2011 MERCEDES-BENZ SPRINTER warning

Instrument cluster variants
Function Page
0046
Instrument cluster on
vehicles without
steering-wheel buttons
70
0047
Indicator and warning
lamps
008A
0069, 006A Brightens/dims the
instrument cluster lighting 72
0088
Tachometer with indicator
and warning lamps
71
0086
Display 73
0087
Fuel gauge with fuel filler
flap location indicator
72
006E
Speedometer with
indicator and warning
lamps
71
006F
Reset button 0048
70
0070
007B Menu button:
• changes standard display 73
• selects menus 73 Function Page
0071
Instrument cluster on
vehicles with steering-
wheel buttons
70
0072
Indicator and warning
lamps
0073
Display 74
0074
Tachometer with indicator
and warning lamps
71
0075
Fuel gauge with fuel filler
flap location indicator
72
0076
0069, 006A Brightens/dims the
instrument cluster lighting 72
0077
Speedometer with
indicator and warning
lamps
71
0078
Reset button 0048
70
0079
00A4 Service button
Checks the engine oil level 171
Indicator and warning
lamps24
Instrument cluster variants
At a glance

Function Page
0067
ESP
®
warning lamp 50,
187 ASR warning lamp 48,
187 0041
Coolant level too low 193
00AE
Coolant temperature too
high
193
008A
Restraint systems
malfunction
191
0065
Brake fluid level too low 188
EBD malfunction 187
Trailer brake force booster
malfunction
188
00B4
Engine oil level warning 192
00BB
Engine diagnostics
indicator lamp
194
Exhaust gas aftertreatment
malfunction
195
0028
Preglow system 194
004A
Left-hand turn signal 90
0077
Tire pressure loss or the tire
pressure monitor is
malfunctioning (USA only)
195
Tire pressure loss (Canada
only)
195
00BD
Fluid level too low in
windshield washer/
headlamp cleaning system
196
003E
Door open 197
0026
Brake pads/linings worn 191
004D
Right-hand turn signal 90
0031
ABS malfunction 189
003D
ASR malfunction 189
BAS malfunction 189
009E
ESP
®
malfunction 187 Function Page
00E4
DEF supply low or
contaminated/thinned
199
Exhaust gas aftertreatment
malfunction
200
00AB
Dirt accumulation in air
filter
195
00B6
Reserve fuel 193
Fuel filler cap open 194
00BA
Water in the fuel 196
003F
Battery charging
malfunction
191
0055
Bulb defective 197
0066
Parking brake applied 112
0064
Low-beam headlamps on 89
004E
Working speed governor
(ADR) on
117
0063
High-beam headlamps on 90
0080
Reserve fuel 193
Fuel filler cap open 194
0082
Fasten seat belt 196
i
Vehicles with steering-wheel buttons:
Corresponding messages may also be
shown in display 0073(Y page 24). Instrument cluster variants
25At a glance

Switch units
Center console
Function Page
0072
Switches the left/right-
hand seat heating on/off
68
0087
Switches the windshield
heating on/off
95
0073
Switches the rear window
defroster on/off
95
0069
Activates/deactivates
PARKTRONIC
122
003B
Switches the hazard
warning lamps on/off
91
00E3
Activates/deactivates ASR 48
00BF
00C0
Central locking, interior/
rear compartment
54 Roof
Function Page
0046
Microphone for the
telephone
134
0047
Switches the right-hand
reading lamp on/off
92
008A
Switches the automatic
interior lighting on/off
92
0088
• Eyeglasses compartment
or 131
• Anti-theft alarm system
(ATA)
61
0086
Switches the interior
lighting on/off
92
0087
Switches the left-hand
reading lamp on/off
92Switch units
27
At a glance

