2011 MAZDA MODEL CX-7 engine

Black plate (422,1)
Body Lubrication
All moving points of the body, such as
door and hood hinges and locks, should
be lubricated each time the engine oil is
changed. Use a nonfreezing lubricant on
locks during cold weather.
Make sure the hood's secondary latch
keeps the hood from opening when the
primary latch is released.
Wiper Blades
CAUTION
ØHot waxes applied by automatic
car washers have been known to
affect the wiper's ability to clean
windows.
ØTo prevent damage to the wiper
blades, do not use gasoline,
kerosene, paint thinner, or other
solvents on or near them.
ØWhen the wiper lever is in the
AUTO position and the ignition is
switched ON, the wipers may
move automatically in the
following cases:
ØIf the windshield above the rain
sensor is touched.
ØIf the windshield above the rain
sensor is wiped with a cloth.
ØIf the windshield is struck with
a hand or other object.
ØIf the rain sensor is struck with
a hand or other object from
inside the vehicle.
Be careful not to pinch hands or
fingers as it may cause injury, or
damage the wipers. When
washing or servicing your Mazda,
make sure the wiper lever is in the
OFF position.
Contamination of either the windshield or
the blades with foreign matter can reduce
wiper effectiveness. Common sources are
insects, tree sap, and hot wax treatments
used by some commercial car washes.
If the blades are not wiping properly,
clean the window and blades with a good
cleaner or mild detergent; then rinse
thoroughly with clean water. Repeat if
necessary.
8-30
Maintenance and Care
Owner Maintenance
CX-7_8BM8-EA-10I_Edition1 Page422
Friday, September 10 2010 4:24 PM
Form No.8BM8-EA-10I

Black plate (436,1)
2. If you are changing the right low-beam
bulb, start the engine, turn the steering
wheel all the way to the right, and turn
off engine. If you are changing the left
low-beam bulb, turn the steering wheel
to the left.
3. Turn the screws and the center section
of the plastic retainers
counterclockwise and remove them,
then partially peel back the mudguard.
InstallationRemoval
4. Detach the electrical connector from
the bulb by pulling it to the rear.
5. Pull off the sealing cover.
6. Unhook the bulb retaining spring.7. Swing the retaining spring out and
away to free the bulb.
Sealing
cover
8. Carefully remove the bulb from the
socket by pulling it straight back.
9. Replace the bulb.
10. Install the new bulb in the reverse
order of removal.
NOTE
lTo replace the bulb, contact an Authorized
Mazda Dealer.
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton for the
replacement bulb to dispose of the old bulb
promptly and out of the reach of children.
8-44
Maintenance and Care
Owner Maintenance
CX-7_8BM8-EA-10I_Edition1 Page436
Friday, September 10 2010 4:24 PM
Form No.8BM8-EA-10I

Black plate (437,1)
Front side marker lights, Front turn
signal lights/Parking lights
1. Make sure the headlight switch is off.
2. If you are changing a bulb in the right
headlight unit, start the engine, turn the
steering wheel all the way to the right,
and turn off the engine. If you are
changing a bulb in the left headlight
unit, turn the steering wheel to the left.
3. Turn the screws and the center section
of the plastic retainers
counterclockwise and remove them,
then partially peel back the mudguard.
InstallationRemoval
4. Turn the socket and bulb assembly
counterclockwise and remove it.
5. Disconnect the bulb from the socket.
Front side marker lights
Front turn signal lights/Parking lights
6. Install the new bulb in the reverse order
of removal.
Fog lightsí
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Loosen the screws securing the fog
light cover.
3. Remove the fog light cover.
4. Loosen the screws securing the fog
light unit.
Maintenance and Care
Owner Maintenance
8-45íSome models. CX-7_8BM8-EA-10I_Edition1 Page437
Friday, September 10 2010 4:24 PM
Form No.8BM8-EA-10I

