2011 INFINITI QX towing

●Disconnect and secure the center seat belt
and tongues into the retractor base. See
“Stowing 3rd row center seat belt” later in
this section.
– Always reconnect the center seat belt when the seat is returned to the upright
position
● Make sure that there are no objects on the
seatback cushion.
Power reclining
Push and hold the rear side of the switch1
beside the 3rd row cup holders until the desired
seatback angle (up to 20 degrees) is obtained.
To move the seatback forward again, push and
hold the front side of the switch
2until the
desired angle is obtained.
WARNING
● After adjustment, check to be sure the seat is
securely locked.
● Do not ride in a moving vehicle when the
seatback is reclined. This can be dangerous.
The shoulder belt will not be against your
body. In an accident, you could be thrown
into it and receive neck or other serious inju-
ries. You could also slide under the lap belt
and receive serious internal injuries.
● For the most effective protection when the
vehicle is in motion, the seat should be up-
right. Always sit well back in the seat with
both feet on the floor and adjust the seat belt
properly. See “PRECAUTIONS ON SEAT BELT
USAGE” later in this section.
SSS1095
Safety — Seats, seat belts and supplemental restraint system1-7

CAUTION
When folding the 2nd row seat for maximum
cargo hauling, be sure that cargo does not con-
tact the center console of the captain’s seat (if
so equipped) to avoid possible damage to the
console.
Stowing 2nd and 3rd row seats
To stow 2nd and 3rd row seats for maximum
cargo capacity:
Manual Operation:
1. Pull lever A or B located on the 2nd rowseat. The seatback folds down and the
seat base will tip forward. See “Entry to
3rd row seat” earlier in this section.
Power Operation:
1. Push and hold the corresponding switchlocated on the instrument panel below the
audio system. The seatback will fold down
and tip forward. See “Entry to 3rd row
seat” earlier in this section. 2. Push the folded seat down until it locks in
position. 3. Fold the 3rd row seat flat using the
switches located in the cargo area. See
“Power folding” earlier in this section.
4. Return 3rd row seats to seating positions by raising the 3rd row seatbacks to an
upright position using the switches. Make
sure the seatback is locked in position.
See “Power folding” earlier in this sec-
tion.
5. Return the 2nd row seat to a seating position by raising the 2nd row seatbacks
to an upright position. Make sure the
seatback is locked in position.
SSS1120SSS1121
Safety — Seats, seat belts and supplemental restraint system1-17

WARNING
●Always fasten the connector tongue and the
seat belt in the order shown.
● Always make sure both the connector
tongue and the seat belt tongue are secured
when using the seat belt or installing a child
restraint. Do not use the seat belt or child
restraint with only the seat belt tongue at-
tached. This could result in serious personal
injury in case of an accident or a sudden
stop. Stowing 3rd row center seat belt :
When folding down the 3rd row seat, the 3rd
center seat belt can be retracted into a stowed
position.
1. Hold the connector tongue1so that the
seat belt does not retract suddenly when
the tongue is released from the connector
buckle. Release the connector tongue by
inserting a suitable tool such as key
A
into the connector buckle.
2. Store the seat belt tongue into the tongue holder
Bfirst2.
3. Store the connector tongue into the re- tractor base
3.
WARNING
Do not unfasten the 3rd center seat belt con-
nector except when folding down the 3rd seat.
SSS0241
SSS1077
Safety — Seats, seat belts and supplemental restraint system1-25