Vehicle equipment
i Diese Betriebsanleitung beschreibt alle
Modelle, Serien- und
Sonderausstattungen
Ihres Fahrzeugs, die zum Zeitpunkt des
Redaktionsschlusses dieser
Betriebsanleitung erhältlich waren.
Länderspezifische Abweichungen sind
möglich. Beachten Sie, dass Ihr Fahrzeug
nicht mit allen beschriebenen Funktionen
ausgestattet sein könnte. Dies betrifft auch
sicherheitsrelevante Systeme und
Funktionen. Occupant safety
Restraint systems
In this section you will learn the most
important facts about the restraint system
components of the vehicle.
The restraint systems are:
R Seat belts
R Child restraint systems
R LATCH-type (ISOFIX) child seat securing
system
Additional protection potential

is provided by
SRS (Supplemental Restraint System) and
the air bag system.
The protective functions of the systems work
in conjunction with each other. The systems
are, however, autonomous. G
Warning
Modifications to or work improperly
conducted on restraint system components
or their wiring, as well as tampering with
interconnected electronic systems, can lead
to the restraint

systems no longer functioning
as intended.
Air bags or Emergency Tensioning Devices
(ETDs), for example, could deploy
inadvertently or fail to deploy in accidents
although the deceleration threshold for air
bag deployment is exceeded. Therefore,
never modify the restraint systems. Do not tamper with electronic components or their
software.
i More information on the subject of
children in the vehicle and child restraint
systems can be found in the "Children in
the vehicle" section (Y
page 41).
Seat belts
Important safety notes The use of seat belts and infant or child
restraints is required by law in all 50 states,
the District of Columbia, the U.S. territories
and all Canadian provinces.
Even if this is not the case, all vehicle
occupants should have their seat belts
fastened when the vehicle is in motion.
i
See "Children in the vehicle"
(Y page 41) for further information on
infants and children

traveling in the vehicle
as well as on child restraint systems. G
Warning!
Always fasten
your seat belt before driving off.
Always make sure all of your passengers are
properly restrained. You

and your passengers
should always wear seat belts.
Failure to wear and properly fasten and
position your seat belt greatly increases your
risk of injuries and their likely severity in an
accident.
If you are ever in an accident, your injuries can
be considerably more severe without your
seat belt properly buckled. Without your seat
belt buckled, you are much more likely to hit
the interior of the vehicle or be ejected from
it. You can be seriously injured or killed.
In the same crash, the possibility of injury or
death is lessened if you are properly wearing
your seat belt. The air bags can only protect
as intended if the occupants are properly
wearing their seat belts. 32
Occupant safety
Safety

G
Warning
Never ride in a moving vehicle with the seat
backrest in an
excessively reclined position as
this can be dangerous. You could slide under
the seat belt in a collision. If you slide under
it, the seat belt would apply force at the
abdomen or neck. That could cause serious
or even fatal injuries. The seat backrest and
seat belt provide the best restraint when the
wearer is in a position that is as upright as
possible and the seat belt is properly
positioned on the body. G
Warning
Never let
more people ride in the vehicle than
there are seat belts available. Make sure
everyone riding in the vehicle is correctly
restrained with a separate seat belt. Never
use a seat

belt for more than one person at a
time. G
Warning
Damaged seat belts or seat belts that have
been subjected to

stress in an accident must
be replaced and their anchoring points must
also be checked.
Only use seat belts which have been approved
by the distributor named on the inside of the
front cover.
Do not make any modifications to the seat
belts. This can lead to unintended activation
of the ETDs or to their failure to activate when
necessary.
Do not bleach or dye seat belts as this may
severely weaken them. In a crash they may
not be able to provide adequate protection.
Have all work carried out only by qualified
technicians. Contact an authorized Sprinter
Dealer. Proper use of the seat belts G
Warning
USE SEAT BELTS PROPERLY
R Seat belts can only protect when used
properly. Never wear

