2011 Lexus IS F start stop button

39
1-2. Opening, closing and locking the doors and trunk
1
Before driving
IS F_EEEffective range (areas within which the electronic key is
detected)
When locking or unlock-
ing the doors
The system can be operated
when the electronic key is
within about 70 cm (2.3 ft.)
of either of the outside
front door handles. (Only
the doors detecting the key
can be operated.)
When unlocking the
trunk
The system can be operated
when the electronic key is
within about 70 cm (2.3 ft.)
of the trunk release button.
When starting the engine
or changing “ENGINE
START STOP” switch
modes
The system can be operated
when the electronic key is
inside the vehicle.

42
1-2. Opening, closing and locking the doors and trunk
IS F_EE
Switching the door unlock function
It is possible to set which doors the entry function unlocks.
Turn the “ENGINE START STOP” switch OFF.
Cancel the intrusion sensor of the alarm system to prevent unin-
tended triggering of the alarm during the setting change. (P. 97)
When the indicator on the key surface is turned off, push and
hold or for approximately 5 seconds while pushing
on the key.
The setting changes each time an operation is performed, as shown below.
(When changing the setting continuously, release the buttons, wait for at
least 5 seconds, and repeat step 3.)
To prevent unintended triggering of the alarm, unlock the doors using the
wireless remote control and open and close a door once after the settings
have been changed. (If a door is not opened within 30 seconds after is
pressed, the doors will be locked again and the alarm will automatically be
set.)
In case that the alarm is triggered, immediately stop the alarm. (P. 9 7 )
STEP1
STEP2
STEP3
Multi-informa-
tion displayUnlocking doorsBeep
Hold either front door han-
dle to unlock all doors.Exterior: Beeps twice
Interior: Pings once
Hold the driver's door han-
dle to unlock only the
driver's door.
Exterior: Beeps three
times
Interior: Pings once
Hold the front passenger’s
door handle to unlock all
doors.

55
1-2. Opening, closing and locking the doors and trunk
1
Before driving
IS F_EE
Locking the front doors from the outside without a key
Move the lock button to the lock position.
Close the door while pulling the door handle.
The door cannot be locked if the “ENGINE START STOP” switch
is in ACCESSORY or IGNITION ON mode, or the electronic key
is left inside the vehicle.
Depending on the position of the electronic key, the key may not be
detected correctly and the door may be locked.
Rear door child-protector lock
The door cannot be opened
from inside the vehicle when
the locks are set.
These locks can be set to pre-
vent children from opening the
rear doors. Push down on each
rear door switch to lock both
rear doors.
STEP1
STEP2

62
1-3. Adjustable components (seats, mirrors, steering wheel)
IS F_EE
Driving position memory (driver’s seat)
Your preferred driving position (the position of the driver's seat, steer-
ing wheel and outside rear view mirrors) can be memorized and
recalled with the touch of a button. It is also possible to set this func-
tion to activate automatically when the doors are unlocked.
Three different driving positions can be entered into memory.
Entering a position to memory
Turn the “ENGINE START STOP” switch to IGNITION
ON mode.
Adjust the driver’s seat, steering wheel, and outside rear
view mirrors to the desired positions.
Push the “SET” button, then
within 3 seconds push button
“1”, “2” or “3” until the sig-
nal beeps.
If the selected button has
already been preset, the pre-
viously recorded position
will be overwritten.
Recalling the memorized position
Check that the shift lever is set in P.
Turn the “ENGINE START STOP” switch to IGNITION
ON mode.
Push button “1”, “2” or “3”
to recall the memorized posi-
tion.
STEP1
STEP2
STEP3
STEP1
STEP2

63
1-3. Adjustable components (seats, mirrors, steering wheel)
1
Before driving
IS F_EE
Linking driving position memory with door unlock operation
Record your driving position to button “1”, “2” or “3” before per-
forming the following.
Using the wireless remote control
Turn the “ENGINE START STOP” switch OFF and close
the driver's door.
While pressing the desired but-
ton (“1”, “2” or “3”), push
on the wireless remote control
until the signal beeps.
The driving position is recalled
when the driver's door is
unlocked using the entry func-
tion or wireless remote control
and the driver's door is opened.
To prevent unintended triggering of the alarm, open and close a
door once after a driving position has been recorded. (If a door is
not opened within 30 seconds after is pressed, the doors will be
locked again and the alarm will automatically be set.)
In case that the alarm is triggered, immediately stop the alarm.
(P. 9 7 )
STEP1
STEP2

64
1-3. Adjustable components (seats, mirrors, steering wheel)
IS F_EEUsing the door lock switch
Carry only the key (including the card key
) to which you want
to link the driving position. If 2 or more keys are in the vehicle,
the driving position cannot be linked properly.
Turn the “ENGINE START STOP” switch OFF and close
the driver's door.
While pressing the desired but-
ton (“1”, “2” or “3”), press the
lock or unlock side on the
driver’s door lock switch until
the signal beeps.
The driving position is recalled
when the driver's door is
unlocked using the entry func-
tion or wireless remote control
and the driver's door is opened.
: If equipped
STEP1
STEP2
Canceling the linked door unlock operation
Turn the “ENGINE START STOP” switch OFF and close the
driver's door.
Using the wireless remote control: While pushing the “SET” but-
ton, press on the wireless remote control until the signal
beeps.
Using the door lock switch: While pressing the “SET” button, press
the lock or unlock side on the door lock switch until the signal
beeps.
Operating the driving position memory after turning the “ENGINE START
STOP” switch OFF
Memorized positions (except for the steering wheel position) can be acti-
vated up to 180 seconds after the driver’s door is opened and another 60 sec-
onds after it is closed again, even after turning the “ENGINE START
STOP” switch OFF.
STEP1
STEP2

66
1-3. Adjustable components (seats, mirrors, steering wheel)
IS F_EE
Seat position memory (front passenger’s seat)
Your preferred front passenger seat position can be memorized and
recalled with the touch of a button.
Three different seat positions can be entered into memory.
Entering a position to memory
Turn the “ENGINE START STOP” switch to IGNITION
ON mode.
Adjust the front passenger seat to the desired position.
Push the “SET” button, then
within 3 seconds push button
“1”, “2” or “3” until the sig-
nal beeps.
If the selected button has
already been preset, the pre-
viously recorded position
will be overwritten.
Recalling the memorized position
Check that the shift lever is set in P.
Push button “1”, “2” or “3”
to recall the memorized posi-
tion.
STEP1
STEP2
STEP3

67
1-3. Adjustable components (seats, mirrors, steering wheel)
1
Before driving
IS F_EE
Operating the seat position memory after turning the “ENGINE START
STOP” switch OFF
Memorized position can be activated up to 180 seconds after the front pas-
senger door is opened, even after turning the “ENGINE START STOP”
switch OFF.
To cancel seat position recall
Perform any of the following operations.
Push the “SET” button.
Push button “1”, “2” or “3”.
Adjust the seat position using the switches.
If the battery is disconnected
The memorized positions are erased when the battery is disconnected.
CAUTION
Seat adjustment caution
Take care during seat adjustment that the seat does not strike the rear pas-
senger.