2011 JEEP GRAND CHEROKEE key fob

CAUTION!(Continued)
• Do not shift from REVERSE, PARK, or
NEUTRAL into any forward gear when the
engine is above idle speed.
• Before shifting into any gear, make sure
your foot is firmly on the brake pedal.
WARNING!
It is dangerous to move the shift lever out of
PARK or NEUTRAL if the engine speed is
higher than idle speed. If your foot is not firmly
on the brake pedal, the vehicle could acceler-
ate quickly forward or in reverse. You could
lose control of the vehicle and hit someone or
something. Only shift into gear when the
engine is idling normally and when your foot is
firmly on the brake pedal.
Key Ignition Park InterlockThis vehicle is equipped with a Key Ignition
Park Interlock which requires the shift lever to
be placed in PARK prior to turning the ignition
switch to the LOCK position. The key fob can
only be removed from the ignition switch when the ignition switch is in the LOCK position and
once removed the shift lever is locked in PARK.
Brake/Transmission Shift Interlock
System
This vehicle is equipped with a Brake Transmis-
sion Shift Interlock System (BTSI) that holds the
shift lever in the PARK position when the igni-
tion switch is in the LOCK position. To move the
shift lever out of the PARK position, the ignition
switch must be turned to the ON or START
position (engine running or not) and the brake
pedal must be pressed.
Brake/Transmission Interlock
Manual Override
Your vehicle may be equipped with a shift lock
manual override. The manual override may be
used in the event that the shift lever should fail
to move from PARK with the ignition switch in
the ON position and the brake pedal pressed.
To operate the shift lock manual override, per-
form the following steps:
1. Turn the ignition switch to the ON position
without starting the engine.
2. Firmly set the parking brake.
3. Remove the rubber liner from the cupholder
(located next to the shifter on the center con-
sole).
4. Using a flat-bladed screwdriver, carefully
remove the shift lock manual override cover,
which is located on the bottom of the cup-
holder.
5. Press and maintain firm pressure on the
brake pedal.
6. Using the screwdriver, reach into the manual
override opening. Press and hold the shift lock
lever down.
7. Move the shift lever into the NEUTRAL posi-
tion.
8. The vehicle may then be started in NEU-
TRAL.
Have your vehicle inspected by your local
authorized dealer if the shift lock manual over-
ride has been used.
205

•This light only shows that the parking
brake is applied. It does not show the
degree of brake application.
When parking on a hill, it is important to turn the
front wheels toward the curb on a downhill
grade and away from the curb on an uphill
grade. Apply the parking brake before placing
the shift lever in PARK, otherwise the load on
the transmission locking mechanism may make
it difficult to move the shift lever out of PARK.
The parking brake should always be applied
whenever the driver is not in the vehicle.
WARNING!
• Never use the PARK position as a substi-
tute for the parking brake. Always apply the
parking brake fully when parked to guard
against vehicle movement and possible
injury or damage.
•
Never leave children alone in a vehicle.
Leaving unattended children in a vehicle is
dangerous for a number of reasons. A child
or others could be seriously or fatally injured.
(Continued)
WARNING! (Continued)
• Do not leave the key fob in the ignition
switch. A child could operate power win-
dows, other controls, or move the vehicle.
• Be sure the parking brake is fully disen-
gaged before driving; failure to do so can
lead to brake failure and a collision.
• Always fully apply the parking brake when
leaving your vehicle, or it may roll and
cause damage or injury. Also be certain to
leave the transmission in PARK. Failure to
do so may allow the vehicle to roll and
cause damage or injury.
CAUTION!
If the “Brake Warning Light” remains on with
the parking brake released, a brake system
malfunction is indicated. Have the brake sys-
tem serviced by an authorized dealer imme-
diately.
ELECTRONIC BRAKE CONTROL
SYSTEM
Your vehicle is equipped with an advanced
electronic brake control system that includes
the Anti-Lock Brake System (ABS), Traction
Control System (TCS), Brake Assist System
(BAS), Electronic Roll Mitigation (ERM), and
Electronic Stability Control (ESC). All five of
these systems work together to enhance ve-
hicle stability and control in various driving
conditions.
Also, your vehicle is equipped with Trailer Sway
Control (TSC), Hill Start Assist (HSA), Brake
Lock Differential (BLD), Ready Alert Braking,
Rain Brake Support and, if it has four-wheel
drive with the MP 3023 two-speed transfer
case, Hill Descent Control (HDC).
Anti-Lock Brake System (ABS)
This system aids the driver in maintaining ve-
hicle control under adverse braking conditions.
The system controls hydraulic brake pressure
to prevent wheel lock-up and help avoid skid-
ding on slippery surfaces during braking.
223

