2011 MAZDA MODEL 2 brake light

Black plate (270,1)
High-mount brake light
Due to the complexity and difficulty of
the procedure, the LED bulbs must be
replaced by an Authorized Mazda Dealer.
NOTE
LED bulb replacement is not possible because
it is built into the unit. Replace the unit.
License plate light
1. Wrap a flathead screwdriver with a softcloth to prevent damage to the lens and
remove the lens by carefully prying on
the edge of the lens with the flathead
screwdriver.
2. Disconnect the bulb by pulling it out.
Edge
3. Install the new bulb in the reverse order of removal.
qReplacing Interior Light Bulbs
Overhead light
1. Wrap a small flathead screwdriver with
a soft cloth to prevent damage to the
lens and remove the lens by carefully
prying on the edge of the lens with the
flathead screwdriver.
2. Disconnect the bulb by pulling it out.
Edge
3. Install the new bulb in the reverse order of removal.
8-38
Maintenance and Care
Owner Maintenance
Mazda2_8BX2-EA-10K_Edition2 Page270
Thursday, December 23 2010 4:48 PM
Form No.8BX2-EA-10K

Black plate (274,1)
qFuse Panel Description
Fuse block (Engine compartment)
DESCRIPTION FUSE
RATING PROTECTED COMPONENT
1 ―― ―
2 FUEL PUMP 15 A Fuel pump
3 F.FOG 15 A Fog lights
í
4 P/W 20 A Power windows
5 HORN 10 A Horn
6 EGI 10 A Engine control system
7 DSC-P 30 A DSC
8 DSC-V 20 A DSC
9 MAG 7.5 A Air conditioner
10 TAIL 15 A Taillights, Parking lights, License plate lights
11 STOP 10 A Brake lights
12 SWS 7.5 A Air bag
13 R.DEF 20 A Rear window defroster
14 HAZARD 10 A Hazard warning flashers, Turn signal lights
15 D/L 20 A Power door locks
16 ENG BAR 15 A Air flow sensor, Engine control system
17 ENG INJ 15 A Engine control system
8-42
Maintenance and Care
íSome models.
Owner Maintenance
Mazda2_8BX2-EA-10K_Edition2 Page274
Thursday, December 23 2010 4:49 PM
Form No.8BX2-EA-10K

Black plate (280,1)
CAUTION
ØDo not use steel wool, abrasive
cleaners, or strong detergents
containing highly alkaline or
caustic agents on chrome-plated
or anodized aluminum parts. This
may damage the protective
coating; also, cleaners and
detergents may discolor or
deteriorate the paint.
Ø To prevent damaging the antenna,
remove it before entering a car
wash facility or passing beneath a
low overhead clearance.
Pay special attention to removing salt,
dirt, mud, and other foreign material from
the underside of the fenders, and make
sure the drain holes in the lower edges of
the doors and rocker panels are clean.
Insects, tar, tree sap, bird droppings,
industrial fallout, and similar deposits can
damage the finish if not removed
immediately. When prompt washing with
plain water is ineffective, use a mild soap
made for use on vehicles.
Thoroughly rinse off all soap with
lukewarm or cold water. Do not allow
soap to dry on the finish.
After washing the vehicle, dry it with a
clean chamois to prevent water spots from
forming.
WARNING
Dry off brakes that have become wet
by driving slowly, releasing the
accelerator pedal and lightly applying
the brakes several times until the brake
performance returns to normal: Driving with wet brakes is
dangerous. Increased stopping
distance or the vehicle pulling to one
side when braking could result in a
serious accident. Light braking will
indicate whether the brakes have
been affected.
When using a high water pressure car
wash
High water temperature and high water
pressure car washers are available
depending on the type of car wash
machine. If the car washer nozzle is put
too close to the vehicle, the force of the
spray could damage or deform the
molding, affect the sealability of parts,
and allow water to penetrate the interior.
Keep a sufficient space (30 cm or more)
between the nozzle and the vehicle. In
addition, do not spend too much time
spraying the same area of the vehicle, and
be very careful when spraying between
gaps in doors and around windows.
Waxing
Your vehicle needs to be waxed when
water no longer beads on the finish.
Always wash and dry the vehicle before
waxing it. In addition to the vehicle body,
wax the metal trim to maintain its luster.
1. Use wax which contains no abrasives. Waxes containing abrasive will remove
paint and could damage bright metal
parts.
8-48
Maintenance and Care
Appearance Care
Mazda2_8BX2-EA-10K_Edition2 Page280
Thursday, December 23 2010 4:49 PM
Form No.8BX2-EA-10K

