2011 MITSUBISHI OUTLANDER change language

6
What does a\f\f this stu\b do?
1) Digital Cl\b\fk
t ime is displayed when the ignition\: key is in the ON or ACC position. t o set the time, press and hold the CLOCK [1] button until the display
flashes. t o change the hour, press the H [2] button. t o change the minutes, press the M [3] button.
once you have made your adjustments to the hours and min\:utes, then press the [1] button once more to lock in the time.
2) Multi-Inf\brmati\bn Meter (INFO) Butt\bn
t he info button changes display information for warnings, odometer/tripmeter, service reminder, engine coolant temperature, average
and momentary fuel c\:onsumption, driving \:range and average speed. it is also possible to change elements su\:ch as the language \:and units
used on the multi\bin\:formation display by pushing the multi\b\:information meter (INFO) button.
3) A\ftive Stability C\bntr\bl (ASC) OFF Butt\bn
t his system automatically turns on when the ignition switch is turned to the ON position. to deactivate the ASC, press the ASC OFF button
for 3 seconds or longer. t o reactivate the ASC, press the ASC OFF button again. mitsubishi motors recommends that the ASC normally be
kept in the ON position. f or more information, refer to your owner’s manual.
4) Rhe\bstat Meter Illuminati\bn Butt\bn
t he brightness of the instrument panel can be \:adjusted by pressing the button.
5) P\bwer Seat Adjustment (if equipped)\w
t he power seat controls are located on the bottom left side of the \:driver’s seat.
TO ADJUST THE SET FORWARD OR BACKWARD: Push the switch in the desired direction [1].
TO ADJUST THE SEAT BACK: Push the switch in the desired direction [2].
TO RAISE OR LOWER THE FRONT END OF\w SEAT: Raise or lower the front part of the switch.
TO RAISE OR LOWER THE REAR END OF S\wEAT: Raise or lower the rear part of the switch.
TO RAISE OR LOWER THE ENTIRE SEAT: Raise or lower the center of the switch.
11
2
123

7
6) P\bwer Outlet (if equip\wped)
12 V POWER OUTLETS:
TYPE 1: l ocated in the floor console and the lugg\:age compartment. a ccessories can be operated when the ignition\: switch is in either
the ON or ACC position.
TYPE 2: l ocated in the floor console box. a ccessories can be operated in all ignition \:switch positions.
7) Sunr\b\bf (if equipped)
TO OPEN: Push the switch in the desired direction [1]
TO CLOSE: Push the switch in the desired direction [3]
TO TILT UP: Push the switch [2]
TO TILT DOWN: Push the switch to the direction [3]
8) Heated Seats (if equipped)
t he heated seat controls are located at the side of each f\:ront seat. t he heated seats can be operated by pushing the switch when the
ignition switch is in the ON position. t he indicator light will illum\:inate while the heater is on.
9) Drive M\bde Sele\ft\br (if equipped)
t he drive mode can be switched by turning the dial \:while the ignition \:switch is in the ON position. t he following drive modes are
available:
2WD: t his mode is for economical driving on\: normal dry roads and freeways.
4WD AUTO: t he default mode. t his mode is for all driving conditions on various roads.
4WD LOCK: t his mode is for driving in slippery\: conditions such as \:on snow\bcovered roads or sand.
10) Multi-Inf\brmati\bn Display (if equipped)
t he multi\binformation display shows fuel remaining, outside t\:emperature, selector lever position, all\bwheel drive operation
status, etc. it is also possible to change elements su\:ch as the language \:and units by using the multi\bi\:nformation meter (INFO)
button. t he display screen is different depending on whet\:her the ignition switch is in the OFF or ON position.
1
3
2