Black plate (443,1)
qFuse Panel Description
Fuse block (Engine compartment)
DESCRIPTIONFUSE
RATINGPROTECTED COMPONENT
1 PCS――
2 BLOWER 40 A Air conditioner
3 FUEL PUMP 30 A Fuel pump
4 FAN 2 40 A Cooling fan
5 IG KEY 1 40 A For protection of various circuits
6 FAN 1 40 A Cooling fan
7 P.SEAT (D) 30 A Power seat
í
8 INJ 1 30 A Engine control systemí
9 P.SEAT (P) 30 A Power seatí
10 BOSE 30 A Bose®audio systemí
11 ENGINE 30 A Engine control system
12 D.LOCK 20 A Power door locks
13 P.WIND 30 A Power windows
14 IG KEY 2 40 A For protection of various circuits
15 ABS 1 40 A ABS
16 ABS 2 20 A ABS
17 DSC――
Maintenance and Care
Owner Maintenance
8-51íSome models. CX-7_8BM8-EA-10I_Edition1 Page443
Friday, September 10 2010 4:24 PM
Form No.8BM8-EA-10I

Black plate (444,1)
DESCRIPTIONFUSE
RATINGPROTECTED COMPONENT
18 H/L CLEAN/ROOF 20 A Moonroof
í
19 DEF 30 A Rear window defroster
20 TNS 15 A Parking lights, License plate lights, Illumination
21 A/C 10 A Air conditioner
22 TRAILER/TCM 20 A Transaxle control system
í
23 HEAD HI RH 15 A Headlight high beam (RH)
24 HEAD HI LH 15 A Headlight high beam (LH)
25 HEAD LO RH 15 A Headlight low beam (RH)
26 HEAD LO LH 15 A Headlight low beam (LH)
27 ETC 10 A Engine control system
í
28 ENG BAR 2 7.5 A Engine control system
29 ECM 10 A Engine control system
30 INJ 2 10 A Engine control system
í
31 ENG BAR 1 15 A Engine control system
32 FOG 15 A Fog lightsí
33 STOP 10 A Brake lights
34 HORN 20 A Horn
35
25 A Engine control system
36 HAZARD 10 A Hazard warning flashers, Turn signals
8-52
Maintenance and Care
íSome models.
Owner Maintenance
CX-7_8BM8-EA-10I_Edition1 Page444
Friday, September 10 2010 4:24 PM
Form No.8BM8-EA-10I

Black plate (445,1)
Fuse block (Driver's side)
DESCRIPTIONFUSE
RAT-
INGPROTECTED COMPONENT
1 P.WIND 2 30 A Power windows
2 OUTLET 1 15 A Accessory Socket
3 P.MIR 7.5 A Power control mirror
4 OUTLET 2 15 A Accessory Socket
5 SCR――
6 WIPER 20 A Windshield wiper and washer
7 M.DEF 7.5 A Mirror defroster
í
8 P/ST/ENGBAR 3 7.5 A Engine control system
9 P.WIND――
10 A/B 7.5 A Air bag
11 ENGINE 15 A Engine control system
12 METER 15 A Instrument cluster
13 ILLUMI 10 A Dashboard illumination
14 ROOM 15 A Audio system, Overhead light
15 R.FOG――
16 SIREN――
17 SEAT 20 A Seat warmer
í
18 A/C 10 A Air conditioner
Maintenance and Care
Owner Maintenance
8-53íSome models. CX-7_8BM8-EA-10I_Edition1 Page445
Friday, September 10 2010 4:24 PM
Form No.8BM8-EA-10I

