2011 LEXUS RX350 coolant level

SCHEDULED MAINTENANCE LOG

MAINTENANCE
Scheduled Maintenance Log53
54 Months or 45,000 Miles
Clean air conditioner filter
Inspect and adjust all fluid levels
Replace Smart Key battery
Reset maintenance reminder light
Re-torque nuts and bolts of drive shaft (AWD)
Rotate tires
Visually inspect brake pads, calipers and rotors
Check installation of driver’s floor mat
Road-test vehicle
Inspect the following:
___ Axle shaft boots
___Ball joints and dust covers
___Body
___Brake lines and hoses
___Engine coolant (see page 70)
___Exhaust pipes and mountings
Note: If 0W-20 oil was not used at last oil change, or if you drive primarily under certain special operating
conditions, you should also replace the engine oil with 0W-20 oil and replace the oil filter. See page 44 for
conditions that apply. Some conditions require additional maintenance. See below.
If you drive primarily under either of these special operating conditions, perform these
additional items:
Driving off-road, on dirt roads or on dusty roads:
Inspect engine air filter
Tighten nuts and bolts on chassis
To wing a trailer, using a car-top carrier or heavy vehicle loading:
R eplace rear differential oil (AWD)
Replace transfer case oil (AWD)
Tighten nuts and bolts on chassis ___R ack and pinion assembly
___Rear differential oil (AWD)
___Steering linkage and boots
___Transfer case oil (AWD)
Date: ___________________________ Mileage: __________________________
฀8฀9฀5฀7฀7฀_฀2฀0฀1฀1฀฀฀R฀X฀฀฀3฀5฀0฀_฀4฀8฀-฀8฀0฀j฀_฀R฀1฀.฀q฀x฀d฀฀฀฀฀8฀/฀6฀/฀1฀0฀฀฀฀฀7฀:฀5฀2฀฀฀P฀M฀฀฀฀฀P฀a฀g฀e฀฀฀5฀3

SCHEDULED MAINTENANCE LOG

MAINTENANCE
Scheduled Maintenance Log57
90 Months or 75,000 Miles
Clean air conditioner filter
Inspect and adjust all fluid levels
Re-torque nuts and bolts of drive shaft (AWD)
Replace Smart Key battery
Reset maintenance reminder light
Rotate tires
Visually inspect brake pads, calipers and rotors
Check installation of driver’s floor mat
Road-test vehicle
Inspect the following:
___ Axle shaft boots
___Ball joints and dust covers
___Body
___Brake lines and hoses
___Drive belt
___Engine coolant (see page 70)
Note: If 0W-20 oil was not used at last oil change, or if you drive primarily under certain special operating
conditions, you should also replace the engine oil with 0W-20 oil and replace the oil filter. See page 44 for
conditions that apply. Some conditions require additional maintenance. See below.
If you drive primarily under either of these special operating conditions, perform these
additional items:
Driving off-road, on dirt roads or on dusty roads:
Inspect engine air filter
Tighten nuts and bolts on chassis
To wing a trailer, using a car-top carrier or heavy vehicle loading:
R eplace rear differential oil (AWD)
Replace transfer case oil (AWD)
Tighten nuts and bolts on chassis ___ Exhaust pipes and mountings
___Rack and pinion assembly
___Rear differential oil (AWD)
___Steering linkage and boots
___Transfer case oil (AWD)
Date: ___________________________ Mileage: __________________________
฀8฀9฀5฀7฀7฀_฀2฀0฀1฀1฀฀฀R฀X฀฀฀3฀5฀0฀_฀4฀8฀-฀8฀0฀j฀_฀R฀1฀.฀q฀x฀d฀฀฀฀฀8฀/฀6฀/฀1฀0฀฀฀฀฀7฀:฀5฀2฀฀฀P฀M฀฀฀฀฀P฀a฀g฀e฀฀฀5฀7

