2011 MERCEDES-BENZ R-Class front seats

XAt the same time, reach into recess ;.XLift center console : by recess ;
upwards in the direction of the arrow to
release center console : from anchoring
points =.XRemove center console : from the
vehicle.
i Supporting base ? cannot be removed.
Installing the center console
GWarning
The rear center console must be properly
attached to the rear center console base
when the vehicle is in motion. The rear center
console could otherwise come loose. It could
be thrown around in the vehicle interior,
causing injury to the vehicle occupants
during:
R braking
R vehicle maneuvers
R an accident
You can install the center console in two
different positions. In the foremost position
(position 1) you can extend the cargo
compartment fully ( Y page 251) without
removing the center console.
i The stowage compartment and cup
holder will only be illuminated if the center
console is installed in the rear position
(position 0).
XPosition center console B above
supporting base =.XMount the retainers of center console B
using anchoring points ? (position 1) or
A (position 0) of basic carrier =.XGuide the front part of center console B
downwards in the direction of the arrow to
supporting base =.
Center console B must rest on supporting
base =.XPush the front part of center console B
downwards until you hear center console
B engage in securing rings : (position 1)
or ; (position 0).
Enlarging the luggage compartment
Important safety guidelines
GWarning!
When expanding the cargo volume, always
fully fold the corresponding seats and, if so
equipped, always use the cargo net when
transporting cargo.
Unless you are transporting cargo, the seat
backrests must remain properly locked in the
upright position.
In an accident, during hard braking or sudden
maneuvers, loose items will be thrown around
inside the vehicle. This can cause injury to
vehicle occupants unless the items are
securely fastened in the vehicle.
Always use the cargo tie-down rings.
250Stowage areasLoading, stowing and features
BA 251 USA, CA Edition A 2011; 1; 3, en-USd2sboikeVersion: 3.0.3.52010-04-16T14:31:55+02:00 - Seite 250

GWarning!
Never drive a vehicle with the tailgate open.
Deadly carbon monoxide (CO) gases may
enter vehicle interior resulting in
unconsciousness and death.
To enlarge the cargo compartment, the rear
bench seats of the 2nd and 3rd rows of seats
can be folded forwards separately. You can
enlarge the cargo compartment partially
( Y page 251) or fully ( Y page 251).
Partially enlarging the luggage
compartment (folding forward the
seats in the 3rd row)
XMove the head restraint of the
corresponding seat down fully
( Y page 102).XClamp the seat belt behind retainer ;.XPull release handle : of backrest =
upwards in the direction of the arrow.
Backrest = is released.XFold backrest = slowly forwards.
Seat cushion ? is released and moves
automatically to a vertical position.XFold backrest = forwards into a horizontal
position.
i Loop A can be used to pull the backrests
of the 3rd row of seats upright when the
seats are moved into the original position
( Y page 254).
Fully enlarging the luggage
compartment (folding forward the
seats in the 2nd and 3rd rows)
GWarning!
Folded second-row seats are intended to
serve as a cargo volume expansion in
conjunction with folded third-row seats only.
Do not fold the second-row seats and allow
third-row seat occupants to use folded
second-row seats as a footrest while driving.
Third-row seat occupants must, like all vehicle
occupants, keep both feet on the floor in front
of their seat. Otherwise, occupants could
slide under their seat belt in a collision. If
occupants slide under the seat belt, it would
apply force at the abdomen or neck. That
could cause serious or even fatal injuries. Do
not fold the second-row seats and allow third-
row seat occupants to use folded second-row
seats as a table while driving. Objects placed
on folded second-row seats may come loose
during braking, vehicle maneuvers, or an
accident and be thrown around the vehicle
interior. Objects thrown around the vehicle
interior may cause an accident and/or
serious personal injury.
Stowage areas251Loading, stowing and featuresBA 251 USA, CA Edition A 2011; 1; 3, en-USd2sboikeVersion: 3.0.3.52010-04-16T14:31:55+02:00 - Seite 251Z

