2011 NISSAN GT-R buttons

Black plate (72,1)
Model "R35-N" EDITED: 2009/ 10/ 30
3. Highlight [Add Destination] or [Add Way-point] and push .4. The system starts calculating a route that
includes the added destination or waypoint.
When the calculation is finished, the route is
displayed.
INFO:
. If a waypoint was added, [More Routes]
cannot be selected. .
If a destination was added, the prior
destination becomes a waypoint.
Moving location of destinationThe location of the destination can be adjusted
by moving the cross pointer across the map.1. Highlight [Move Location] and push TER>.
INFO:
The screen for adjusting the location also
changes by touching the map screen dis-
played on the right side of the screen.
2. Adjust the location by moving the cross pointer across the map and push TER>. The location of the destination is
modified.
INFO:
Even if the map screen is touched or the
directional buttons other than the up or down
button are operated, the same map screen as
when [Move Location] is selected is displayed.
2-46
Navigation

Black plate (77,1)
Model "R35-N" EDITED: 2009/ 10/ 30
.Turn listThe list screen for showing the guide points to
the destination and the map screen can be
displayed at the same time. An enlarged
intersection view is automatically displayed
when the vehicle approaches the guide point.
The turn list can be scrolled using the center
dial, the main directional buttons or by touching
the up/down buttons on the screen.
Push

Black plate (86,1)
Model "R35-N" EDITED: 2009/ 10/ 30
Confirming routeWhen the suggested route is displayed after
calculation, the route information can be con-
firmed or the suggested route can be simulated.Basic operation:1. Push .
2. Highlight [Route Info] and push .3. Highlight the preferred item and push
. Available setting items
.
[Turn List]:
Displays the details of the suggested route.
“Using turn list” page 2-60
. [Preview]:
The system will trace the planned route
going forward or in reverse.“Using route preview” page 2-61
. [Simulation]:
Displays a simulation of the suggested
route. This function provides a detailed
image of the route with voice guidance.“Confirming route by simulation” page
2-61
. [Store Route]:
Stores a calculated route. A maximum of 5
routes can be stored. Stored routes can be
easily retrieved and set as the suggested
route.“STORING ROUTE” page 2-74
. [Map Scroll]:
Displays a map screen where the location of
the destination can be confirmed.
Even if the map screen is touched or
directional buttons other than the up or
down button are pushed, the same map
screen as when [Map Scroll] is selected is
displayed.
Using turn list:1. Highlight [Turn List] and push .
2. The information (e.g., intersections) can be confirmed on the route to the destination by
scrolling the screen using the up and down
switches of the main directional buttons or
the center dial.
3. Push

Black plate (96,1)
Model "R35-N" EDITED: 2009/ 10/ 30
7. The icon displayed on the map screen isswitched, and the travel time to the waypoint
is displayed.
Displayed icon
:Displayofthetraveltimetothe
destination:Displayofthetraveltimetothewaypoint
Set average speedsThe required time to the destination can be
calculated based on the set vehicle speeds.1. Push .
2. Highlight [Navigation] and push .
3. Highlight [Guidance Settings] and push .
4. Highlight [Others] and push .
5. Highlight [Set Average Speeds] and push .
6. Highlight the preferred item and push .
7. Use the main directional buttons or the center dial to make an adjustment. The
speed can be increased/decreased by 5
MPH (5 km/h) .
8. After finishing the setting, push or
to activate the setting.
9. Push to return to the previous
screen. Push

Black plate (97,1)
Model "R35-N" EDITED: 2009/ 10/ 30
[].
. [Town Road]:
Adjust the average vehicle speed on a town
road by moving the main directional buttons
or the center dial in the direction of [+] or
[].
. [Residential]:
Adjust the average vehicle speed in a
residential area by moving the main direc-
tional buttons or the center dial in the
direction of [+] or [ ].
. [Reset]:
Sets the average vehicle speeds to the
default values.
STORING LOCATIONOften visited locations can be stored in the
Address Book. The stored addresses can be
easily retrieved to set them as a destination or
waypoint.
INFO:
. The Address Book can store up to 300
locations.
. New information placed in the same storage
position will overwrite the old data.
Storing location by searchingAfter a location is searched for once, it can be
stored for future use.
1. Push .2. Highlight [Navigation] and push .
3. Highlight [Address Book] and push TER>.4. Highlight [Stored Location] and push TER>.
Navigation
2-71
STORING A LOCATION/ROUTE