SCHEDULED MAINTENANCE LOG
MAINTENANCE
Scheduled Maintenance Log60
114 Months or 95,000 Miles 120 Months or 100,000 Miles
R eplace engine oil with 0W-20 oil; r eplace
oil filter
Replace engine coolant (see page 70)
Reset maintenance reminder light
Rotate tires
Visually inspect brake pads, calipers and rotors
Check installation of driver’s floor mat
Road-test vehicle
If you drive primarily under either
of these special operating conditions,
perform these additional items:
Driving off-road, on dirt roads or on
dusty roads:
Inspect axle shaft boots
Inspect ball joints and dust covers
Inspect engine air filter
Inspect steering linkage and boots
Re-torque nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis
To wing a trailer, using a car-top carrier
or heavy vehicle loading:
Re-tor que nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis
Date: ________ Mileage: ________Date: ________ Mileage: ________
Inspect and adjust all fluid levels
Reset maintenance reminder light
Rotate tires
Visually inspect brake pads, calipers and rotors
Check installation of driver’s floor mat
Road-test vehicle
Note: If 0W-20 oil was not used at last oil
change, or if you drive primarily under cer tain
special operating conditions, you should also
replace the engine oil with 0W-20 oil and
replace the oil filter. See page 44 for conditions
that apply. Some conditions require additional
maintenance. See below.
If you drive primarily under either
of these special operating conditions,
perform these additional items:
Driving off-road, on dirt roads or on
dusty roads:
Inspect axle shaft boots
Inspect ball joints and dust covers
Inspect engine air filter
Inspect steering linkage and boots
Re-torque nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis
To wing a trailer, using a car-top carrier
or heavy vehicle loading:
Re-tor que nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis
฀8฀9฀5฀7฀7฀_฀2฀0฀1฀1฀฀฀R฀X฀฀฀3฀5฀0฀_฀4฀8฀-฀8฀0฀j฀_฀R฀1฀.฀q฀x฀d฀฀฀฀฀8฀/฀6฀/฀1฀0฀฀฀฀฀7฀:฀5฀2฀฀฀P฀M฀฀฀฀฀P฀a฀g฀e฀฀฀6฀0

SCHEDULED MAINTENANCE LOG
MAINTENANCE
Scheduled Maintenance Log62
132 Months or 110,000 Miles
R eplace engine oil with 0W-20 oil; r eplace
oil filter
Reset maintenance reminder light
Rotate tires
Visually inspect brake pads, calipers and rotors
Check installation of driver’s floor mat
Road-test vehicle
If you drive primarily under either
of these special operating conditions,
perform these additional items:
Driving off-road, on dirt roads or on
dusty roads:
Inspect axle shaft boots
Inspect ball joints and dust covers
Inspect engine air filter
Inspect steering linkage and boots
Re-torque nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis
To wing a trailer, using a car-top carrier
or heavy vehicle loading:
Re-tor que nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis 138 Months or 115,000 Miles
Date: ________ Mileage: ________Date: ________ Mileage: ________

Inspect and adjust all fluid levels
Inspect engine coolant (see page 70)
Reset maintenance reminder light
Rotate tires
Visually inspect brake pads, calipers and rotors
Check installation of driver’s floor mat
Road-test vehicle
Note: If 0W-20 oil was not used at last oil
change, or if you drive primarily under cer tain
special operating conditions, you should also
replace the engine oil with 0W-20 oil and
replace the oil filter. See page 44 for conditions
that apply. Some conditions require additional
maintenance. See below.
If you drive primarily under either
of these special operating conditions,
perform these additional items:
Driving off-road, on dirt roads or on
dusty roads:
Inspect axle shaft boots
Inspect ball joints and dust covers
Inspect engine air filter
Inspect steering linkage and boots
Re-torque nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis
To wing a trailer, using a car-top carrier
or heavy vehicle loading:
Re-tor que nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis
฀8฀9฀5฀7฀7฀_฀2฀0฀1฀1฀฀฀R฀X฀฀฀3฀5฀0฀_฀4฀8฀-฀8฀0฀j฀_฀R฀1฀.฀q฀x฀d฀฀฀฀฀8฀/฀6฀/฀1฀0฀฀฀฀฀7฀:฀5฀2฀฀฀P฀M฀฀฀฀฀P฀a฀g฀e฀฀฀6฀2

SCHEDULED MAINTENANCE LOG
MAINTENANCE
Scheduled Maintenance Log6 4
150 Months or 125,000 Miles 156 Months or 130,000 Miles
R eplace engine oil with 0W-20 oil; r eplace
oil filter
Inspect engine coolant (see page 70)
Reset maintenance reminder light
Rotate tires
Visually inspect brake pads, calipers and rotors
Check installation of driver’s floor mat
Road-test vehicle
If you drive primarily under either
of these special operating conditions,
perform these additional items:
Driving off-road, on dirt roads or on
dusty roads:
Inspect axle shaft boots
Inspect ball joints and dust covers
Inspect engine air filter
Inspect steering linkage and boots
Re-torque nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis
To wing a trailer, using a car-top carrier
or heavy vehicle loading:
Re-tor que nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis
Date: ________ Mileage: ________Date: ________ Mileage: ________
Inspect and adjust all fluid levels
Reset maintenance reminder light
Rotate tires
Visually inspect brake pads, calipers and rotors
Check installation of driver’s floor mat
Road-test vehicle
Note: If 0W-20 oil was not used at last oil
change, or if you drive primarily under cer tain
special operating conditions, you should also
replace the engine oil with 0W-20 oil and
replace the oil filter. See page 44 for conditions
that apply. Some conditions require additional
maintenance. See below.
If you drive primarily under either
of these special operating conditions,
perform these additional items:
Driving off-road, on dirt roads or on
dusty roads:
Inspect axle shaft boots
Inspect ball joints and dust covers
Inspect engine air filter
Inspect steering linkage and boots
Re-torque nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis
To wing a trailer, using a car-top carrier
or heavy vehicle loading:
Re-tor que nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis
฀8฀9฀5฀7฀7฀_฀2฀0฀1฀1฀฀฀R฀X฀฀฀3฀5฀0฀_฀4฀8฀-฀8฀0฀j฀_฀R฀1฀.฀q฀x฀d฀฀฀฀฀8฀/฀6฀/฀1฀0฀฀฀฀฀7฀:฀5฀2฀฀฀P฀M฀฀฀฀฀P฀a฀g฀e฀฀฀6฀4