! Make absolutely sure that you adhere to
the specified folding order when fully
enlarging the cargo compartment:
R fold down the center seat in the 2nd row
of seats (7-seat vehicles)
R fold down the outer seats in the 2nd row
of seats
R fold down the seats in the 3rd row of
seats
You could otherwise damage the seats.
Folding down the center seat in the 2nd
row of seats
! Close the cup holder in the 2nd row of
seats before folding down the 2nd row of
seats. You could otherwise damage the
seats or cup holder.XLower the head restraint on the center seat
in the 2nd row of seats fully ( Y page 102).XPull release loop : in the direction of the
arrow.XFold backrest ; forwards completely until
it is resting on seat cushion = (armrest
position).
Armrest position
XPull release loop ? in the direction of the
arrow and hold it securely.
The seat is released and folds up.XPress seat A further down until the front
of the seat engages in the trunk floor
position.
Trunk floor position
Folding down the outer seats in the 2nd
row of seats
! If you want to fold the outer seats down
in the 2nd row of seats, the front seats must
not be in the rearmost position. Otherwise,
you could damage the front seats and outer
seats in the 2nd row.
! Close the cup holder in the 2nd row of
seats before folding down the 2nd row of
seats. You could otherwise damage the
seats or cup holder.
XMove the seat concerned in the 2nd row to
its rearmost position ( Y page 103).XRemove the center console for the 2nd row
of seats, if installed ( Y page 249).252Stowage areasLoading, stowing and features
BA 251 USA, CA Edition A 2011; 1; 3, en-USd2sboikeVersion: 3.0.3.52010-04-16T14:31:55+02:00 - Seite 252

Footwell of the 2nd row of seats
There is one cargo tie-down ring : in the
footwell behind the driver’s seat and one in
the footwell behind the front-passenger seat.
Footwell of the 3rd row of seats
Two cargo tie down rings : are located in
the footwell of the 3rd row of seats.
Cargo compartment
There are four cargo tie down rings : in the
cargo compartment.
Mounting hooks
Only use the mounting hooks to secure items
of luggage up to maximum of 9 lbs (4 kg) in
weight.
There is a mounting hook : on each of the
side panels in the cargo compartment.
Luggage compartment cover
Important safety guidelines
! When loading the vehicle, make sure that
you do not stack the load in the cargo
compartment higher than the lower edge of
the side windows. Do not place heavy
objects on top of the cargo compartment
cover.
The cargo compartment cover can be
attached behind the 2nd or 3rd row of seats.
Extending/retracting the luggage
compartment cover
Cargo compartment cover installed behind the 3rd
row of seats
256Stowage areasLoading, stowing and features
BA 251 USA, CA Edition A 2011; 1; 3, en-USd2sboikeVersion: 3.0.3.52010-04-16T14:31:55+02:00 - Seite 256

XTo extend: pull the cargo compartment
cover back by grab handle : and clip it
into retainers ; on the left and right.XTo retract: unhook the cargo compartment
cover from retainers ; on the left and right
and guide it forwards by grab handle :
until it is fully retracted.
Removing/installing the luggage
compartment cover
Cargo compartment cover installed behind the 2nd
row of seats
XTo remove: make sure that cargo
compartment cover ; is rolled up.XPress button :.XMove cargo compartment cover ; to the
left.XRemove cargo compartment cover ;.XTo install: extend cargo compartment
cover ; if you wish to install cargo
compartment cover ; behind the 2nd row
of seats ( Y page 257).
!
You must not install the extensions if you
wish to install the cargo compartment
cover behind the 3rd row of seats. The
cargo compartment cover and side panels
in the cargo compartment could otherwise
be damaged.
XIf installed, remove the protective caps
from the side panels on the 3rd row of seatsif you wish to install cargo compartment
cover ; behind the 2nd row of seats.
Protective cap in the right-hand side panel of the
3rd row of seats
XPush in the bottom of the protective cap as
indicated by the arrow.
The protective cap folds out at the top.XPull the protective cap up from the side
panel in the direction of the arrow.
i Stow the protective caps in a safe place.
XWith the handle of the cargo compartment
pointing to the rear and button : facing
upwards, insert cargo compartment
cover ; into the recess of the side trim on
the left-hand side.XGuide cargo compartment cover ; in front
of the recess on the right.XPress button : and insert the right-hand
side section into the recess of the side trim.XEnsure that the cargo compartment cover
has engaged properly.
Extending the luggage compartment
cover
The cargo compartment cover is equipped
with two extensions that are fastened
securely to the cargo compartment cover
with cords.
You must extend the cargo compartment
cover if you wish to install the cargo
compartment cover behind the 2nd row of
seats.
Stowage areas257Loading, stowing and featuresBA 251 USA, CA Edition A 2011; 1; 3, en-USd2sboikeVersion: 3.0.3.52010-04-16T14:31:55+02:00 - Seite 257Z

