2011 Lexus IS220d engine

166
2-1. Driving procedures
IS250/220d/200d_EE
When the “-” shift paddle switch is operated in the D position
When the “-” shift paddle switch is operated in the D position, a shift range
will be automatically selected. The highest gear of the first shift range will
be one gear lower than the gear in use during normal D position driving.
Automatic deactivation of shift range selection in the D position
Shift range selection in the D position will be deactivated in the following
situations:
When the vehicle comes to a stop
When range 6 is selected and the accelerator pedal is depressed
If the accelerator pedal is depressed for more than a certain period of
time
To protect automatic transmission
A function is adopted that automatically selects a higher shift range when
the fluid temperature is high.
Gear range display when driving
The current gear is displayed on the multi-information display. (P. 184)
Downshifting restrictions warning buzzer
To help ensure safety and driving performance, downshifting operation may
sometimes be restricted. In some circumstances, downshifting may not be
possible even when the shift lever or shift paddle switch is operated. (The
warning buzzer will sound twice.)
When driving with the cruise control system or dynamic radar cruise control
system
Engine braking will not occur during shift range selection in the D position
or S mode, even when downshifting to range 5 or 4. (P. 198, 202)
Snow mode automatic deactivation
Snow mode is automatically deactivated if the “ENGINE START STOP”
switch is turned off after driving in snow mode.
If the shift lever cannot be shifted from P
P. 5 1 4

169
2-1. Driving procedures
2
When driving
IS250/220d/200d_EE
Maximum downshifting speed
Adhere to the downshifting speeds in the following table in order to prevent
over-revving the engine.
km/h (mph)
Shift positionMaximum speed
146 (28)
291 (56)
3151 (93)
4198 (122)

170
2-1. Driving procedures
IS250/220d/200d_EE
Turn signal lever
Turn signals can be operated when
The “ENGINE START STOP” switch is in IGNITION ON mode.
If the indicators flash faster than usual
Check that a light bulb in the front or rear turn signal lights has not burned
out.
Right turn
Left turn
Move and hold the lever
partway to signal a lane
change
The right hand signal will
flash until you release the
lever.
Move and hold the lever
partway to signal a lane
change
The left hand signal will flash
until you release the lever.

171
2
When driving
IS250/220d/200d_EE
2-2. Instrument cluster
Gauges and meters
The units used on the speedometer, tachometer and fuel gauge display
may differ depending on the model/type.
The following gauges, meters and display illuminate when the
“ENGINE START STOP” switch is in IGNITION ON mode.
Speedometer
Displays the vehicle speed.
Multi-information display
P. 181
Tachometer
Displays the engine speed in revolutions per minute.
Tacho indicator
When the set engine speed is reached, this ring-shaped indicator
comes on in yellow. The indicator comes on in red when the engine
speed reaches a dangerous range.
Engine coolant temperature gauge
Displays the engine coolant temperature.

174
2-2. Instrument cluster
IS250/220d/200d_EEChanging the indicator setting
The satellite switch can be used to change the set speed at which
the yellow speed or tacho indicator ring comes on.
The setting can be made only when the “ENGINE START
STOP” switch is in IGNITION ON mode and the vehicle is
stopped.
Push “
” or “” to select the speed or tacho indicator set mode.
( ) Turn the speed or tacho indicator to “OFF” and then “ON” by
pushing the “ON/OFF” button. ( )
After one second, the mode
enters the indicator setting
mode.
The speedometer or tachometer
needle moves to the previously
set speed.
STEP1

176
2-2. Instrument cluster
IS250/220d/200d_EE
Speed indicator display conditions and vehicle speed setting range
Vehicle speed setting range:
Right-hand drive vehicles:
Approximately 50 to 160 km/h
(Approximately 30 to 100 mph)
Left-hand drive vehicles:
Approximately 50 to 200 km/h
(Approximately 30 to 125 mph)
When the maximum speed is selected, the speed indicator comes on in red.
Tacho indicator display conditions and engine speed setting range
Engine rpm setting range:
IS250: Approximately 2000 to 6500 rpm (r/min)
IS220d and IS200d: Approximately 2000 to 5100 rpm (r/min)
When the maximum rpm is selected, the tacho indicator comes on in red.
NOTICE
To prevent damage to the engine and its components
Do not let the indicator needle of the tachometer enter the red zone, which
indicates the maximum engine speed.
The engine may be overheating if the temperature gauge is in the red zone
(H). In this case, immediately stop the vehicle in a safe place, and check
the engine after it has cooled completely. (
P. 525)

179
2-2. Instrument cluster
2
When driving
IS250/220d/200d_EE
*1:These lights turn on when the “ENGINE START STOP” switch is
turned to IGNITION ON mode to indicate that a system check is
being performed. They will turn off after the engine is started, or
after a few seconds. There may be a malfunction in a system if a
light does not come on, or if the lights do not turn off. Have the
vehicle inspected by any authorized Lexus dealer or repairer, or
another duly qualified and equipped professional, for details.
*2:The light flashes to indicate that the system is operating
(if
equipped)
Daytime running light
system off indicator
(P. 188)SRS airbag on-off indi-
cator (P. 140)
(vehicles
with a man-
ual trans-
mission)Engine preheating indi-
cator (P. 156)
*1

180
2-2. Instrument cluster
IS250/220d/200d_EE
CAUTION
If a safety system warning light does not come on
Should a safety system light such as the ABS and SRS warning light not
come on when you start the engine, this could mean that these systems are
not available to help protect you in an accident, which could result in death
or serious injury. Have the vehicle inspected by any authorized Lexus dealer
or repairer, or another duly qualified and equipped professional, immedi-
ately if this occurs.
Warning lights
Warning lights inform the driver of malfunctions in any of the
vehicle’s systems. (P. 467)
*:These lights turn on when the “ENGINE START STOP” switch is
turned to IGNITION ON mode to indicate that a system check is
being performed. They will turn off after the engine is started, or
after a few seconds. There may be a malfunction in a system if a
light does not come on, or if the lights do not turn off. Have the
vehicle inspected by any authorized Lexus dealer or repairer, or
(vehicles
with a
manual
transmis-
sion)
(if equipped)(for
driver)(for front
passen-
ger)
*****
*****