monitoring
)
Switch of the ignition and within
ten seconds, press this button
until the indicator lamp is on
continuously.
)
Get out of the vehicle.
)
Press the locking button on
the remote control immediately
or lock the vehicle using the
Keyless Entry and Star ting
system.
The exterior perimeter monitoring alone is
activated: the indicator lamp in the button
flashes once per second.
To be effective, this deactivation must be carried
out each time the ignition is switched off.
Reactivation of the interior
volumetric and anti-tilt monitoring
Tr i g g e r i n g o f t h e a l a r m
This is indicated by sounding of the siren and
flashing of the direction indicators for thirty seconds.
The monitoring functions remain active until
the alarm has been triggered eleven times in
succession.
)
Press the unlocking button on
the remote control or unlock the
vehicle using the Keyless Entry
and Starting system to deactivate
the exterior perimeter monitoring.
)
Press the locking button on the
remote control or lock the vehicle
using the Keyless Entry and
Starting system to activate all the
monitoring functions.
The indicator lamp in the button
again flashes once per second.
When the vehicle is unlocked using
the remote control or unlocked
using the Keyless Entry and Star ting
system, rapid flashing of the indicator
lamp in the button informs you that the alarm
was triggered during your absence. When
the ignition is switched on, this flashing stops
immediately.
Failure of the remote control
To deactivate the monitoring functions:
)
Unlock the vehicle using the key in the
driver's door lock.
)
Open the door; the alarm is triggered.
)
Switch on the ignition; the alarm stops. The
indicator lamp in the button switches off.
Locking the vehicle without
activating the alarm
)
Lock or deadlock the vehicle using the key
in the driver's door lock.
Operating fault
When the ignition is switched on, fixed
illumination of the indicator lamp in the button
indicates a fault in the system.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
*
According to country.
Automatic activation *
2 minutes after the last door or the boot is
closed, the system is activated automatically.
)
To avoid triggering the alarm on entering
the vehicle, first press the unlocking button
on the remote control or unlock the vehicle
using the Keyless Entry and Star ting
system.
Page 54 of 340
52
Access
Boot
Saloon
)
After unlocking the vehicle completely
using the remote control or the key, press
this button.
SW
)
After unlocking the vehicle completely
using the remote control or the key, press
at the top (on lever A
), and raise the
tailgate.
From the inside
Hold this button down until unlocking of the
boot is heard.
Opening
Closing
)
Lower the tailgate using the interior grab
handle.
If the tailgate is not closed correctly:
- when the engine is running
,
this warning lamp and a
message in the instrument panel
screen appear for a few seconds,
- when the vehicle is moving
(speed above
6 mph (10 km/h)), this warning lamp and
a message, accompanied by an audible
signal, appear in the instrument panel
screen for a few seconds.
Page 57 of 340
2
55
Access
Emergency release
(Saloon and SW)
System for mechanical unlocking of the boot in
the event of a battery or central locking fault.
Unlocking
)
Fold back the rear seats to gain access to
the lock from inside the boot.
)
Inser t a small screwdriver into hole A
of the
lock to unlock the tailgate.
"Boot open" warning
With the engine running or when the vehicle is
moving, if the tailgate is not properly closed,
a message accompanied by an audible signal
(from 6 mph (10 km/h)) is displayed in the
instrument panel screen.
Page 68 of 340
66
!
Comfort
Rear seats
Bench seat the left-hand (1/3) or right-hand (2/3) section of which can be folded to adapt the boot load space.
Rear head restraints
These have a high position (comfor t and safety)
and a low position (rear visibility).
They can also be removed.
To remove a head restraint:
)
pull the head restraint fully upwards,
)
then, press the lug A
.
Never drive with rear passengers when
the head restraints are removed; the
head restraints must be in place and in
the high position.
Folding the seat from the
boot (SW)
Each section of the bench seat (1/3 or 2/3) has
its own control to release the seat back and its
seat cushion from the boot.
)
Check that nothing is preventing the seat
back from folding (head restraint, seat
belts, ...),
)
check also that no object on or under the
seat could hinder its movement,
)
pull the control from the boot and push the
seat backrest.
Page 75 of 340
3
73
i
Comfort
Peugeot Connect USB
This connection box, consisting of a JACK
auxiliary socket and a USB port, is located in
the front armrest (under the cover).
It permits the connection of por table device,
such as a digital audio player of the iPod
® type
or a USB memory stick.
It reads the audio file formats (MP3, OGG,
WMA, WAV, ...) which are transmitted to your
audio equipment and played via the vehicle's
speakers.
You can manage these files using the steering
mounted controls or the audio system control
panel and display them in the instrument panel
screen.
When the USB por t is used, the por table device
charges automatically.
For more information on the use of
this system, refer to the "Audio and
Telematics" section.
Ski flap
Device for storing and transpor ting long
objects.
Opening
)
Lower the armrest.
)
Press the flap opening control.
)
Lower the flap.
)
Load the objects from inside the boot.
Page 76 of 340
74
Comfort
Boot fi ttings (Saloon)
1.
Retractable hooks
2.
Storage trays
With towing eye, a wheel chock and a
temporary puncture repair kit (according to
destination country and equipment).
3.
Stowing rings
4.
Retaining straps
5.
Boot lamp
6.
Boot floor
For access to the storage compar tments or
the spare wheel (according to destination
country), raise the floor .
7.
Adjustable divider
Page 77 of 340
3
75
Comfort
Boot fi ttings (SW)
1.
Boot lamps
2.
Rear seats folding controls
3.
Retractable hooks
4.
12 V accessor y socket (120 W max)
5.
Storage
trays
With towing eye, a wheel chock and a
temporary puncture repair kit (according to
destination country and equipment).
6.
Stowing rings
7.
Load space cover
(see following page) .
8.
Boot floor
For access to the storage compar tments or the
spare wheel (according to destination country),
position the floor ver tically in its guide.
