2011 JEEP GRAND CHEROKEE remove seats

•If the liftgate handle is pulled while the
power liftgate is closing, the liftgate will
reverse to the full open position.
• If the liftgate handle is pulled while the
power liftgate is opening, the liftgate mo-
tor will disengage to allow manual opera-
tion.
• The power liftgate buttons will not oper-
ate if the vehicle is in gear or the vehicle
speed is above 0 mph (0 km/h).
• The power liftgate will not operate in tem-
peratures below 22°F ( 30°C) or tem-
peratures above 150°F (65°C). Be sure to
remove any buildup of snow or ice from
the liftgate before pressing any of the
power liftgate switches.
•
If the power liftgate encounters multiple
obstructions within the same cycle, the
system will automatically stop and the lift-
gate must be opened or closed manually.
• If your liftgate is power closing and you
put the vehicle in gear, the liftgate will
continue to power close. However, ve-
hicle movement may result in a detection
of an obstruction.
WARNING!
• Driving with the liftgate open can allow
poisonous exhaust gases into your vehicle.
You and your passengers could be injured
by these fumes. Keep the liftgate closed
when you are operating the vehicle.
• If you are required to drive with the liftgate
open, make sure that all windows are
closed, and the climate control blower
switch is set at high speed. Do not use the
recirculation mode.
Gas props support the liftgate in the open
position. However, because the gas pressure
drops with temperature, it may be necessary to
assist the props when opening the liftgate in
cold weather.
OCCUPANT RESTRAINTSSome of the most important safety features in
your vehicle are the restraint systems:
• Three-point lap and shoulder belts for the
driver and all passengers •
Advanced Front Airbags for driver and front
passenger
• Supplemental Active Head Restraints (AHR)
located on top of the front seats (integrated
into the head restraint)
• Supplemental driver side knee airbag
• Supplemental Side Airbag Inflatable Cur-
tains (SABIC) for the driver and passengers
seated next to a window — if equipped
• Supplemental Seat-Mounted Side Airbags
(SAB) — if equipped
• An energy-absorbing steering column and
steering wheel
• Knee bolsters/blockers for front seat occu-
pants
• Front seat belts incorporate pretensioners to
enhance occupant protection by managing
occupant energy during an impact event
•
All seat belt systems (except the driver’s)
include Automatic Locking Retractors (ALRs),
which lock the seat belt webbing into position
by extending the belt all the way out and then
28

IL = Suitable for particular ISOFIX child restraint
systems (CRS) given in the attachment list.
These ISOFIX CRS are those of the “specific
vehicle”, “restricted” or “semi-universal” cat-
egories.
X = ISOFIX position not suitable for ISOFIX
child restraint systems in this mass group
and/or this size class.
Children 12 years and under should ride prop-
erly buckled up in a rear seat, if available.
According to crash statistics, children are safer
when properly restrained in the rear seats
rather than in the front.
There are different sizes and types of restraints
for children from newborn size to the child
almost large enough for an adult safety belt.
Always check the child seat Owner’s Manual to
ensure you have the right seat for your child.
Use the restraint that is correct for your child.WARNING!
In an collision, an unrestrained child, even a
tiny baby, can become a projectile inside the
vehicle. The force required to hold even an
infant on your lap can become so great that
you could not hold the child, no matter how
strong you are. The child and others could be
badly injured. Any child riding in your vehicle
should be in a proper restraint for the child’s
size.
Infants and Child Restraints
• Safety experts recommend that children ride
rearward-facing in the vehicle until they are
at least one year old and weigh at least
20 lbs (9 kg). Two types of child restraints
can be used rearward-facing: infant carriers
and convertible child seats.
• The infant carrier is only used rearward-
facing in the vehicle. It is recommended for
children who weigh up to about 20 lbs (9 kg).
Convertible child seats often have a higher
weight limit in the rearward-facing direction
than infant carriers do, so they can be used rearward-facing by children who weigh more
than 20 lbs (9 kg) but are less than one year
old. Both types of child restraints are held in
the vehicle by the lap/shoulder belt or the
ISOFIX child restraint anchorage system
(Refer to “ISOFIX — Child Seat Anchorage
System”)
When using certain Child Restraint Systems
with rigid attachments ISOFIX and foot stands
extending to the vehicle floor, remove the ve-
hicle floor mat prior to installation to ensure a
secure fit. Refer to the Child Restraint Owner’s
Manual for additional information.
WARNING!
• Rearward-facing child seats must never be
used in the front seat of a vehicle with the
front passenger airbag unless the airbag is
turned off. An airbag deployment could
cause severe injury or death to infants in
this position.
(Continued)
48

