2011 Lexus CT200h Hybrid system

5
619
5-2. Steps to take in an emergency
When trouble arises
CT200h_EE (OM76041E)
Stopping the hybrid system
Set the parking brake, shift the shift position to P and press the “POWER”
switch as you normally do when stopping the hybrid system.
Replacing the key battery
As the above procedure is a temporary measure, it is recommended that the
electronic key battery be replaced immediately when the battery is depleted.
(P. 515)
Alarm
Using the mechanical key to lock the doors will not set the alarm system.
If a door is unlocked using the mechanical key when the alarm system is set,
the alarm may be triggered.

620
5-2. Steps to take in an emergency
CT200h_EE (OM76041E)
If the 12-volt battery is discharged
The following procedures may be used to start the hybrid system if the
vehicle’s 12-volt battery is discharged.
You can also call any authorized Lexus dealer or repairer, or another
duly qualified and equipped professional.
If you have a set of jumper (or booster) cables and a second
vehicle with a 12-volt battery, you can jump start your vehicle
by following the steps below.
Open the hood and fuse
block cover.
Open the exclusive jump
starting terminal cover.
STEP1
STEP2

622
5-2. Steps to take in an emergency
CT200h_EE (OM76041E)
Start the engine of the second vehicle. Increase the
engine speed slightly and maintain at that level for
approximately 5 minutes to recharge the battery of your
vehicle.
Open and close any of the doors of your vehicle with the
“POWER” switch off.
Maintain the engine speed of the second vehicle and start
the hybrid system of your vehicle by turning the
“POWER” switch to ON mode.
Make sure the “READY” indicator light comes on. If the
indicator light does not come on, contact any authorized
Lexus dealer or repairer, or another duly qualified and
equipped professional.
Once the hybrid system has started, remove the jumper
cables in the exact reverse order from which they were
connected.
To install the engine cover, conduct the removal proce-
dure in reverse. After installing, check that the fixed pins
are inserted securely.
Once the hybrid system starts, have the vehicle inspected at any
th i d L d l i th d l lifi dSTEP4
STEP5
STEP6
STEP7
STEP8
STEP9

5
623
5-2. Steps to take in an emergency
When trouble arises
CT200h_EE (OM76041E)
Starting the hybrid system when the 12-volt battery is discharged
The hybrid system cannot be started by push-starting.
To prevent 12-volt battery discharge
Turn off the headlights and the audio system while the hybrid system is
off.
Turn off any unnecessary electrical components when the vehicle is run-
ning at a low speed for an extended period, such as in heavy traffic.
When the 12-volt battery is removed or discharged
The hybrid system may not start. (P. 499)
If the 12-volt battery discharges while the shift position is in P, it may not
be possible to shift the shift position to other positions. In this case, the
vehicle cannot be towed without lifting both front wheels because the
front wheels will be locked. (P. 551)
When the 12-volt battery is reconnected, start the hybrid system and
confirm that the shift position can be changed to each position using the
shift position indicator.
Charging the 12-volt battery
The electricity stored in the 12-volt battery will discharge gradually even
when the vehicle is not in use, due to natural discharge and the draining
effects of certain electrical appliances. If the vehicle is left for a long time,
the 12-volt battery may discharge, and the hybrid system may be unable to
start. (The 12-volt battery recharges automatically while the hybrid system
is operating.)

5
627
5-2. Steps to take in an emergency
When trouble arises
CT200h_EE (OM76041E)
If your vehicle overheats
Correction procedures
If the high coolant temperature warning light comes on or
flashes
Stop the vehicle in a safe place and turn off the air condi-
tioning system.
Check to see if steam is coming out from the engine area.
If you see steam:
Stop the hybrid system. Carefully lift the hood after the
steam subsides and then restart the hybrid system.
If you do not see steam:
Leave the hybrid system operating and carefully lift the
hood.
Check to see if the cooling fans are operating.
If the fans are operating:
Wait until the high coolant temperature warning light goes
off and then stop the hybrid system.
If the fans are not operating:
Stop the hybrid system immediately and call any authorized
Lexus dealer or repairer, or another duly qualified and
equipped professional.
The following may indicate that your vehicle is overheating:
The high coolant temperature warning light comes on or
flashes:
The engine may be overheating.
“HYBRID SYSTEM OVERHEAT” is shown on the multi-
information display:
STEP1
STEP2
STEP3

628
5-2. Steps to take in an emergency
CT200h_EE (OM76041E)After the hybrid system has
cooled down sufficiently, check
the engine coolant level and
inspect the cooling system for
leaks.
If the engine compartment
cover needs to be removed: P.
486
Add engine coolant if neces-
sary.
Water can be used in an emer-
gency if engine coolant is
unavailable. (P. 645)
Have the vehicle inspected at the nearest authorized Lexus dealer
or repairer, or another duly qualified and equipped professional as
soon as possible.
STEP4
STEP5

5
629
5-2. Steps to take in an emergency
When trouble arises
CT200h_EE (OM76041E)If “HYBRID SYSTEM OVERHEAT” is shown on the multi-
information display
Stop the vehicle in a safe place and turn off the air condi-
tioning system.
Leave the hybrid system operating and carefully lift the
hood.
Check if the cooling fans are operating.
If the fans are operating:
Wait until the “HYBRID SYSTEM OVERHEAT” message
disappears and then stop the hybrid system.
If the message does not disappear, call any authorized
Lexus dealer or repairer, or another duly qualified and
equipped professional.
If the fans are not operating:
Stop the hybrid system immediately and call any authorized
Lexus dealer or repairer, or another duly qualified and
equipped professional.
After the hybrid system has
cooled down, check the power
control unit coolant level and
inspect the cooling system for
leaks.
If the engine compartment
cover needs to be removed: P.
486
STEP1
STEP2
STEP3
STEP4

630
5-2. Steps to take in an emergency
CT200h_EE (OM76041E)Add power control unit coolant
if necessary.
Water can be used in an emer-
gency if power control unit
coolant is unavailable. (P.
645)
Have the vehicle inspected at the nearest authorized Lexus dealer
or repairer, or another duly qualified and equipped professional as
soon as possible.
STEP5
Overheating
The following symptoms may occur when your vehicle is overheating:
Hybrid system output decreases.
Steam comes out from under the hood.