2011 LEXUS RX350 reset

166
2-2. Instrument cluster
Gauges and meters
Tachometer
Displays the engine speed in revolutions per minute
Multi-information display
→P. 1 7 3
Speedometer
Displays the vehicle speed
Fuel gauge
Displays the quantity of fuel remaining in the tank
Odometer and trip meter
Odometer: Displays the total distance the vehicle has been driven
Trip meter: Displays the distance the vehicle has been driven since the
meter was last reset. Trip meters “A” and “B” can be used to
record and display different distances independently.
Automatic transmission shift position indicator
→P. 1 5 9
Engine coolant temperature gauge
Displays the engine coolant temperature

167
2-2. Instrument cluster
2

When driving
Changing the display
Switches between odometer and
trip meter displays. When the trip
meter is displayed, pressing and
holding the button will reset the
trip meter.
Instrument panel light control buttons
The brightness of the instrument panel lights can be adjusted.
Darker
Brighter
nThe meters and display illuminate when
The “ENGINE START STOP” switch is in IGNITION ON mode.
NOTICE
nTo prevent damage to the engine and its components
lDo not let the indicator needle of the tachometer enter the red zone, which indi-
cates the maximum engine speed.
lThe engine may be overheating if the engine coolant temperature gauge is in the
red zone (H). In this case, immediately stop the vehicle in a safe place, and check
the engine after it has cooled completely. (→P. 5 8 7 )

176
2-2. Instrument cluster
Trip information
nCurrent fuel consumption
Displays the current rate of fuel consumption
nAverage fuel consumption after refueling
Displays the average fuel consumption since the vehicle was last refueled
nAverage fuel consumption
Displays the average fuel consumption since the function was reset
The function can be reset by pushing the “ENTER” switch for longer than
one second when the average fuel consumption is displayed.
nAverage vehicle speed
Displays the average vehicle speed since the function was reset
The function can be reset by pushing the “ENTER” switch for longer than
one second when the average vehicle speed is displayed.
nCruising range
Displays the estimated maximum distance that can be driven with the
quantity of fuel remaining

206
2-4. Using other driving systems
nCruise control can be set when
lThe shift lever is in D or “4”, “5” or “6” range of S has been selected.
lVehicle speed is above 25 mph (40 km/h).
nAccelerating
The vehicle can be accelerated normally. After acceleration, the set speed
resumes.
nAutomatic cruise control cancelation
The cruise control will stop maintaining the vehicle speed in any of the following sit-
uations:
lActual vehicle speed falls more than 10 mph (16 km/h) below the preset vehicle
speed.
At this time, the memorized set speed is not retained.
lActual vehicle speed is below 25 mph (40km/h).
lVSC is activated.
nIf the cruise control indicator light flashes
Press the “ON-OFF” button once to deactivate the system, and then press the but-
ton again to reactivate the system.
If the cruise control speed cannot be set or if the cruise control cancels immediately
after being activated, there may be a malfunction in the cruise control system. Have
the vehicle inspected by your Lexus dealer.

209
2-4. Using other driving systems
2

When driving
Selecting conventional con-
stant speed control mode:
Press the “ON-OFF” button
to activate the cruise control.
Press the button again to deacti-
vate the cruise control.
Switch to constant speed
control mode.
(Push and hold for approxi-
mately one second.)
Constant speed control mode
indicator will come on.
Vehicle-to-vehicle distance con-
trol mode is always reset when
the “ENGINE START STOP”
switch is turned to IGNITION
ON mode.
nDriving in the selected cruise control mode
Accelerate or decelerate to the
desired speed, and push the
lever down to set the speed.
“SET” will be displayed.

263
2-5. Driving information
2

When driving
Connecting trailer lights
Without towing package: Please consult your dealer when installing
trailer lights, as incorrect installation may cause damage to the vehicle's
lights. Please take care to comply with your state's laws when installing
trailer lights.
With towing package: Use the 4 pin connector located under the rear
bumper.
nAuto current cut-off function (vehicles with towing package)
In case of over current, the auto cut-off function stops the power flowing to the
trailer lights to prevent damage to the vehicle's electrical system.
This function is activated when the rated current of any of the following trailer light
circuit components is exceeded:
lTail lights: maximum 7.8 A
lStop/turn signal light (right): maximum 4.5 A
lStop/turn signal light (left): maximum 4.5 A
nWhen the auto current cut function is activated
If a trailer light does not come on due to the activation of the auto current cut func-
tion, the light system will need to be reset.
Follow the reset procedure shown below.
lIf a tail light does not come on, turn off the headlight switch.
lIf the right-side stop/turn signal light does not come on, put the turn signal in the
off position or remove foot from the brake pedal.
lIf the left-side stop/turn signal light does not come on, put the turn signal in the
off position or remove foot from the brake pedal.
If the emergency flashers do not operate, press the emergency flasher switch to
turn them off.
After the light system is reset, operate the light switches again to see if the lights
operate normally.
If the lights do not operate normally, have the vehicle inspected by your Lexus
dealer.

287
3-2. Using the audio system
3

Interior features
Using the radio
Type A
Traffic information button
Preset station buttons
Radio text message button
Scan button
Seek button
Channel category button
Frequency adjustment
(AM/FM mode) and
channel (SAT mode)
knobAM

⋅
FM/SAT
mode buttons
“PWR ⋅ VOL” k nob
Po w e r Vo l u m e

288
3-2. Using the audio system
Type B
Traffic information button
Preset station buttons
Radio text message button
Scan button
Seek button
Channel category button
Frequency adjustment
(AM/FM mode) and
channel (SAT mode)
knobAM
⋅
FM/SAT
mode buttons
“PWR ⋅ VOL” k nob
Po w e r Vo l u m e