remove it from the vehicle. Do not leave it
loose in the vehicle. In a sudden stop or
accident, it could strike the occupants or
seatbacks and cause serious personal in-
jury.
Older Children and Child Restraints
Children who weigh more than 20 lbs (9 kg),
and who are older than one year, can ride
forward-facing in the vehicle. Forward-facing
child seats and convertible child seats used in
the forward-facing direction are for children
who weigh 20 to 40 lbs (9 to 18 kg), and who
are older than one year. These child seats are
also held in the vehicle by the lap/shoulder belt
or the ISOFIX child restraint anchorage system
(Refer to “ISOFIX — Child Seat Anchorage
System”)
The belt-positioning booster seat is for children
weighing more than 40 lbs (18 kg), but who are
still too small to fit the vehicle’s seat belts
properly. If the child cannot sit with knees bent
over the vehicle’s seat cushion while the child’s
back is against the seatback, they should use a
belt-positioning booster seat. The child and
belt-positioning booster seat are held in the
vehicle by the lap/shoulder belt. Children Too Large for Booster Seats
Children who are large enough to wear the
shoulder belt comfortably, and whose legs are
long enough to bend over the front of the seat
when their back is against the seatback, should
use the lap/shoulder belt in a rear seat.
•
Make sure that the child is upright in the seat.
• The lap portion should be low on the hips
and as snug as possible.
• Check belt fit periodically. A child’s squirm-
ing or slouching can move the belt out of
position.
• If the shoulder belt contacts the face or neck,
move the child closer to the center of the
vehicle. Never allow a child to put the shoul-
der belt under an arm or behind the back.
ISOFIX — Child Seat Anchorage System
Your vehicle’s rear seat is equipped with the
child restraint anchorage system called ISO-
FIX. The ISOFIX system provides for the instal-
lation of the child restraint without using the
vehicle’s seat belts, instead securing the child restraint using lower anchorages and upper
tether straps from the child restraint to the
vehicle structure.
ISOFIX-compatible child restraint systems are
now available. Child restraints having tether
straps and hooks for connection to the top
tether anchorages, have been available for
some time. You are urged to take advantage of
all the available attachments provided with your
child restraint in any vehicle.
NOTE:
When using the ISOFIX attaching system to
install a child restraint, please ensure that
all seat belts not being used for occupant
restraints are stowed and out of reach of
children. Remind all children in the vehicle
that the seat belts are not toys and should
not be played with, and never leave your
child unattended in the vehicle.
The two outboard rear seating positions have
anchorages, child seats with fixed lower at-
tachments must be installed in the outboard
positions only. Regardless of the specific type
of lower attachment, never install ISOFIX-
50

Ventilated Seats — If EquippedOn some models, both the driver and passen-
ger seats are ventilated. Located in the seat
cushion and seatback are small fans that draw
the air from the passenger compartment and
blow air through fine perforations in the seat
cover to help keep the driver and front passen-
ger cooler in higher ambient temperatures.
There are two ventilated seat switches that
allow the driver and passenger to operate the
seats independently. The ventilated seat
switches are located on the switch bank in the
center stack of the instrument panel, just below
the climate controls.The ventilated seat
switches are used to
control the speed of the
fans located in the seat.
Press the switch once
to choose HIGH, press
it a second time to
choose LOW. Pressing
the switch a third time
will turn the ventilated
seat OFF. When HIGH speed is selected both lights on the switch will be illuminated. When
LOW speed is selected one light will be illumi-
nated.
NOTE:
The engine must be running for the venti-
lated seats to operate.
Vehicles Equipped with Remote Start
On models that are equipped with remote start,
the driver’s ventilated seat can be programmed
to come on during a remote start. Refer to
“Remote Starting System — If Equipped” in
“Things to Know Before Starting Your Vehicle”
for further information.
Head RestraintsHead restraints are designed to reduce the risk
of injury by restricting head movement in the
event of a rear-impact. Head restraints should
be adjusted so that the top of the head restraint
is located above the top of your ear.
WARNING!
The head restraints for all occupants must be
properly adjusted prior to operating the ve-
hicle or occupying a seat. Head restraints
should never be adjusted while the vehicle is
in motion. Driving a vehicle with the head
restraints improperly adjusted or removed
could cause serious injury or death in the
event of a collision.
Active Head Restraints — Front Seats
Active Head Restraints are passive, deployable
components, and vehicles with this equipment
cannot be readily identified by any markings,
only through visual inspection of the head re-
straint. The head restraint will be split in two
halves, with the front half being soft foam and
trim, the back half being decorative plastic.
When AHRs deploy during a rear impact, the
front half of the head restraint extends forward
to minimize the gap between the back of the
occupant’s head and the AHR. This system is
designed to help prevent or reduce the extent
of injuries to the driver and front passenger in
certain types of rear impacts. Refer to “Occu-
99