●Always use tires of the same type, size,
brand, construction (bias, bias-belted or ra-
dial), and tread pattern on all four wheels.
Install tire chains on the rear wheels when
driving on slippery roads and drive carefully.
● Be sure to check the brakes immediately af-
ter driving in mud or water. See “BRAKE SYS-
TEM” later in this section for wet brakes.
● Avoid parking your vehicle on steep hills. If
you get out of the vehicle and it rolls forward,
backward or sideways, you could be injured.
● Whenever you drive off-road through sand,
mud or water as deep as the wheel hub, more
frequent maintenance may be required. See
the maintenance information in the “INFINITI
Service and Maintenance Guide”.
● Spinning the rear wheels on slippery sur-
faces may cause the 4WD warning light to
flash. The 4WD system may also automati-
cally switch from the 4WD mode to the 2WD
mode. This could reduce traction. Be espe-
cially careful when towing a trailer (4WD
models).WARNING
Do not operate the push-button ignition switch
while driving the vehicle except in an emer-
gency. (The engine will stop when the ignition
switch is pushed 3 consecutive times or the
ignition switch is pushed and held for more
than 2 seconds.) If the engine stops while the
vehicle is being driven, this could lead to a
crash and serious injury.
Before operating the push-button ignition
switch, be sure to move the selector lever to the
P (Park) position.
OPERATING RANGE FOR ENGINE
START FUNCTION
The operating range for starting the engine
inside the vehicle
1is shown in the illustra-
tion.
● If the Intelligent Key is on the instrument
panel, cargo area, inside the glove box or
door pocket, or the corner of interior com-
partment, it may not be possible to start the
engine.
● If the Intelligent Key is near the door or door
glass outside the vehicle, it may be possible
to start the engine.
SSD0436
PUSH-BUTTON IGNITION SWITCH
5-10Starting and driving

5. To stop the engine, shift the selector leverto the P (Park) position and push the
ignition switch to the OFF position.ENGINE PROTECTION MODE
The engine has an engine protection mode to
reduce the chance of damage if the coolant
temperature becomes too high (for example,
when climbing steep grades in high tempera-
ture with heavy loads, such as when towing a
trailer).
When the engine temperature reaches a certain
level:
● The engine coolant temperature gauge will
move toward the H position.
● Engine power may be reduced.
● The air conditioning cooling function may be
automatically turned OFF for a short time
(the blower will continue to operate).
Engine power and, under some conditions, ve-
hicle speed will decrease. Vehicle speed can be
controlled with the accelerator pedal, but the
vehicle may not accelerate at the desired
speed. The transmission will downshift or up-
shift as it reaches prescribed shift points. You
can also shift manually.
As driving conditions change and engine cool-
ant temperature is reduced, vehicle speed can
be increased using the accelerator pedal, and
air conditioning cooling function will automati-
cally be turned back ON. If:1. The engine coolant temperature is not
reduced.
2. The air conditioning cooling function does not turn back ON.
3. The engine oil pressure warning light
illuminates or engine coolant tem-
perature gauge does not return to the
normal range from the H position, this
may indicate a malfunction. Move the
vehicle off the road to a safe area and
allow the engine to cool. If after checking
the oil and coolant, the
remains on
or engine coolant temperature does not
return to the normal range, do not con-
tinue to drive and contact an INFINITI
retailer.
The Malfunction Indicator Light (MIL)may also come ON. You do not need to have
your vehicle towed, unless it remains on, but
have it inspected soon by an INFINITI retailer.
See “WARNING/INDICATOR LIGHTS AND AU-
DIBLE REMINDERS” in the “2. Instruments and
controls” section.
DRIVING THE VEHICLE
5-14Starting and driving

