2011 MAZDA MODEL 2 bulb

Black plate (267,1)
3. Disconnect the electrical connectorfrom the bulb by pressing the tab on
the connector with your finger and
pulling the connector.
4. Turn the bulb assemblycounterclockwise and remove it.
5. Install the new bulb in the reverse order
of removal.
NOTE
lTo replace the bulb, contact an Authorized
Mazda Dealer.
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton of the
replacement bulb to dispose of the old bulb
promptly out of the reach of children.
Front turn signal lights
1. Make sure the ignition is switched off and the headlight switch is off.
2. Lift the hood.
3. Turn the socket and bulb assembly counterclockwise and remove it.
4. Remove the bulb by pushing it in slightly and turning it
counterclockwise.
5. Install the new bulb in the reverse orderof removal.
Parking lights/Front side-marker lights
1. Make sure the headlight switch is off.
2. If you are changing the right bulb, startthe engine, turn the steering wheel all
the way to the left, and turn off the
engine. If you are changing the left
bulb, turn the steering wheel to the
right.
Maintenance and Care
Owner Maintenance
8-35
Mazda2_8BX2-EA-10K_Edition2 Page267
Thursday, December 23 2010 4:48 PM
Form No.8BX2-EA-10K

Black plate (268,1)
3. Turn the screws and the center sectionof the plastic retainers
counterclockwise and remove them,
then partially peel back the mudguard.
Removal
Installation
4. Turn the socket and bulb assembly counterclockwise and remove it.
5. Disconnect the bulb from the socket.
6. Install the new bulb in the reverse order of removal.
Side turn signal lights
1. Make sure the ignition is switched offand the headlight switch is off.
2. Slide the unit as shown in the figure to remove it.
3. Detach the electrical connector fromthe unit by pulling it outward.
4. Install the new side turn signal unit inthe reverse order of removal.
NOTE
Bulb replacement is not possible because it is
built into the unit. Replace the unit.
8-36
Maintenance and Care
Owner Maintenance
Mazda2_8BX2-EA-10K_Edition2 Page268
Thursday, December 23 2010 4:48 PM
Form No.8BX2-EA-10K

Black plate (269,1)
Brake lights/Taillights (Rear side
marker lights)/Rear turn signal lights/
Reverse lights
1. Make sure the ignition is switched offand the headlight switch is off.
2. Turn the bolts counterclockwise and remove them.
3. Pull the unit rearward to remove it.
4. Turn the socket and bulb assemblycounterclockwise and remove it.
5. Disconnect the bulb from the socket. Brake lights/Taillights (Rear side
marker lights)
Rear turn signal lights
Reverse lights
6. Install the new bulb in the reverse order
of removal.
Maintenance and Care
Owner Maintenance
8-37
Mazda2_8BX2-EA-10K_Edition2 Page269
Thursday, December 23 2010 4:48 PM
Form No.8BX2-EA-10K

Black plate (270,1)
High-mount brake light
Due to the complexity and difficulty of
the procedure, the LED bulbs must be
replaced by an Authorized Mazda Dealer.
NOTE
LED bulb replacement is not possible because
it is built into the unit. Replace the unit.
License plate light
1. Wrap a flathead screwdriver with a softcloth to prevent damage to the lens and
remove the lens by carefully prying on
the edge of the lens with the flathead
screwdriver.
2. Disconnect the bulb by pulling it out.
Edge
3. Install the new bulb in the reverse order of removal.
qReplacing Interior Light Bulbs
Overhead light
1. Wrap a small flathead screwdriver with
a soft cloth to prevent damage to the
lens and remove the lens by carefully
prying on the edge of the lens with the
flathead screwdriver.
2. Disconnect the bulb by pulling it out.
Edge
3. Install the new bulb in the reverse order of removal.
8-38
Maintenance and Care
Owner Maintenance
Mazda2_8BX2-EA-10K_Edition2 Page270
Thursday, December 23 2010 4:48 PM
Form No.8BX2-EA-10K

Black plate (271,1)
Luggage compartment light
1. Wrap a small flathead screwdriver witha soft cloth to prevent damage to the
lens and remove the lens by carefully
prying on the edge of the lens with the
flathead screwdriver.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order of removal.
Fuses
Your vehicle's electrical system is
protected by fuses.
If any lights, accessories, or controls don't
work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.
qFuse Replacement
Replacing the fuses on the vehicle's left
side
If the electrical system does not work,
first inspect the fuses on the vehicle's left
side.
1. Make sure the ignition is switched off,
and other switches are off.
2. Remove the cover.
Maintenance and Care
Owner Maintenance
8-39
Mazda2_8BX2-EA-10K_Edition2 Page271
Thursday, December 23 2010 4:48 PM
Form No.8BX2-EA-10K