Black plate (281,1)
2. Use a good grade of natural wax formetallic, mica, and solid colors.
3. When waxing, coat evenly with the sponge supplied or a soft cloth.
4. Wipe off the wax with a soft cloth.
NOTE
A spot remover to remove oil, tar, and similar
materials will usually also take off the wax.
Rewax these areas even if the rest of the
vehicle does not need it.
q Repairing Damage to the Finish
Deep scratches or chips on the finish
should be repaired promptly. Exposed
metal quickly rusts and can lead to major
repairs.
CAUTION
If your Mazda is damaged and needs
metal parts repaired or replaced,
make sure the body shop applies
anti-corrosion materials to all parts,
both repaired and new. This will
prevent them from rusting.
qUnderbody Maintenance
Road chemicals and salt used for ice and
snow removal and solvents used for dust
control may collect on the underbody. If
not removed, they will speed up rusting
and deterioration of such underbody parts
as fuel lines, frame, floor pan, and exhaust
system, even though these parts may be
coated with anti-corrosive material.
Thoroughly flush the underbody and
wheel housings with lukewarm or cold
water at the end of each winter. Try also
to do this every month. Pay special attention to these areas
because they easily hide mud and dirt.
It
will do more harm than good to wet
down the road grime without removing
it.
The lower edges of doors, rocker panels,
and frame members have drain holes that
should not be clogged. Water trapped
there will cause rusting.
WARNING
Dry wet brakes by driving very slowly
and applying the brakes lightly until
brake performance is normal: Driving with wet brakes is
dangerous. Increased stopping
distance or the vehicle pulling to one
side when braking could result in a
serious accident. Light braking will
indicate whether the brakes have
been affected.
qAluminum Wheel Maintenanceí
A protective coating is provided over the
aluminum wheels. Special care is needed
to protect this coating.
CAUTION
Do not use any detergent other than
mild detergent. Before using any
detergent, verify the ingredients.
Otherwise, the product could discolor
or stain the aluminum wheels.
Maintenance and Care
Appearance Care
8-49íSome models.
Mazda2_8BX2-EA-10K_Edition2 Page281
Thursday, December 23 2010 4:49 PM
Form No.8BX2-EA-10K

Black plate (331,1)
qDimensions
Item Vehicle specification
Overall length With front license plate mount cover
3,965 mm (156.1 in)
Without front license plate mount
cover 3,955 mm (155.7 in)
Overall width 1,695 mm (66.7 in)
Overall height 1,475 mm (58.1 in)
Front tread 1,476 mm (58.1 in)
Rear tread 1,466 mm (57.7 in)
Wheelbase 2,490 mm (98 in)
qWeights
Item Weight
Manual transaxle Automatic transaxle
GVWR (Gross Vehicle Weight Rating) 1,480 kg (3,263 lbs) 1,502 kg (3,311 lbs)
GAWR
(Gross Axle Weight Rat-
ing) Front 774 kg (1,706 lbs) 799 kg (1,761 lbs)
Rear 706 kg (1,556 lbs) 703 kg (1,550 lbs)
q
Air Conditioner
Item Classification
Refrigerant Type HFC134a (R-134a)
qLight Bulbs
Exterior light
Light bulb Category
Wattage ECE R (SAE)
Headlights 60/55 ―(HB2)
Front turn signal lights 21 PY21W (22.3CP)
Parking lights (Front side-marker lights) 5 W5W (4CP)
Fog lights
í55 H11 (H11)
Side turn signal lights*15 WY5W (―)
High-mount brake light LED*2― (― )
Rear turn signal lights 21 WY21W (23CP)
Brake lights/Taillights (Rear side-marker lights) 21/5 W21/5W (#7443)
Reverse lights 16 W16W (#921)
License plate light 5 W5W ( ―)
*1 Bulb replacement is not possible because it is built into the unit. Replace the unit.
*2 LED is the abbreviation for Light Emitting Diode.
Specifications
10-5íSome models.
Mazda2_8BX2-EA-10K_Edition2 Page331
Thursday, December 23 2010 4:49 PM
Form No.8BX2-EA-10K