2. Turn OFF the ignition.
3. For vehicles with Keyless Enter-N-Go, re-
move the Keyless Enter-N-Go button and use
the key fob to complete this procedure. Refer to
“Starting Procedures/Keyless Enter-N-Go” in
“Starting and Operating” for further information.
4. Turn the ignition switch to the ON/RUN po-
sition, but do not start the engine.
5. Press and hold the brake pedal.
6. Shift the transmission into NEUTRAL.
7. Using the point of a ballpoint pen or similar
object, press and hold the recessed transfer
case N (Neutral) button (located by the selector
switch) for four seconds, until the light behind
the N symbol starts to blink, indicating shift in
progress. The light will stop blinking (stay on
solid) when the shift to N (Neutral) is complete.
A “FOUR WHEEL DRIVE SYSTEM IN NEU-
TRAL” message will display on the EVIC (Elec-
tronic Vehicle Information Center). Refer to
“Electronic Vehicle Information Center (EVIC)”
in “Understanding Your Instrument Panel” for
further information.8. Start the engine.
9. Shift the transmission into REVERSE.
10. Release the brake pedal for five seconds
and ensure that there is no vehicle movement.
11. Turn OFF the engine and leave the ignition
switch in the unlocked OFF position.
12. Firmly apply the parking brake.
13. Shift the transmission into PARK.CAUTION!
Damage to the transmission may occur if the
transmission is shifted into PARK with the
transfer case in NEUTRAL (N) and the engine
running. With the transfer case in NEUTRAL
(N) ensure that the engine is off prior to
shifting the transmission into PARK.
14. Attach the vehicle to the tow vehicle using
a suitable tow bar.
15. Release the parking brake.
16. Disconnect the negative battery cable, and
secure it away from the negative battery post.
NOTE:
• Steps 1 through 6 are requirements that
must be met prior to pressing the NEU-
TRAL (N) button, and must continue to be
met until the four seconds elapse and the
shift has been completed. If any of these
requirements are not met prior to press-
ing the NEUTRAL (N) button or are no
longer met during the four second timer,
then the NEUTRAL (N) indicator light will
Neutral Switch
253

flash continuously until all requirements
are met or until the NEUTRAL (N) button is
released.
• The ignition switch must be in the ON/
RUN position for a shift to take place and
for the position indicator lights to be op-
erable. If the ignition switch is not in the
ON/RUN position, the shift will not take
place and no position indicator lights will
be on or flashing.
• A flashing NEUTRAL (N) position indica-
tor light indicates that shift requirements
have not been met.
Shifting Out Of NEUTRAL (N)
Use the following procedure to prepare your
vehicle for normal usage.
1. Bring the vehicle to a complete stop, leaving
it connected to the tow vehicle.
2. Firmly apply the parking brake.
3. Reconnect the negative battery cable. 4. Turn the key fob to the LOCK/OFF position (if
it has been moved or the engine has been
started).
5. Turn the key fob to the ON/RUN position, but
do not start the engine.
6. Press and hold the brake pedal.
7. Shift the transmission into NEUTRAL.
8. Using the point of a ballpoint pen or similar
object, press and hold the recessed transfer
case N (Neutral) button (located by the selector
switch) for four seconds, until the light behind
the N symbol starts to blink, indicating shift in
progress. The light will stop blinking (go out)
when shift is complete. The “FOUR WHEEL
DRIVE SYSTEM IN NEUTRAL” message will no
longer be displayed on the EVIC (Electronic
Vehicle Information Center). Refer to “Elec-
tronic Vehicle Information Center (EVIC)” in
“Understanding Your Instrument Panel” for fur-
ther information.
NOTE:
When shifting out of transfer case NEUTRAL
(N), turning the engine OFF may be required
to avoid gear clash.
Neutral Switch
254

6
WHAT TO DO IN EMERGENCIES
•HAZARD WARNING FLASHERS ................. 258
• IF YOUR ENGINE OVERHEATS .................. 258
• JACKING AND TIRE CHANGING ................. 259
• Jack Location .......................... 259
• Spare Tire Stowage ....................... 259
• Preparations for Jacking .................... 259
• Jacking Instructions ...................... 260
• JUMP-STARTING .......................... 262
• Preparations for Jump-Start .................. 262
• Jump-Starting Procedure ................... 263
• TOW EYES .............................. 264
• TOWING A DISABLED VEHICLE ................. 265
• Towing Without the Ignition Key Fob ............ 266
• Four-Wheel Drive Vehicles ................... 266
257

Towing Without the Ignition Key FobSpecial care must be taken when the vehicle is
towed with the ignition in the LOCK position.
The only approved method of towing without
the ignition key is with a flatbed truck. Proper
towing equipment is necessary to prevent
damage to the vehicle.Four-Wheel Drive VehiclesThe manufacturer recommends towing with all
wheelsOFFthe ground. Acceptable methods
are to tow the vehicle on a flatbed or with one
end of vehicle raised and the opposite end on
a towing dolly.
If flatbed equipment is not available, and the
transfer case is operable, the vehicle may be
towed (in the forward direction, with ALL
wheels on the ground), IFthe transfer case is in
NEUTRAL and the transmission is in PARK.
Refer to “Recreational Towing” in “Starting and
Operating” for further information.CAUTION!
• Front or rear wheel lifts should not be used.
Internal damage to the transmission or
transfer case will occur if a front or rear
wheel lift is used when towing.
• Failure to follow these towing methods
could result in damage to the transmission
and/or transfer case. Such damage is not
covered by the New Vehicle Limited War-
ranty.
266