SCHEDULED MAINTENANCE LOG
MAINTENANCE
Scheduled Maintenance Log66
168 Months or 140,000 Miles
R eplace engine oil with 0W-20 oil; r eplace
oil filter
Reset maintenance reminder light
Rotate tires
Visually inspect brake pads, calipers and rotors
Check installation of driver’s floor mat
Road-test vehicle
If you drive primarily under either
of these special operating conditions,
perform these additional items:
Driving off-road, on dirt roads or on
dusty roads:
Inspect axle shaft boots
Inspect ball joints and dust covers
Inspect engine air filter
Inspect steering linkage and boots
Re-torque nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis
To wing a trailer, using a car-top carrier
or heavy vehicle loading:
Re-tor que nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis 17 4 Months or 145,000 Miles
Date: ________ Mileage: ________Date: ________ Mileage: ________

Inspect and adjust all fluid levels
Inspect engine coolant (see page 70)
Reset maintenance reminder light
Rotate tires
Visually inspect brake pads, calipers and rotors
Check installation of driver’s floor mat
Road-test vehicle
Note: If 0W-20 oil was not used at last oil
change, or if you drive primarily under cer tain
special operating conditions, you should also
replace the engine oil with 0W-20 oil and
replace the oil filter. See page 44 for conditions
that apply. Some conditions require additional
maintenance. See below.
If you drive primarily under either
of these special operating conditions,
perform these additional items:
Driving off-road, on dirt roads or on
dusty roads:
Inspect axle shaft boots
Inspect ball joints and dust covers
Inspect engine air filter
Inspect steering linkage and boots
Re-torque nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis
To wing a trailer, using a car-top carrier
or heavy vehicle loading:
Re-tor que nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis
฀8฀9฀5฀7฀7฀_฀2฀0฀1฀1฀฀฀R฀X฀฀฀3฀5฀0฀_฀4฀8฀-฀8฀0฀j฀_฀R฀1฀.฀q฀x฀d฀฀฀฀฀8฀/฀6฀/฀1฀0฀฀฀฀฀7฀:฀5฀2฀฀฀P฀M฀฀฀฀฀P฀a฀g฀e฀฀฀6฀6

EXPLANATION OF MAINTENANCE ITEMS
MAINTENANCE
Scheduled Maintenance Log70
Engine Coolant
When inspecting, visually check
the level of the engine coolant on the
see-through reservoir. Add coolant
as necessary. When replacing, drain
and flush the cooling system and refill
with coolant. Always use Genuine
Toyota Super Long-Life Coolant or
similar high-quality non-silicate,
nonamine, non-nitrate, non-borate
ethylene-glycol coolant with long-life
hybrid organic acid technology (i.e.,
a combination of low phosphates and
organic acids). A qualified technician
should perform these operations.
Check the radiator and condenser
for blockage by leaves, dirt or insects
and clean if necessary. Also check
the hose connections for corrosion
and condition of installation.
Note:Initial replacement of engine
coolant is at 120 months/100,000
miles. Replace every 60 months/
50,000 miles thereafter.
Engine Oil and Oil Filter
Replace the oil filter and drain and
refill the engine oil at specified inter-
vals. SAE 0W-20 oil is the best
choice for good fuel economy and
good starting in cold weather. If SAE
0W-20 is not available, SAE 5W-20
may be used; however, it must be
replaced with SAE 0W-20 at the next
oil change. See your Lexus dealer for
oil specifically formulated for your
vehicle’s engine. For instructions on
how to reset the reminder light, refer
to your Owner’s Manual.
Note:If you do the majority of your
driving under any of the special oper-
ating conditions indicated on page
44, you should replace the engine oil
and oil filter every six months or
5,000 miles, regardless of the oil
used or the certification of the vehicle.
Exhaust Pipes and Mountings
Visually inspect the exhaust pipes,
muffler and hangers for cracks,
deterioration and damage. Start
the engine and listen carefully for
any exhaust leakage. Tighten connec-
tions and replace parts as necessary.
฀8฀9฀5฀7฀7฀_฀2฀0฀1฀1฀฀฀R฀X฀฀฀3฀5฀0฀_฀4฀8฀-฀8฀0฀j฀_฀R฀1฀.฀q฀x฀d฀฀฀฀฀8฀/฀6฀/฀1฀0฀฀฀฀฀7฀:฀5฀2฀฀฀P฀M฀฀฀฀฀P฀a฀g฀e฀฀฀7฀0