Black plate (336,1)
A
Accessory Socket .............................. 6-42
Add-On Non-Genuine Parts and
Accessories ....................................... 9-17
Air Bag Systems ............................... 2-36
Antenna ............................................... 6-9
Anti-Lock Brake System (ABS) ......... 5-8Warning light ............................... 5-8
Appearance Care ............................... 8-45
Audio System ..................................... 6-9 Audio control switch .................. 6-33
Audio set .................................... 6-19
AUX mode ................................. 6-35
Operating tips for audio
system ........................................ 6-10
Safety certification ..................... 6-37
Automatic Transaxle ......................... 5-12 Driving tips ................................ 5-14
Fluid ........................................... 8-16
Overdrive ................................... 5-14
Shift-lock system ....................... 5-13
Transaxle ranges ........................ 5-12
B
BatteryEmergency starting .................... 7-17
Maintenance ............................... 8-23
Specifications ............................. 10-4
Beep Sounds
Lights-on reminder ..................... 5-50
Seat belt warning ........................ 5-50
Tire inflation pressure warning ... 5-50
Beeps Ignition key reminder ................. 5-50
Before Starting the Engine .................. 4-5 After getting in ............................. 4-5
Before getting in .......................... 4-5
Body Lubrication .............................. 8-19
B
Bottle Holder ..................................... 6-40
Brake/Clutch Fluid ........................................... 8-15
Brakes Anti-lock brake system (ABS) ..... 5-8
Brakes assist ................................. 5-9
Foot brake .................................... 5-5
Pad wear indicator ...................... 5-10
Parking brake ............................... 5-6
Warning light ............................... 5-7
Break-In Period ................................... 4-6
Bulb Replacement ............................. 8-32
C
Capacities .......................................... 10-4
Carbon Monoxide ............................... 4-4
Catalytic Converter ............................. 4-3
Cell Phones ....................................... 9-18
Center Console Tray ......................... 6-41
Child Restraint Child restraint precautions ......... 2-21
Child-restraint system installation
position ...................................... 2-25
Installing child-restraint
systems ....................................... 2-26
LATCH child-restraint
systems ....................................... 2-32
Child Safety Locks for Rear Doors ... 3-11
Climate Control System ...................... 6-2 Gas specifications ...................... 10-5
Cruise Control ................................... 5-16
Cup Holder ........................................ 6-39
Customer Assistance ........................... 9-2
D
Dashboard Illumination .................... 5-32
11-2
Index
Mazda2_8BX2-EA-10K_Edition2 Page336
Thursday, December 23 2010 4:49 PM
Form No.8BX2-EA-10K