seat belts in any other
way than as described in this section, as
that could result in serious injuries in case
of an accident.
R Each occupant should wear their seat belt
at all times, because seat belts help reduce
the likelihood of and potential severity of
injuries in accidents, including rollovers.
The integrated restraint system includes
SRS (driver's front air bag, front-passenger
front air bag, side impact air bags, window
curtain air bags for door windows),
Emergency Tensioning Devices, seat belt
force limiters, and front seat knee bolsters.
The system is designed to enhance the
protection offered to properly belted
occupants in certain frontal (front air bags
and ETDs) and side (side impact air bags,
window curtain air bags, and ETDs) impacts
which exceed preset deployment
thresholds and in certain rollovers (window
curtain air bags and ETDs).
R Never wear the shoulder belt under your
arm, across your neck or not routed across
your shoulder. In a frontal crash, your body
would move too far forward. That would
increase the chance of head and neck
injuries. The seat belt would also apply too
much force to the ribs or abdomen, which
could severely injure internal organs such
as your liver or spleen.
Adjust the seat belt so that the shoulder
section is located as close as possible to
the middle of the shoulder. It should not
touch the neck. Never pass the shoulder
portion of the seat belt under your arm. For
this purpose, you can adjust the height of
the seat belt outlet.
R Position the lap belt as low as possible on
your hips and not across the abdomen. If
the lap belt is positioned across your Occupant safety
33
Safety
Z

abdomen, it could cause serious injuries in
a crash.
R Never wear seat belts over rigid or
breakable objects in or on your clothing,
such as eyeglasses, pens, keys etc., as
these might cause injuries.
R Make sure the seat belt is always routed
snugly. Take special care of this when
wearing loose clothing.
R Never use a seat belt for more than one
person at a time. Do not fasten a seat belt
around a person and another person or
other objects at the same time.
R Seat belts should not be worn twisted. In a
crash, you would not have the full width of
the seat belt to distribute impact forces.
The twisted seat belt against your body
could cause injuries.
R Pregnant women should also always use a
lap-shoulder belt. The lap belt portion
should be positioned as low as possible on
the hips to avoid any possible pressure on
the abdomen.
R Place the seat backrest in a position that is
as upright as possible.
R Check your seat belt during travel to make
sure it is properly positioned.
R Never place your feet on the instrument
panel, dashboard, or on the seat. Always
keep both feet on the floor in front of the
seat.
R When using a seat belt to secure infant
restraints, toddler restraints, or children in
booster seats, always follow the child seat
manufacturer's instructions. G
Warning
Do not pass seat belts over sharp edges. They
could tear.
Do not allow the seat belt to get caught in the
door or in the seat adjustment mechanism.
This could damage the seat belt.
Never attempt to make modifications to seat
belts. This could impair the effectiveness of
the seat belts. Fastening seat belts G
Warning
According to accident statistics, children are
safer when properly restrained on the rear
seats than on the front-passenger seat. Thus,
we strongly recommend that children be
placed in the rear seat whenever possible.
Regardless of seating position, children 12
years old and under must be seated and
properly secured in an appropriately sized
child restraint system or booster seat
recommended for the size and weight of the
child. For additional information, see the
"Children in the vehicle" section.
A child's risk of serious or fatal injuries is
significantly increased if the child restraints
are not properly secured in the vehicle and/
or the child is not properly secured in the child
restraint.
X Adjust the seat and move the backrest to
an almost vertical position ( Y
page 63). X
Pull the seat belt smoothly through belt
sash guide 0046.34
Occupant safety
Safety

X
Without twisting it, place the shoulder
section of the seat belt over the center of
the shoulder and the lap section across the
hips.
X Engage belt tongue 0047 in buckle 0088.
X If necessary, adjust the seat belt to the
appropriate height ( Y
page 35).
X If necessary, pull upwards on the shoulder
section of the seat belt to tighten the belt
across your body.
All seat belts in the vehicle, except the
driver's seat
belt, are equipped with a special
seat belt retractor to secure child restraint
systems properly. For further information on
"Special seat belt retractors", see
(Y page 43).
For more information about releasing the seat
belt with release button 0088, see "Releasing
seat belts" ( Y page 35).
Adjusting the seat belt height
You can adjust the seat belt height on the
driver's seat and the outer co-driver's seat.
Adjust the belt to a height that allows the
upper part