Retractable Cargo Area Cover —
If Equipped
NOTE:
The purpose of this cover is for privacy, not
to secure loads. It will not prevent cargo
from shifting or protect passengers from
loose cargo.
To cover the cargo area:
1. Grasp the cover at the center handle. Pull it
over the cargo area.
2. Insert the pins on the ends of the cover into
the slots in the pillar trim cover.3. The liftgate may be opened with the cargo
cover in place.WARNING!
In a collision, a loose cargo cover in the
vehicle could cause injury. It could fly around
in a sudden stop and strike someone in the
vehicle. Do not store the cargo cover on the
cargo floor or in the passenger compartment.
Remove the cover from the vehicle when
taken from its mounting. Do not store it in the
vehicle.
Cargo Tie-Down HooksThe cargo tie-downs, located on the cargo area
floor, should be used to safely secure loads
when the vehicle is moving.
WARNING!
•
To help protect against personal injury,
passengers should not be seated in the
rear cargo area. The rear cargo space is
intended for load carrying purposes only,
not for passengers, who should sit in seats
and use seat belts.
(Continued)
Lower Storage Bins
Rear Cargo Cover
Cargo Tie-Down Hooks
149

hicle repaired as soon as possible. The cost
of such repairs is considered the responsi-
bility of the owner.
• If you carry special cargo such as chemi-
cals, fertilizers, de-icer salt, etc., assure that
such materials are well packaged and
sealed.
• If a lot of driving is done on gravel roads,
consider mud or stone shields behind each
wheel.
• Use MOPAR Touch Up Paint or equivalent
on scratches or chips as soon as possible.
Your authorized dealer has touch up paint to
match the color of your vehicle.
Wheel and Wheel Trim Care
All wheels and wheel trim, especially aluminum
and chrome-plated wheels should be cleaned
regularly with a mild soap and water to prevent
corrosion. To remove heavy soil, use MOPAR 
Wheel Cleaner or select a nonabrasive, non-
acidic cleaner. Do not use scouring pads, steel
wool, a bristle brush or metal polishes. Only
MOPAR cleaners or equivalent are recom-
mended. Do not use oven cleaner. Avoid auto- matic car washes that use acidic solutions or
harsh brushes that may damage the wheels’
protective finish.
Stain Repel Fabric Cleaning Procedure –
If Equipped
Stain Repel seats may be cleaned in the follow-
ing manner:
•
Remove as much of the stain as possible by
blotting with a clean, dry towel.
• Blot any remaining stain with a clean, damp
towel.
• For tough stains, apply MOPAR Total Clean
or a mild soap solution to a clean, damp
cloth and remove the stain. Use a fresh,
damp towel to remove soap residue.
• For grease stains, apply MOPAR Multi-
Purpose Cleaner or equivalent to a clean,
damp cloth and remove the stain. Use a
fresh, damp towel to remove soap residue.
• Do not use any harsh solvents or any other
form of protectants on Stain Repel products. Interior Care
Use MOPAR
Total Clean or equivalent to clean
fabric upholstery and carpeting.
Interior Trim should be cleaned starting with a
damp cloth, a damp cloth with MOPAR Total
Clean or equivalent, then MOPAR Spot & Stain
Remover or equivalent, if absolutely necessary.
Do not use harsh cleaners or Armor All . Use
MOPAR Total Clean or equivalent to clean
vinyl upholstery.
Leather Seat Care And Cleaning
MOPAR Total Clean or equivalent is specifi-
cally recommended for leather upholstery.
Your leather upholstery can be best preserved
by regular cleaning with a damp soft cloth.
Small particles of dirt can act as an abrasive
and damage the leather upholstery and should
be removed promptly with a damp cloth. Stub-
born soils can be removed easily with a soft
cloth and MOPAR Total Clean or equivalent.
Care should be taken to avoid soaking your
leather upholstery with any liquid. Please do
not use polishes, oils, cleaning fluids, solvents,
detergents, or ammonia-based cleaners to
288