Black plate (337,1)
D
Daytime Running Lights ................... 5-53
DefrosterMirror ......................................... 5-59
Rear window .............................. 5-59
Dimensions ....................................... 10-5
Door Locks ......................................... 3-8
Driving In Flooded Area ................... 4-10
Driving on Uneven Road .................. 4-11
Driving Tips ........................................ 4-6 Automatic transaxle ................... 5-14
Break-in period ............................ 4-6
Driving in flooded area .............. 4-10
Driving on uneven road .............. 4-11
Hazardous driving ........................ 4-7
Money-saving suggestions ........... 4-6
Rocking the vehicle ...................... 4-8
Winter driving .............................. 4-8
Dynamic Stability Control (DSC) ..... 5-21 DSC OFF indicator light ............ 5-22
DSC OFF switch ........................ 5-22
TCS/DSC indicator light ............ 5-21
E
Emergency Starting ........................... 7-17Flooded engine ........................... 7-17
Jump-starting .............................. 7-18
Push-starting .............................. 7-21
Emergency Towing ........................... 7-22
Emission Control System .................... 4-3
Engine Coolant ....................................... 8-13
Exhaust gas .................................. 4-4
Hood release .............................. 3-20
Oil .............................................. 8-12
Overheating ................................ 7-15
Starting ......................................... 5-3
Engine Compartment Overview ........ 8-11
E
Engine Coolant Overheating ................................ 7-15
Exhaust Gas ........................................ 4-4
Exterior Care ..................................... 8-47
F
Flasher Hazard warning .......................... 5-60
Headlights .................................. 5-51
Flat Tire ............................................... 7-3 Changing ...................................... 7-6
Spare tire and tool storage ............ 7-3
Fluids Classification .............................. 10-4
Owner maintenance ..................... 8-8
Fog Lights ......................................... 5-54
Foot Brake .......................................... 5-5
Front Seats .......................................... 2-2
Fuel
Filler lid and cap ........................ 3-18
Gauge ......................................... 5-31
Requirements ............................... 4-2
Tank capacity ............................. 10-4
Fuses ................................................. 8-39
Panel description ........................ 8-42
Replacement ............................... 8-39
G
Gauges .............................................. 5-29
Glove Compartment .......................... 6-41
H
Hazard Warning Flasher .................... 5-60
Hazardous Driving .............................. 4-7
Head Restraint .................................... 2-7
Index
11-3
Mazda2_8BX2-EA-10K_Edition2 Page337
Thursday, December 23 2010 4:49 PM
Form No.8BX2-EA-10K

Black plate (339,1)
P
Paint Damage .................................... 8-45
Parking Brake ..................................... 5-6
Parking in an Emergency .................... 7-2
Personalization Features ................... 10-7
Power Door Locks .............................. 3-9
Power Steering .................................. 5-15Power steering malfunction indicator
light ............................................ 5-15
Power Windows ................................ 3-15
Push-Starting ..................................... 7-21
R
Rear Door Child Safety Locks .......... 3-11
Rear Seat ............................................. 2-4
Rear Window Defroster .................... 5-59
Rear Window Washer ....................... 5-58
Rear Window Wiper .......................... 5-58
Rearview Mirror ................................ 3-25
Recreational Towing ......................... 7-24
Registering Your Vehicle in A Foreign
Country ............................................. 9-16
Rocking the Vehicle ............................ 4-8
S
Safety Defects, Reporting ................. 9-40
Seat Belt System 3-point type ................................ 2-13
Automatic locking ...................... 2-12
Belt minder ................................. 2-19
Emergency locking .................... 2-11
Extender ..................................... 2-17
Pregnant women ......................... 2-11
Pretensioner and load limiting .... 2-15
Seat belt precautions .................... 2-9
Warning light/beep ..................... 2-19
S
SeatsFront seat ...................................... 2-2
Head restraint ............................... 2-7
Rear seat ....................................... 2-4
Security System Immobilizer system .................... 3-21
Service Publications .......................... 9-42
Spare Tire and Tool Storage ................ 7-3
Specifications .................................... 10-4
Speedometer ...................................... 5-30
SRS Air Bags
Driver and front passenger occupant
classification system .................. 2-50
How the SRS air bags work ....... 2-42
Limitations to SRS air bag ......... 2-48
Monitoring and maintenance ..... 2-55
SRS air bag deployment
criteria ........................................ 2-47
Supplemental restraint system
(SRS) precautions ...................... 2-36
Supplemental restraint system
components ................................ 2-41
Starting the Engine .............................. 5-3
Steering Wheel .................................. 3-24
Horn ........................................... 5-60
Storage Compartments ...................... 6-41 Center Console Tray ................... 6-41
Glove Compartment ................... 6-41
Sunvisors .......................................... 6-38
T
Tachometer ........................................ 5-31
Temporary Spare Tire ....................... 8-29
Tiedown Hook .......................................... 7-23
Tire Information ................................ 9-21
Index
11-5
Mazda2_8BX2-EA-10K_Edition2 Page339
Thursday, December 23 2010 4:49 PM
Form No.8BX2-EA-10K