4
J A G U A R X JJ A G U A R X J J A G U A R X J
Comfort adjustments
Driver’s seat
Set the seat position using the following controls.
1\bSeat forwards and back, cushion height and
cushion angle.
\f\b Cushion length.
3\b Side support \b inflate.
4\b Side support \b deflate.
5\b Lumbar support.
6\b Seat back angle and head restraint.
Steering column
7\b With the vehicle stationary, adjust the steering
column to your ideal driving position.
Door mirrors
1\b Press the left or right mirror selector.
\f\b Use the mirror adjuster to set mirror position.
Storing the driving position to memory
Once you have adjusted the driver's seat, steering
column and door mirrors for your ideal driving
position, the settings can be stored.
1\b Press the Mbutton to activate the memory store
function. The button will illuminate to indicate
the memory store function is active.
\f\b Press button 1,\for 3to store the current driving
position to the chosen number.
Use a stored memory position by pressing the
appropriate button; 1,\for 3. The seat, steering wheel
and mirrors will move to their preset positions.
1
2
3456
7
A warning indicator on the instrument panel
will illuminate if the seat belt of an occupied
front seat is unbuckled. This may be
accompanied by an audible warning.
Using child seats
Refer to Child Seat Positioning in the Owner’s
Handbook to determine the correct seat for your
child.
If it becomes necessary to fit a child restraint on the
front passenger seat, make the following seat
adjustments.
• Move the seat fully rearward.
• Lumbar support to minimum setting.
• Seat cushion to highest position.• Cushion front tilt to lowest position.
• Seat back to upright position.
• Adjust the upper seat belt anchorage to its lowest position.
When a front passenger seat occupancy sensor is
fitted it determines the state of seat occupancy and
sets the airbag status to suit. The status indicator is in
the overhead console.
• Seat unoccupied \b airbag deactivated and indicator off.
• Seat occupied \b airbag activated and indicator off.
• Low weight occupant or object \b airbag deactivated and indicator on.
Operating note
Memory buttons 1,\for 3must be pressed within
five seconds after pressing the Mbutton otherwise
the memory store function will cancel.
Setting the driving positionSee page 3, items 28, 37and38
Restraints
JJM 18 96 34 111:X351 10MY.qxd 05/07/2010 15:04 Page 4
6
J A G U A R X JJ A G U A R X J J A G U A R X J
Starting and driving
Electric park brake is
applied. Flashing \b EPB
fault. USA only
Electric park brake is
applied. Flashing \b EPB
fault.
Dynamic stability control
fault. Flashes when DSC is
operating
DSC switched off,
Trac DSC on
Airbag faultLow tire pressure
Seat belt reminder
Automatic speed limiter
active
Forward alert active
Adaptive cruise control
active
Braking system fault or
brake fluid low. USA only
Braking system fault or
brake fluid low.
Anti\block braking system
fault. USA only
Anti\block braking system
fault
Engine malfunction
Gearshift interlock
Apply the footbrake then move the selector from the
Park position. Maintain brake pressure until a gear is
selected.
Automatic gear selection
Select Dfor fully automatic gear changes.
Sport mode
This is an automatic gear change mode, however,
change points are modified to make full use of engine
power.
Press the selector down and rotate from Dto Sport.
Manual gear changes
Manual gear change mode is effective when rapid
acceleration and engine braking are required.
• To shift down, briefly pull the left (\b) paddle.
• To shift up, briefly pull the right (+) paddle.
When the paddles are used in D,gear selection will
revert to automatic if use of the paddles is not
maintained. With Sselected, continuous manual
operation is initiated if the paddles are used.
Select Pbefore switching off the engine. However, if
the engine is switched off with Reverse,Drive or
Sport selected, the selector will automatically return
to Pwhile retracting.
Applying
• With the vehicle stationary, lift up the parking brake lever and then release it. The red warning
lamp in the instrument panel will illuminate.Releasing
• With the ignition on, apply the foot brake and press down on the parking brake lever.
• If the vehicle is stationary with the parking brake applied and either Drive orReverse selected,
pressing the accelerator will automatically release
the parking brake.
Electric parking brakeSee page 3, item 1\b
Operating note
If the engine is switched off with Neutral selected,
automatic selection of Pis delayed for \f0 minutes.
DO NOT use this feature to enable towing of the
vehicle. Refer to Vehicle recovery in the Owner’s
Handbook.
To return to automatic operation pull and hold
the right hand paddle for two seconds.
TransmissionSee page 3, items 2, 4and18
Warning lamps\bisplayed on the instrument panel
JJM 18 96 34 111:X351 10MY.qxd 05/07/2010 15:04 Page 6
