2011 Lexus IS220d stop start

60
1-2. Opening, closing and locking the doors and trunk
IS250/220d/200d_EE
Automatic door locking and unlocking systems
The following functions can be set or cancelled:
*: Vehicles with an automatic transmission only
FunctionOperation
Shift position linked
door locking function*Shifting the shift lever out of P locks all
doors.
Shift position linked
door unlocking func-
tion*Shifting the shift lever to P unlocks all
doors.
Speed linked door lock-
ing functionAll doors are locked when the vehicle
speed is approximately 20 km/h (12 mph)
or higher.
Driver's door linked
door unlocking function
All doors are unlocked when the driver's
door is opened within approximately 45
seconds after turning the “ENGINE
START STOP” switch OFF.

61
1-2. Opening, closing and locking the doors and trunk
1
Before driving
IS250/220d/200d_EESetting and canceling the function
To switch between setting and canceling, follow the procedure
below:
Close all the doors and switch the “ENGINE START
STOP” switch to IGNITION ON mode. (Perform the step 2
within 10 seconds.)
Shift the shift lever to P or N,
press and hold the driver’s door
lock switch (
or ) for
about 5 seconds then release.
The shift lever and switch posi-
tions corresponding to the
desired function to be set are
shown as follows.
Use the same procedure to can-
cel the function.
*: Vehicles with an automatic transmission only
When the setting or canceling operation is complete, all doors are
locked and then unlocked.
STEP1
STEP2
FunctionShift lever posi-
tionDriver’s door
lock switch posi-
tion
Shift position linked door lock-
ing function*
PShift position linked door
unlocking function*
Speed linked door locking func-
tion
NDriver's door linked door unlock-
ing function

68
1-3. Adjustable components (seats, mirrors, steering wheel)
IS250/220d/200d_EE
Linking driving position memory with door unlock operation
Record your driving position to button “1”, “2” or “3” before per-
forming the following.
Carry only the key (including the card key
) to which you want to
link the driving position. If 2 or more keys are in the vehicle, the
driving position cannot be linked properly.

: If equipped
Using the wireless remote control
Turn the “ENGINE START STOP” switch OFF and close
the driver's door.
Press and hold the desired but-
ton (“1”, “2” or “3”) while
pressing on the wireless
remote control until the signal
beeps.
The driving position is recalled
when the driver's door is
unlocked using the entry func-
tion or wireless remote control
and the driver's door is opened.
To prevent unintended triggering of the alarm, open and close a
door once after a driving position has been recorded. (If a door is
not opened within 30 seconds after is pressed, the doors will be
locked again and the alarm will automatically be set.)
In case that the alarm is triggered, immediately stop the alarm.
(P. 102)
STEP1
STEP2

69
1
1-3. Adjustable components (seats, mirrors, steering wheel)
Before driving
IS250/220d/200d_EEUsing the door lock switch
Turn the “ENGINE START STOP” switch OFF and close
the driver's door.
While pressing the desired but-
ton (“1”, “2” or “3”), press the
lock or unlock side on the
driver’s door lock switch until
the signal beeps.
The driving position is recalled
when the driver's door is
unlocked using the entry func-
tion or wireless remote control
and the driver's door is opened.
STEP1
STEP2

70
1-3. Adjustable components (seats, mirrors, steering wheel)
IS250/220d/200d_EE
Canceling the linked door unlock operation
Turn the “ENGINE START STOP” switch OFF and close the
driver's door.
Using the wireless remote control: While pushing the “SET” but-
ton, press on the wireless remote control until the signal
beeps.
Using the door lock switch: While pressing the “SET” button, press
the lock or unlock side on the door lock switch until the signal
beeps.
Operating the driving position memory after turning the “ENGINE START
STOP” switch OFF
Memorized positions (except for the steering wheel position) can be acti-
vated up to 180 seconds after the driver’s door is opened and another 60 sec-
onds after it is closed again, even after turning the “ENGINE START
STOP” switch OFF.
To cancel seat position recall
Perform any of the following operations.
Push the “SET” button.
Push button “1”, “2” or “3”.
Adjust the seat using the switches (only cancels seat position recall).
If the battery is disconnected
The memorized positions are erased when the battery is disconnected.
CAUTION
Seat adjustment caution
Take care during seat adjustment that the seat does not strike the rear pas-
senger or squeeze your body against the steering wheel.
STEP1
STEP2

80
1-3. Adjustable components (seats, mirrors, steering wheel)
IS250/220d/200d_EE
Steering wheel (power-adjustable type)
Auto tilt away
When the “ENGINE START
STOP” switch is turned OFF,
the steering wheel returns to its
stowed position by moving up
and away to enable easier
driver entry and exit.
Switching to ACCESSORY or
IGNITION ON mode will
return the steering wheel to the
original position.
The steering wheel can be adjusted to a comfortable position.
Up
Down
Away from the driver
Toward the driver

81
1-3. Adjustable components (seats, mirrors, steering wheel)
1
Before driving
IS250/220d/200d_EE
The steering wheel can be adjusted when
The “ENGINE START STOP” switch is in ACCESSORY or IGNITION
ON mode.
Automatic adjustment of the steering position (vehicles with driving posi-
tion memory)
A desired steering position can be entered to memory and recalled automat-
ically by the driving position memory. (P. 6 6 )
Customization that can be configured at any authorized Lexus dealer or
repairer, or another duly qualified and equipped professional
It is possible to deactivate the auto tilt-away function.
(Customizable featuresP. 556)
CAUTION
Caution while driving
Do not adjust the steering wheel while driving.
Doing so may cause the driver to mishandle the vehicle and cause an acci-
dent, resulting in death or serious injury.

82
1-3. Adjustable components (seats, mirrors, steering wheel)
IS250/220d/200d_EE
Anti-glare inside rear view mirror
Glare from the headlights of vehicles behind can be reduced by using
the following functions.
Manual anti-glare inside rear view mirror (if equipped)
Normal position
Anti-glare position
Auto anti-glare inside rear view mirror (if equipped)
In automatic mode, sensors are used to detect the headlights
of vehicles behind and automatically reduce the reflected
light.
Turns automatic mode on/off
The indicator comes on when
automatic mode is turned on.
The anti-glare mirror default
mode is automatic. The anti-
glare mirror is automatically
set to automatic whenever the
“ENGINE START STOP”
switch is turned to IGNI-