XHold extension ? in front of cargo
compartment cover ; with guide pins :
pointing directly at guides =.XTurn extension ? and cargo compartment
cover ; towards each other in the
direction of the arrow.
Guide pins : engage in guides =.
If the extensions are not required, they can
be secured to the cargo compartment cover.
XSlide guide rail : into guide ; to the stop.
Safety net
Important safety guidelines
GWarning!
Make sure the cargo net is properly engaged
at top and bottom position and the tightening
belts are securely fastened.
Never use a damaged cargo net.
Always use cargo net when transporting
cargo. This helps to avoid personal injury from
smaller objects being thrown around in the
occupant compartment during a collision or
sudden maneuver.
The cargo net cannot prevent the movement
of large, heavier objects into the passenger
compartment in an accident. Such items must
be properly secured using the cargo tie-down
rings in the cargo compartment floor.
Passenger use of seats behind installed cargo
net is restricted because of the footwell being
taken up by the net.
When the vehicle is loaded with objects that
extend beyond the seat backrests, using a
cargo net is particularly important. For
reasons of safety, a cargo net should always
be used when transporting cargo.
Preparing the safety net
The cargo net can be used in two different
positions (behind the B-pillar or the C-pillar).
R The brackets behind B-pillar : are
required for the complete cargo
compartment enlargement ( Y page 251).
The corresponding cargo tie down rings
to tighten the net are located in the footwell
of the 2nd row of seats ( Y page 255).
R The brackets behind C-pillar ; are
required for the partial cargo compartment
enlargement ( Y page 251).
The corresponding cargo tie down rings to
tighten the net are located in the footwell
of the 3rd row of seats ( Y page 255).
258Stowage areasLoading, stowing and features
BA 251 USA, CA Edition A 2011; 1; 3, en-USd2sboikeVersion: 3.0.3.52010-04-16T14:31:55+02:00 - Seite 258

XUndo the two Velcro fasteners of the
safety-net stowage.XUnroll and unfold the cargo net.
The upper and lower guide rods must
engage audibly.
Attaching the safety net
Cargo net attached behind the C-pillar
:Retainer;Guide rodXInsert guide rod ; into retainer : in the
direction of the arrow.XSlide guide rod ; forwards into
retainer : in the direction of the arrow.
Tightening the safety net
Seat belt reel holder behind the front seats
XInsert belt hook : into cargo tie-down
ring ; in the direction of the arrow.XPull tensioning strap = by the loose end in
the direction of the arrow until the cargo
net is tight.XAfter driving a short distance, check the
tension of the cargo net and retighten it if
necessary.
Releasing the safety net
Seat belt reel holder behind the front seats
XPull belt adjuster : upwards in the
direction of the arrow to reduce the tension
on the tensioning strap.XUnhook belt hook ; from cargo tie-down
ring =.
Detaching and storing the safety net
XDetach guide rod ; from bracket :
( Y page 259).XPress the red button on the upper and lower
guide rods.XFold the cargo net and roll it up.XClose the two Velcro fasteners on the cargo
net holder.
Roof carrier
Important safety guidelines
GWarning!
Only use the roof rack when the basic carrier
bars have been completely mounted. The left
Stowage areas259Loading, stowing and featuresBA 251 USA, CA Edition A 2011; 1; 3, en-USd2sboikeVersion: 3.0.3.52010-04-16T14:31:55+02:00 - Seite 259Z

insertion and removal or by sockets that do
not fit correctly. A damaged socket can
cause the cigarette lighter to stop working.
Center console, front
XTurn the key to position 2 in the ignition
lock.XOpen cover :(Y page 247).XPress in cigarette lighter ;.
Cigarette lighter ; will pop out
automatically when the heating element is
red-hot.
12 V sockets
Points to observe before use
! If you are using all sockets in the vehicle,
make sure that you do not exceed the
maximum current draw of 55 A. Otherwise,
you will overload the fuses.
The socket can be used for accessories with
a maximum power consumption of 240 W,
e.g. lamps or chargers for mobile phones.
If you use the socket for long periods when
the engine is switched off, the battery may
discharge.
XTurn the key to position 2 in the ignition
lock.Socket in the front-passenger footwell XLift up the cover of socket :.
Socket in the cockpit
!
If accessories are connected, make sure
that a maximum current draw of 15 A is not
exceeded. Otherwise, you will overload the
fuse.
! The socket is not suitable for operating
the electric air pump.
XOpen cover : (Y page 247).XRemove cover ; from the socket.
i
On vehicles with the smoker's package, a
cigarette lighter is installed instead of the
socket ( Y page 264).
Socket in the second row of seats
! If accessories are connected, make sure
that a maximum current draw of 20 A is not
exceeded. Otherwise, you will overload the
fuse.
Features265Loading, stowing and featuresBA 251 USA, CA Edition A 2011; 1; 3, en-USd2sboikeVersion: 3.0.3.52010-04-16T14:31:55+02:00 - Seite 265Z