of the seat belt to be routed across
the center of your shoulder. X
To raise: slide belt sash guide 0046 upwards.
The belt sash guide engages in various
positions. X
To lower: press and hold belt sash guide
release 0086.
X Slide belt sash guide 0046
downwards.
X Release belt sash guide release 0086 and
make sure that belt sash guide 0046 has
engaged.
Releasing seat belts
X Press release button 008A and guide belt
tongue 0047

back towards belt sash
guide 0046.
! Make sure

that the seat belt retracts fully.
The seat belt or belt buckle may otherwise
become trapped in the door or the seat
adjustment mechanism. This could
damage the door, door trim panels and the
seat belt. Damaged seat belts can no
longer provide the intended degree of
protection and must be replaced. Contact
an authorized Sprinter Dealer.
Belt warning for drivers and co-drivers Regardless of whether the driver's and co-
driver's seat belts have already been
fastened, the 0082 seat belt warning lamp
lights up for six seconds each time the engine
is started. It then goes out once the driver and
the front passenger have fastened their seat
belts.
If the driver's seat belt is not fastened after
the engine is started, an additional warning
tone will sound. The warning tone goes out
after approximately six seconds or once the
driver's seat belt is fastened.
Emergency Tensioning Devices, seat
belt force limiters
If the vehicle is equipped with a driver's front
air bag, the seat belts on the driver's and co-
driver's seats have ETDs.
!
If the front-passenger seat is not
occupied, do not engage the seat belt
tongue in the buckle on the front-
passenger seat. Otherwise, the Emergency Occupant safety
35
Safety Z

Tensioning Device could be triggered in the
event of an accident.
ETDs help remove
slack in the seat belts in an
accident, pulling the seat belt close against
the occupant's body.
ETDs do not correct incorrect seat positions
or incorrectly fastened seat belts.
ETDs do not pull vehicle occupants back
towards the backrest.
If the seat belt is also equipped with a seat
belt force limiter and this is triggered, the
force exerted by the seat belt on the vehicle
occupant is reduced.
The seat belt force limiters are synchronized
with the front air bags, which take on a part
of the deceleration force in an accident. Thus,
the force exerted on the occupant is
distributed over a greater area.
The ETDs can only be triggered if the ignition
is switched on and the restraint systems are
operational, see "SRS warning lamp" .
The ETDs are triggered depending on the type
and severity of an accident:
R in the event of a head-on or rear-end
collision, if the vehicle decelerates or
accelerates rapidly in a longitudinal
direction during the initial stages of the
impact
R in the event of a side impact if the vehicle
decelerates or accelerates rapidly in a
lateral direction and the vehicle is equipped
with side impact air bags and/or window
curtain air bags
R in certain situations, if the system detects
that the vehicle will overturn
If the ETDs are triggered, you will hear a bang
and powder may also be released. In rare
cases the bang may temporarily affect your
hearing. The power emitted is generally not
hazardous to health. The 008A SRS indicator
lamp lights up. G
Warning
Pyrotechnic ETDs that were activated must be
replaced. For your safety, when disposing of the
pyrotechnic ETDs always follow our safety
instructions. These are available at any
authorized Sprinter Dealer.
SRS (Supplemental Restraint System)
Introduction SRS reduces the risk of occupants hitting the
vehicle interior
in

the event of an accident. In
addition, it can reduce the forces the
occupants are subjected to during an
accident.
SRS consists of:
R the 008A SRS indicator lamp
R air bags
R air bag control unit (with crash sensors)
R ETDs for the driver's and co-driver's seat
R seat belt force limiters, for the driver's and
co-driver's seat
008A indicator lamp The SRS system conducts a self-test when
the ignition is switched on and in regular
intervals while the engine is running. This
facilitates detection of system malfunctions.
The 008A SRS indicator lamp in the
instrument cluster comes on when the
ignition is switched on.
It goes out no later than a few seconds after
the engine has been started.
The SRS components are in operational
readiness when
the 008A

SRS indicator lamp
is not lit while the engine is running. G
Warning
The SRS self-check has detected a
malfunction if the 008A SRS indicator lamp:
R does not come on at all
R fails to go out approximately 4 seconds
after the engine was started
R comes on after the engine was started or
while driving36
Occupant safety
Safety