2011 MITSUBISHI OUTLANDER Headlight

Vehicle care and maintenance
7-53
7
NOTE
The side turn signal light (on outside rearview mirror) use
an LED instead of the bulb. Check with an authorized
Mitsubishi Motors dealer or repair facility of your choice
when either light needs to be repaired or replaced.

It is not possible to repair or replace only the bulb for the
side turn signal light (on fender).
Check with an authorized Mitsubishi Motors dealer or a
repair facility of your choice when the light needs to be
repaired or replaced.
NOTE
The tail and stop light and the high-mounted stop light use
an LED instead of the bulb. Check with an authorized
Mitsubishi Motors dealer or repair facility of your choice
when either light needs to be repaired or replaced.
WA R N I N G
!
Check with an authorized Mitsubishi Motors dealer
or a repair facility of your choice when it is neces-
sary to repair a high intensity discharge headlight or
to replace the bulb.
The power circuit, bulb and electrodes generate high
voltages that may cause a severe shock.
Item
Wa t t a g e
ANSI trade No.
or bulb type
8 - High-mounted stop light — —
9 - License plate light 5 W W5W
10 - Back-up light 21 W 7440
11 - Tail and stop light — —
12 - Rear side-marker light 5 W W5W
13 - Rear turn signal light 21 W WY21W
BK0122500US.book 53 ページ ２０１０年５月１２日　水曜日　午前１１時１１分

Vehicle care and maintenance
7-55
7
Headlights (low beam, except for vehicles
equipped with high intensity discharge head-
lights)
N00901800033
1. When replacing the bulb on the driver’s side (3.0 liter
models only) remove the bolt (A) holding down the relay
box and move the relay box toward the rear of the vehicle. 2. Turn the bulb (B) counterclockwise to remove it.*- Front of the vehicle
*- Front of the vehicle
BK0122500US.book 55 ページ ２０１０年５月１２日　水曜日　午前１１時１１分

7-56 Vehicle care and maintenance
7
3. While holding down the tab (C), pull out the socket (D).
4. To install the bulb, perform the removal steps in reverse.
CAUTION
!
Handle halogen light bulb with care. The gas inside
a halogen light bulb is highly pressurized, so drop-
ping, knocking, or scratching a halogen light bulb
can cause it to shatter.
Never hold the halogen light bulb with a bare hand,
dirty glove, etc.
The oil from your hand could cause the bulb to
break the next time the headlights are used.
If the glass surface is dirty, clean it with alcohol and
let it dry completely before installing the bulb.
BK0122500US.book 56 ページ ２０１０年５月１２日　水曜日　午前１１時１１分

Vehicle care and maintenance
7-57
7
Headlights (high beam, except for vehicles
equipped with high intensity discharge head-
lights)
N00901900034
1. Turn the cap (A) counterclockwise to remove it.2. Turn the bulb (B) counterclockwise to remove it.*- Front of the vehicle
*- Front of the vehicle
BK0122500US.book 57 ページ ２０１０年５月１２日　水曜日　午前１１時１１分

7-58 Vehicle care and maintenance
7
3. While holding down the tab (C), pull out the socket (D). 4. To install the bulb, perform the removal steps in reverse.
CAUTION
!
Handle halogen light bulb with care. The gas inside
a halogen light bulb is highly pressurized, so drop-
ping, knocking, or scratching a halogen light bulb
can cause it to shatter.
Never hold the halogen light bulb with a bare hand,
dirty glove, etc.
The oil from your hand could cause the bulb to
break the next time the headlights are used.
If the glass surface is dirty, clean it with alcohol and
let it dry completely before installing the bulb.
BK0122500US.book 58 ページ ２０１０年５月１２日　水曜日　午前１１時１１分

Vehicle care and maintenance
7-59
7
Daytime running lights (for vehicles equipped
with high intensity discharge headlights)
N00902000032
1. Turn the cap (A) counterclockwise to remove it.2. Turn the socket (B) counterclockwise to remove it.*- Front of the vehicle
*- Front of the vehicle
BK0122500US.book 59 ページ ２０１０年５月１２日　水曜日　午前１１時１１分

7-60 Vehicle care and maintenance
7
3. Turn the bulb counterclockwise while pressing it and pull
it out of the socket.
4. To install the bulb, perform the removal steps in reverse.
Headlights (low/high beam, for vehicles equipped
with high intensity discharge headlights)
N00900300073
Do not attempt to disassemble or repair headlights, and do not
attempt to replace their bulbs.Adjustment of headlight aim
N00943200121
The alignment of the headlights should be checked by an
authorized Mitsubishi Motors dealer or a repair facility of your
choice.
WA R N I N G
!
A high voltage is present in the power circuit and in
the bulbs and bulb terminals. To avoid the risk of an
electric shock, contact an authorized Mitsubishi
dealer whenever repair or replacement is necessary.
BK0122500US.book 60 ページ ２０１０年５月１２日　水曜日　午前１１時１１分

Alphabetical index
4Genuine parts 1-8
Glove compartment 3-273
H
Hazard warning flasher switch 3-221
Hazard warning lights 3-206
Head restraints 2-26
Headlight leveling switch 3-219
Headlights
Bulb capacity 7-51
Dimmer 3-216
Headlight flasher 3-217
Replacement 7-55
,7-57
Switch 3-212
High beam indicator 3-206
High mount stop light
Bulb capacity 7-51
Hill start assist 3-128
Hood lock release mechanism and safety catch 7-41
Horn switch 3-233
I
If the vehicle breaks down 6-2
Ignition switch 3-25
,3-86
Important facts to know in case of an accident 8-5
Indicators 3-206
Information screen display 3-160
,3-194
Inside rearview mirror 3-82Inspection and maintenance following rough road operation 3-
124
Instrument cluster 3-157
Interior lights 3-268
J
Jack 6-7
Storage 6-7
Jump-starting the engine 6-2
K
Keyless entry system 3-9
,3-45
Keys 3-2
L
Labeling 9-2
License plate light
Bulb capacity 7-51
Replacement 7-73
Link System 3-233
Loading information 4-8
Lubricants 9-11
Luggage floor box 3-279
Luggage hooks 3-286
M
Malfunction indicator light 3-207
Manual air conditioning 5-6
,5-16
MIVEC engine 3-33
,3-41
,3-91
BK0122500US.book 4 ページ ２０１０年５月１２日　水曜日　午前１１時１１分