2011 Peugeot 508 boot
[x] Cancel search: bootPage 79 of 340
3
77
!
i
Comfort
Warning triangle (stowing)
Before leaving your vehicle to set up
and install the triangle, put on your high
visibility vest.
The dimensions of the triangle (once folded) or
its storage box must be:
- A
: length = 438
mm,
- B
: height = 56
mm,
- C
: width = 38
mm.
To use the triangle, refer to the manufacturer's
instructions.
Saloon
)
Press the lug 1
and pull the assembly
towards you.
SW
)
Turn the knob 2
to remove the cover.
)
Hold the cover and the triangle so that they
do not fall.
The location for a folded triangle is in the inner
trim panel of the boot lid.
Placing the triangle in the road
)
Place the triangle at a distance behind
the vehicle, as shown in the table below,
according to the type of road and the level
of ambient light.
Distance from your vehicle (in metres)
Road
Motorway
Day
Night
50 m
80 m
150 m
These are the internationally recognised
values.
Use the triangle in line with local driving
regulations.
The triangle is available as an accessory,
contact a PEUGEOT dealer or a qualified
workshop.
Page 83 of 340
3
81
i
Comfort
In order for these systems to be fully effective, follow the operation and maintenance
guidelines below:
)
If the interior temperature remains very high after the vehicle has been parked in the sun
for a considerable time, first ventilate the passenger compartment for a few minutes.
Place the air flow control at a sufficient level to provide an adequate renewal of air in the
passenger compartment.
)
To obtain an even air distribution, take care not to obstruct the exterior air intake grilles
located at the base of the windscreen, the nozzles, the vents and the air outlets, as well
as the air extractor located in the boot.
)
Use in preference the intake of exterior air as prolonged use of the air recirculation may
cause misting of the windows and side windows.
)
Do not cover the sunshine sensor, located on the dashboard; this is used for regulation
of the automatic air conditioning system.
)
Operate the air conditioning system for 5 to 10 minutes, once or twice a month to keep it
in good working order.
)
Ensure that the passenger compartment filter is in good condition and have the filter
elements replaced regularly (refer to the "Checks" section).
We recommend the use of a combined passenger compartment filter. Thanks to its second special
active filter, it contributes to the purification of the air breathed by the occupants and the cleanliness
of the passenger compartment (reduction of allergic symptoms, bad odours and greasy deposits).
)
The air conditioning uses power from the engine while operating. This results in an
increase in the vehicle's fuel consumption.
When towing at or near maximum capacity or on steep slopes in high ambient temperatures,
switching off the air conditioning saves engine power and so improves towing capacity.
Condensation created by the air conditioning results in a discharge of water under the
vehicle when stationary, which is per fectly normal.
)
To ensure correct operation of the air conditioning system, you are also advised to have
it checked regularly.
)
If the system does not produce cold air, do not use it and contact a PEUGEOT dealer or
a qualified workshop.
Recommendations for ventilation and air conditioning
The air conditioning system does not
contain chlorine and does not present
any danger to the ozone layer.
Page 101 of 340
4
99
!
Driving
Emergency braking
In the event of a failure of the main ser vice
brake or in an exceptional situation (e.g. driver
taken ill, under instruction, etc) a continuous
pull on the control lever A
will stop the vehicle.
The electronic stability programme (ESP)
provides stability during emergency braking.
If the emergency braking malfunctions, the
message "Parking brake control faulty" will be
displayed.
If a failure of the ESP system is
signalled by the lighting of this
warning lamp, then braking stability is
not guaranteed.
In this event, stability must be assured by the
driver by repeating alternate "pull-release"
actions on the control lever A
.
Emergency parking brake release
)
if your vehicle has one, take out the vehicle
chock B
, located under the boot floor.
)
On a slope, immobilise the vehicle by
placing a chock in front or behind one of
the front wheels, opposing the slope.
On level ground, immobilise the vehicle by
placing a chock in front or behind one of
the front wheels. In the event of fault with the electric parking
brake or a battery failure, an emergency
mechanical control can be used to manually
release
the parking brake.
)
Immobilise the vehicle (or chock it if the
brake pedal has not been released), with
the engine running, by engaging first gear
(manual gearbox, position P
(automatic
gearbox) or M
or R
(electronic gear control
gearbox).
)
Switch of the engine, but leave the ignition
on. If you are unable to immobilise the
vehicle, do not operate this control and
contact a PEUGEOT dealer or a qualified
workshop as soon as possible.
The emergency braking must only be
used in exceptional circumstances.
