2011 Lexus HS250h turn signal

476
4-3. Do-it-yourself maintenance
LED headlights
■Rear bulb locations
Front fog light
Front turn signal light
Parking lightFront side marker light
Headlight high beam and
daytime running light
Rear turn signal light
Back-up light
License plate light

479
4-3. Do-it-yourself maintenance
4
Maintenance and care
■Front turn signal lights (halogen headlights)
Turn the bulb base counterclock-
wise.
Remove the light bulb.
■ Front turn signal lights (LED headlights)
Turn the bulb base counterclock-
wise.
Remove the light bulb.

484
4-3. Do-it-yourself maintenance
■Rear turn signal lights
Open the trunk lid and remove the
cover.
To prevent damage to the rear
combination assembly, cover the
tip of the screwdriver with a rag.
Remove the bolts, stopper rubber
and rear combination assembly.
Turn the bulb base counterclock-
wise.
Remove the light bulb.

485
4-3. Do-it-yourself maintenance
4
Maintenance and care
■Lights other than the above
If any of the lights listed below ha s burnt out, have it replaced by your
Lexus dealer.
● Headlight low beams (LED headlight type)
● Side turn signal lights
● Stop/tail lights
● Tail lights
● Rear side marker lights
● High mounted stoplight
● Outer foot lights
■When replacing the front right headlight, front turn signal li ghts and parking light
bulbs
■LED light bulbs
The headlight low beams (LED headlights ty pe), side turn signal lights, rear side
marker lights, stop/tail lights, tail lights and high mounted stoplight consist of a num-
ber of LEDs. If any of the LEDs burn out, take your vehicle to your Lexus dealer to
have the light replaced.
Remove the securing clip and move the
washer fluid filler opening to allow easy
access to the light bulbs.
After replacing the bulbs, make sure to
secure the washer fluid filler opening with the
clip.

488
5-1. Essential information
Emergency flashers
NOTICE
■To prevent 12-volt battery discharge
Do not leave the emergency flashers on longer than necessary when the hybrid sys-
tem is not operating.
Use the emergency flashers if the vehicle malfunctions or is involved in an
accident.
Press the switch to flash all the
turn signal lights. To turn them
off, press the switch once again.

504
5-2. Steps to take in an emergency
The tire pressure warning system may be disabled in the following conditions:
(When the condition becomes normal, the system will work properly.)
●If electronic devices or facilities using similar radio wave frequencies are nearby.
●If a radio set at similar frequency is in use in the vehicle.
●If a window tint that affects the radio wave signals is installed.
●If there is a lot of snow or ice on the vehicle, particularly around the wheels or
wheel housings.
●If non-genuine Lexus wheels are used (Even if you use Lexus wheels, the tire
pressure warning system may not work properly with some types of tires.)
●If tire chains are used.
■If the tire pressure warning light comes on after flashing frequently for 1 minute
If the tire pressure warning light comes on after flashing frequently for 1 minute
when the “POWER” switch is turned to ON mode, have it checked by your Lexus
dealer.
■Customization that can be configured at Lexus dealer
The vehicle speed linked seat belt reminder buzzer can be disabled.
(Customizable features P. 5 8 0 )
CAUTION
■When the electric power steering system warning light comes on
The steering wheel may become extremely heavy.
If the steering wheel becomes heavier than usual when operating, hold firmly and
operate it using more force than usual.
■If the tire pressure warning light comes on
Be sure to observe the following precautions. Failure to do so could cause loss of
vehicle control and result in death or serious injury.
●Stop your vehicle in a safe place as soon as possible. Adjust the tire inflation pres-
sure immediately.
●If the tire pressure warning light comes on even after tire inflation pressure adjust-
ment, it is probable that you have a flat tire. Check the tires. If a tire is flat, change
it with the spare tire and have the flat tire repaired by the nearest Lexus dealer.

564
6-1. Specifications
Light bulbs
A: HB3 halogen bulbs
B: Double end bulbs
C: Wedge base bulbs (clear)
D: Wedge base bulbs (amber)
E: H11 halogen bulbs
F: Single end bulbs
Light BulbsBulb No.WTy p e
Exterior
LED headlightsHigh beam
Halogen headlights
High beam
Low beam
9005
9005 H1160
6055A
A E
Front side marker lightsW5W5C
Front turn signal lights3457NA28 /8F
Parking lightsW5W5C
Front fog lightsH1155E
Rear turn signal lightsWY21W21D
Back-up lightsW16W16C
License plate lightsW5W5C
Outer foot lights5C
Interior
Vanity lights8C
Front interior lights/Personal lights8C
Rear interior light8B
Trunk light3.8C
Door courtesy lights5C

590
6-2. Customization
Multi-information display (P. 1 7 2 )
Settings that can be changed using the multi-information switches
Available unitsmiles (MPG), km (km/l), km (l/100 km)
Available languagesEnglish, French and Spanish
■Vehicle customization
●When the “Speed-detecting automatic door lock function” and “Selecting other
than P position locks all d oors” are both on, the door lock operates as follows.
• When any one of the shift position indicato rs other than P is illuminated, all the
doors will be locked.
• If the vehicle is started with all the doors locked, the “Speed-detecting auto- matic door lock function” would not operate.
• If the vehicle is started with any door unlocked, the “Speed-detecting auto-
matic door lock function” will operate.
●When the smart access syst em with push-button start is off, the “Smart door
unlocking function” cannot be customized.
●When the doors remain closed after unlocking the doors and the “Automatic
door lock function” activates, the signals will be generated in accordance with
the “Operation signal (emergency flashers)” and the “Operation signal (buzzer
volume)” settings.
■In the following situations, customize mode in which the settings can be changed
through the multi-information switches will automatically be turned off.
●A warning message appears after the customize mode screen is displayed.
●The “POWER” switch is turned off.
●The vehicle begins to move while the customize mode screen is displayed.