Black plate (449,1)
Exterior Care
Followalllabel and container directions
when using a chemical cleaner or polish.
Read all warnings and cautions.
qMaintaining the Finish
Washing
CAUTION
When the wiper lever is in the AUTO
position and the ignition is switched
ON, the wipers may move
automatically in the following cases:
ØIf the windshield above the rain
sensor is touched or wiped with a
cloth.
ØIf the windshield is struck with a
hand or other object from either
outside or inside the vehicle.
Keep hands and scrapers clear of the
windshield when the wiper lever is in
the AUTO position and the ignition is
switched ON as fingers could be
pinched or the wipers and wiper
blades damaged when the wipers
activate automatically.
If you are going to clean the
windshield, be sure the wipers are
turned off completely―this is
particularly important when clearing
ice and snow―when it is most likely
that the engine is left running.
To help protect the finish from rust and
deterioration, wash your Mazda
thoroughly and frequently, at least once a
month, with lukewarm or cold water.
If the vehicle is washed improperly, the
paint surface could be scratched. Here are
some examples of how scratching could
occur.Scratches occur on the paint surface
when:
lThe vehicle is washed without first
rinsing off dirt and other foreign
matter.
lThe vehicle is washed with a rough,
dry, or dirty cloth.
lThe vehicle is washed at a car wash
that uses brushes that are dirty or too
stiff.
lCleansers or wax containing abrasives
are used.
NOTE
lMazda is not responsible for scratches
caused by automatic car washes or
improper washing.
lScratches are more noticeable on vehicles
with darker paint finishes.
To minimize scratches on the vehicle's
paint finish:
lRinse off any dirt or other foreign
matter using lukewarm or cold water
before washing.
lUse plenty of lukewarm or cold water
and a soft cloth when washing the
vehicle. Do not use a nylon cloth.
lRub gently when washing or drying the
vehicle.
lTake your vehicle only to a car wash
that keeps its brushes well maintained.
lDo not use abrasive cleansers or wax
that contain abrasives.
Maintenance and Care
Appearance Care
8-57
CX-7_8BM8-EA-10I_Edition1 Page449
Friday, September 10 2010 4:24 PM
Form No.8BM8-EA-10I

Black plate (453,1)
NOTElDo not use a wire brush or any abrasive
cleaner, polishing compound, or solvent on
aluminum wheels. They may damage the
coating.
lAlways use a sponge or soft cloth to clean
the wheels.
Rinse the wheels thoroughly with lukewarm
or cold water. Also, be sure to clean the
wheels after driving on dusty or salted
roads to help prevent corrosion.
lAvoid washing your vehicle in an automatic
car wash that uses high-speed or hard
brushes.
lIf your aluminum wheels lose luster, wax
the wheels.
(With Tire Pressure Monitoring System)
Check special requirements for Tire Pressure
Monitoring System.
Refer to Tires and Wheels on page 5-33.
qPlastic Part Maintenance
lWhen cleaning the plastic lenses of the
lights, do not use gasoline, kerosene,
rectified spirit, paint, thinner, highly
acidic detergents, or strongly alkaline
detergents. Otherwise, these chemical
agents can discolor or damage the
surfaces resulting in a significant loss
in functionality. If plastic parts become
inadvertently exposed to any of these
chemical agents, flush with water
immediately.
lIf plastic parts such as the bumpers
become inadvertently exposed to
chemical agents or fluids such as
gasoline, oil, engine coolant, or battery
fluid, it could cause discoloration,
staining, or paint peeling. Wipe off any
such chemical agents or fluids using a
soft cloth immediately.
lHigh water temperature and high water
pressure car washers are available
depending on the type of high pressure
car washer device. If the car washer
nozzle is put too close to the vehicle or
aimed at one area for an extended
period of time, it could deform plastic
parts or damage the paint.
lDo not use wax containing compounds
(polish). Otherwise, it could result in
paint damage.
lIn addition, do not use an electrical or
air tool to apply wax. Otherwise, the
frictional heat generated could result in
deformation of plastic parts or paint
damage.
Maintenance and Care
Appearance Care
8-61
CX-7_8BM8-EA-10I_Edition1 Page453
Friday, September 10 2010 4:24 PM
Form No.8BM8-EA-10I