Page 139 of 340
5
137
i
!
Visibility
Manual adjustment
of halogen
headlamps
Automatic adjustment of xenon headlamps
To avoid causing a nuisance to other road
users, the height of the halogen headlamps
should be adjusted according to the load in the
vehicle.
0.
1 or 2 people in the front seats.
-.
5 people.
1
Intermediate setting.
5 people + maximum authorised load in the
boot.
2
Driver + maximum authorised load in the
boot.
-
Not used.
3
Not used.
If a fault occurs, this
warning lamp is displayed
in the instrument panel,
accompanied by an audible signal and a
message in the instrument panel screen.
The system then places your headlamps in the
lowest position. In order to avoid causing a nuisance to other
road users, this system corrects the height of the
xenon headlamps beam automatically and when
stationary, in relation to the load in the vehicle.
If a fault occurs, do not touch the xenon
bulbs. Contact a PEUGEOT dealer or a
qualified workshop.
The initial setting is position "0"
.
Page 143 of 340
5
141
!
Visibility
Rear wiper
If a significant accumulation of snow or
ice is present, or when using a bicycle
carrier on the boot, deactivate the
automatic rear wiper via the instrument
panel screen configuration menu. Rear wiper selection ring: park,
intermittent wipe,
wash-wipe (set duration).
Reverse gear
When reverse gear is engaged, the rear wiper
will come into operation if the windscreen
wipers are operating.
The function is activated or
deactivated via the instrument panel
screen configuration menu.
This function is activated by default.
Programming
)
Pull the windscreen wiper stalk towards
you. The windscreen wash then the
windscreen wipers operate for a fixed
period.
The headlamp washers only operate when the
dipped beam headlamps are on
.
Windscreen and headlamp
wash
Screenwash/headlamp wash
level low
In the case of vehicles fitted
with headlamp washers, when
the fluid reser voir low level
is reached this warning lamp comes on in the
instrument panel, accompanied by an audible signal
and a message in the instrument panel screen.
The warning lamp comes on when the ignition is
switched on, or every time the stalk is operated,
until the reser voir is refilled.
Next time you stop, refill the screenwash/headlamp
wash reservoir.
Page 172 of 340
170
Practical information
This kit is installed in the storage box,
under the boot floor. Complete system consisting of a compressor
and a sealant car tridge which permits
temporary repair
of a tyre so that you can
drive to the nearest garage.
It is designed to repair most punctures which
could affect the tyre, located on the tyre tread
or shoulder.
Temporary puncture repair kit
Access to the kit
List of tools
All of these tools are specific to your vehicle
and can vary according to equipment. Do not
use them for other purposes.
1.
12 V compressor.
Contains a sealant cartridge for the
temporary repair of a tyre and can also be
used for adjusting tyre pressures.
2.
One chock * to block one of the front wheels
of the vehicle.
3.
Removable towing eye.
See "Towing the vehicle".
* Depending on destination country or equipment.
Page 178 of 340
176
Practical information
Changing a wheel
Procedure for changing a faulty wheel for the spare wheel using the tools provided with the vehicle.
The tools are installed in the boot under the
floor.
To gain access to them:
)
open the boot,
)
position the floor ver tically (SW: in its
guide) for access to the tools.
Access to the tools
List of tools
All of these tools are specific to your
vehicle and can vary according to the level
of equipment. Do not use them for other
purposes.
1.
Wheelbrace.
For removing the wheel trim and removing
the wheel bolts.
2.
Jack with integral handle.
For raising the vehicle.
3.
"Bolt cover" tool.
For removing the bolt protectors
(covers) on alloy wheels.
4.
Socket for the security bolts (located in the
glove box).
For adapting the wheelbrace to the special
"security" bolts.
5.
One wheel chock for immobilising the
vehicle.
6.
To w i n g e y e .
See "Towing the vehicle".
Page 179 of 340
8
177
i
Practical information
Wheel with trim
When refitting the wheel
, refit the trim
star ting by placing its notch facing the
valve and press around its edge with
the palm of your hand.
The spare wheel is installed in the boot under
the floor.
According to country, the spare wheel may be
steel, alloy or of the "space-saver" type.
To gain access to it, refer to the paragraph
"Access to the tools" on the previous page.
Access to the spare wheel
Taking out the wheel
)
Unscrew the yellow central bolt.
)
Raise the spare wheel towards you from
the rear.
)
Take the wheel out of the boot.
Depending on your vehicle's equipment, the
spare wheel is secured either by a strap or a
central bolt. For the bolt, the procedure is given
below.