Black plate (139,1)
Model "R35-N" EDITED: 2009/ 10/ 30
XM satellite radio band select:
Pushingwill change the band as
follows:
XM1 ?XM2 ?XM3 ?XM1
When or is pushed while
the ignition switch is in the ACC or ON position,
the radio will come on at the channel last played.
The last channel played will also come on when
the ON·OFF button is pushed to ON.
The satellite radio is not available in Alaska,
Hawaii and Guam.
If another audio source is playing when
or is turned to ON, the
audio source will automatically be turned off and
the last radio channel played will come on.
When the stereo broadcast signal is weak, the
radio will automatically change from stereo to
monaural reception.TUNE (Tuning):. For AM and FM radio
Turn the radio TUNE knob for manual tuning.
. For XM Satellite Radio
Turn the radio TUNE knob to seek channels
from all of the categories when any category
is not selected.
SEEK tuning/CATEGORY (CAT):.For AM and FM radio
Push <
>or <
>to tune from low to
high or high to low frequencies and to stop
at the next broadcasting station.
. For XM Satellite Radio
Push <
>or <
>to tune to the first
channel of the next or previous category.
During satellite radio reception, the following
notices will be displayed under certain condi-
tions.
. NO SIGNAL (No signal is received while the
SAT tuner is connected.)
. OFF AIR (Broadcasting signed off)
. CHECK ANTENNA (Antenna connection
error)
. LOADING (When the initial setting is
performed)
. UPDATING (When the satellite radio sub-
scription is not active)
SCAN tuning:
Push to tune from low to high
frequencies and stop at each broadcasting
station/channel for 5 seconds. Pushing the
button again during this 5 seconds period will stop SCAN tuning and the radio will remain
tuned to that station/channel.
If
is not pushed within 5 seconds,
SCAN tuning moves to the next station/channel.
*1
to
*6
Station memory operations:
12 stations/channels can be set for the FM band
(6 each for FM1 and FM2) , 18 for XM radio (6
each for XM1, XM2 and XM3) and 6 stations
can be set for the AM band.
1. Choose the radio band using the radio band select button.
2. Tune to the desired station/channel using <
>, <
>, or the radio
TUNE knob.
3. Push and hold the desired station preset button
*1
to*6
until the radio mutes.
4. The station indicator will then come on and the sound will resume. Memorizing is now
complete.
5. Other buttons can be set in the same manner.
If the battery cable is disconnected, or if the fuse
opens, the radio memory will be erased. In that
case, reset the desired stations/channels.
Audio system
3-13

Black plate (152,1)
Model "R35-N" EDITED: 2009/ 10/ 30
.Albums
. Songs
. Podcasts
. Genres
. Composers
. Audiobooks
. Shuffle Songs
The following touch-panel buttons shown on the
screen are also available:
.
: returns to the previous screen.
.: plays/pauses the music selected.
Next/Previous Track and Fast Forward/
Rewind:When <
>or <
>is pushed for more
than 1.5 seconds while the iPod
®is playing, the
iPod
®will play while fast forwarding or rewind-
ing. When the button is released, the iPod
®will
return to the normal play speed.
When <
>or <
>is pushed for less
than 1.5 seconds while the iPod
®is playing, the
next track or the beginning of the current track
on the iPod
®will be played.
The center dial can also be used to select tracks
when the iPod®is playing.
REPEAT (RPT) , RANDOM (RDM):
When is pushed while a track is
being played, the play pattern can be changed
as follows:MUSIC BOXThe “Music Box” audio system can store songs
from CDs being played. The system has a 9.3
gigabyte (GB) storage capacity and can record
up to 200 hours (approximately 2,900 songs) .
The following CDs can be recorded in the
“Music Box” audio system.
. CDs that contain uncompressed audio files
. Hybrid Compact Disc Digital Audio (Hybrid
CD-DA) specification in Super Audio CDs
. Compact Disc Digital Audio (CD-DA) spe-
cification in CD-Extras
. First session of multisession disc Extreme temperature conditions [below

48 F( 20 8C) and above 158 8F (70 8C)] could
affect the performance of the hard-disk.
NOTICE
If the audio system needs to be re-
placed due to a malfunction, all stored
music data will be erased.Recording CDs1. Operate the audio system to play a CD.
“Compact Disc (CD) player operation”
page 3-14
2. Select [Start REC].
NOTICE
. The system starts playing and re-
cording the 1st track on the CD
when [Start REC] is selected.
3-26
Audio system

Black plate (13,1)
4 Bluetooth®
Hands-Free Phone System
Model "R35-N" EDITED: 2009/ 10/ 30
Bluetooth ®
Hands-Free Phone System ................... 4-2
Regulatory information ..................................... 4-3
Voice commands. ........................................... 4-3
Control buttons ............................................. 4-4
Connecting procedure ..................................... 4-4
Phone selection ............................................. 4-4 Vehicle phonebook
......................................... 4-4
Making a call ................................................. 4-6
Receiving a call ............................................. 4-7
During a call ................................................. 4-7
Phone setting ................................................ 4-8