LANE DEPARTURE PREVENTION (LDP)
SYSTEM
Precautions on LDP system
WARNING
●The LDP system will not steer the vehicle or
prevent loss of control. It is the driver’s re-
sponsibility to stay alert, drive safely, keep
the vehicle in the traveling lane, and be in
control of vehicle at all times.
● The LDP system is primarily intended for use
on well-developed freeways or highways. It
may not detect the lane markers in certain
roads, weather or driving conditions.
● Using the LDP system under some condi-
tions of road, lane marker or weather, or
when you change lanes without using the
lane change signal could lead to an unex-
pected system operation. In such condi-
tions, you need to correct the vehicle’s direc-
tion with your steering operation to avoid
accidents.
● When the LDP system is operating, avoid
excessive or sudden steering maneuvers.
Otherwise, you could lose control of the
vehicle. ●
The LDP system will not operate at speeds
below approximately 45 MPH (70 km/h) or if
it cannot detect lane markers.
● The LDP system may not function properly
under the following conditions, and do not
use the LDP system:
– During bad weather (rain, fog, snow, wind, etc.).
– When driving on slippery roads, such as on ice or snow, etc.
– When driving off-road such as on sand or rock, etc.
– When driving on winding or uneven roads.
– When there is a lane closure due to road repairs.
– When driving in a makeshift lane.
– When driving on roads where the lane width is too narrow.
– When driving without normal tire condi- tions (for example, tire wear, low tire
pressure, installation of spare tire, tire
chains, non-standard wheels).
– When the vehicle is equipped with non- original brake parts or suspension parts.
– When towing a trailer or other vehicle. ●
If the LDP system malfunctions, it will cancel
automatically. The lane departure warning
light (orange) on the instrument panel will
illuminate.
● If the lane departure warning light (orange)
illuminates, pull off the road to a safe loca-
tion and stop the vehicle. Turn the engine off
and restart the engine. If the warning light
(orange) continues to illuminate, have the
LDP system checked by an INFINITI retailer.
● Excessive noise will interfere with the warn-
ing chime sound, and the chime may not be
heard.
The functions of the LDP system (warning and
brake control assist) may or may not operate
properly under the following conditions:
● On roads where there are multiple parallel
lane markers; lane markers that are faded or
not painted clearly; yellow painted lane
markers; non-standard lane markers; or lane
markers covered with water, dirt, snow, etc.
● On roads where discontinued lane markers
are still detectable.
5-24Starting and driving

How to enable/disable the BSW system using
the settings menu :
Perform the following steps to enable or disable
the BSW system.
1. Push the SETTING1button and highlight
the “Driver Assistance” key on the display
using the INFINITI controller. Then push
the ENTER
2button.
2. Highlight the “Driver Assistance Warn- ings” key, and push the ENTER
2button.
3. Highlight the “Blind Spot Warning” key,select ON (enabled) or OFF (disabled) and
push the ENTER
2button.
BSW system precautions
WARNING
●Do not use the BSW system when towing a
trailer because the system may not function
properly.
● Excessive noise (e.g. audio system volume,
open vehicle window) will interfere with the
chime sound, and it may not be heard.
SSD0959
SSD1102
JVS0080X
5-32Starting and driving

WARNING
●As there is a performance limit to the dis-
tance control function, never rely solely on
the Intelligent Cruise Control (ICC) system.
This system does not correct careless, inat-
tentive or absent-minded driving, or over-
come poor visibility in rain, fog, or other bad
weather. Decelerate the vehicle speed by de-
pressing the brake pedal, depending on the
distance to the vehicle ahead and the sur-
rounding circumstances in order to maintain
a safe distance between vehicles.
● If the vehicle ahead comes to a stop, the
vehicle decelerates to a standstill within the
limitations of the system. The system will
cancel once it judges that the vehicle has
come to a standstill and sound a warning
chime. To prevent the vehicle from moving,
the driver must depress the brake pedal.
● The system may not function properly under
the following conditions. To avoid accidents,
never use the ICC system under the following
conditions:
– On roads where the traffic is heavy or there are sharp curves
– On slippery road surfaces such as on ice or snow, etc. – On off-road surfaces such as on sand or
rock, etc.
– During bad weather (rain, fog, snow, etc.)
– When the windshield wipers are operat- ing at high speed. The system may cancel
when the wipers are set to the AUTO
position.
– When strong light (for example, at sun- rise or sunset) is directly shining on the
front of the vehicle
– When rain, snow or dirt adhere to the sys- tem sensor
– On steep downhill roads (the vehicle may go beyond the set vehicle speed and fre-
quent braking may result in overheating
the brakes)
– On repeated uphill and downhill roads
– When traffic conditions make it difficult to keep a proper distance between vehicles
because of frequent acceleration or
deceleration
– When towing a trailer or other vehicle ●
In some road or traffic conditions, a vehicle
or object can unexpectedly come into the
sensor detection zone and cause automatic
braking. You may need to control the dis-
tance from other vehicles using the accelera-
tor pedal. Always stay alert and avoid using
the ICC system when it is not recommended
in this section.
5-42Starting and driving