Black plate (331,1)
qDimensions
Item Vehicle specification
Overall length With front license plate mount cover
3,965 mm (156.1 in)
Without front license plate mount
cover 3,955 mm (155.7 in)
Overall width 1,695 mm (66.7 in)
Overall height 1,475 mm (58.1 in)
Front tread 1,476 mm (58.1 in)
Rear tread 1,466 mm (57.7 in)
Wheelbase 2,490 mm (98 in)
qWeights
Item Weight
Manual transaxle Automatic transaxle
GVWR (Gross Vehicle Weight Rating) 1,480 kg (3,263 lbs) 1,502 kg (3,311 lbs)
GAWR
(Gross Axle Weight Rat-
ing) Front 774 kg (1,706 lbs) 799 kg (1,761 lbs)
Rear 706 kg (1,556 lbs) 703 kg (1,550 lbs)
q
Air Conditioner
Item Classification
Refrigerant Type HFC134a (R-134a)
qLight Bulbs
Exterior light
Light bulb Category
Wattage ECE R (SAE)
Headlights 60/55 ―(HB2)
Front turn signal lights 21 PY21W (22.3CP)
Parking lights (Front side-marker lights) 5 W5W (4CP)
Fog lights
í55 H11 (H11)
Side turn signal lights*15 WY5W (―)
High-mount brake light LED*2― (― )
Rear turn signal lights 21 WY21W (23CP)
Brake lights/Taillights (Rear side-marker lights) 21/5 W21/5W (#7443)
Reverse lights 16 W16W (#921)
License plate light 5 W5W ( ―)
*1 Bulb replacement is not possible because it is built into the unit. Replace the unit.
*2 LED is the abbreviation for Light Emitting Diode.
Specifications
10-5íSome models.
Mazda2_8BX2-EA-10K_Edition2 Page331
Thursday, December 23 2010 4:49 PM
Form No.8BX2-EA-10K

Black plate (332,1)
Interior lightLight bulb Category
Wattage ECE R
Luggage compartment light 5 ―
Overhead light 10 ―
qTires
NOTE
The tires have been optimally matched with the chassis of your vehicle.
When replacing tires, Mazda recommends that you replace tires of the same type originally fitted to
your vehicle. For details, contact an Authorized Mazda Dealer.
Check the tire pressure label for tire size and inflation pressure. Refer to Tire Inflation
Pressure on page 8-26.
Standard tire
Tire size Inflation pressure
Front Rear
185/55R15 82V 220 kPa (32 psi) 210 kPa (30 psi)
Temporary spare tire
Tire size Inflation pressure
T115/70D14 88M 420 kPa (60 psi)
qFuses
Refer to Fuses on page 8-39.
10-6
Specifications
Mazda2_8BX2-EA-10K_Edition2 Page332
Thursday, December 23 2010 4:49 PM
Form No.8BX2-EA-10K

Black plate (336,1)
A
Accessory Socket .............................. 6-42
Add-On Non-Genuine Parts and
Accessories ....................................... 9-17
Air Bag Systems ............................... 2-36
Antenna ............................................... 6-9
Anti-Lock Brake System (ABS) ......... 5-8Warning light ............................... 5-8
Appearance Care ............................... 8-45
Audio System ..................................... 6-9 Audio control switch .................. 6-33
Audio set .................................... 6-19
AUX mode ................................. 6-35
Operating tips for audio
system ........................................ 6-10
Safety certification ..................... 6-37
Automatic Transaxle ......................... 5-12 Driving tips ................................ 5-14
Fluid ........................................... 8-16
Overdrive ................................... 5-14
Shift-lock system ....................... 5-13
Transaxle ranges ........................ 5-12
B
BatteryEmergency starting .................... 7-17
Maintenance ............................... 8-23
Specifications ............................. 10-4
Beep Sounds
Lights-on reminder ..................... 5-50
Seat belt warning ........................ 5-50
Tire inflation pressure warning ... 5-50
Beeps Ignition key reminder ................. 5-50
Before Starting the Engine .................. 4-5 After getting in ............................. 4-5
Before getting in .......................... 4-5
Body Lubrication .............................. 8-19
B
Bottle Holder ..................................... 6-40
Brake/Clutch Fluid ........................................... 8-15
Brakes Anti-lock brake system (ABS) ..... 5-8
Brakes assist ................................. 5-9
Foot brake .................................... 5-5
Pad wear indicator ...................... 5-10
Parking brake ............................... 5-6
Warning light ............................... 5-7
Break-In Period ................................... 4-6
Bulb Replacement ............................. 8-32
C
Capacities .......................................... 10-4
Carbon Monoxide ............................... 4-4
Catalytic Converter ............................. 4-3
Cell Phones ....................................... 9-18
Center Console Tray ......................... 6-41
Child Restraint Child restraint precautions ......... 2-21
Child-restraint system installation
position ...................................... 2-25
Installing child-restraint
systems ....................................... 2-26
LATCH child-restraint
systems ....................................... 2-32
Child Safety Locks for Rear Doors ... 3-11
Climate Control System ...................... 6-2 Gas specifications ...................... 10-5
Cruise Control ................................... 5-16
Cup Holder ........................................ 6-39
Customer Assistance ........................... 9-2
D
Dashboard Illumination .................... 5-32
11-2
Index
Mazda2_8BX2-EA-10K_Edition2 Page336
Thursday, December 23 2010 4:49 PM
Form No.8BX2-EA-10K