2011 INFINITI QX fuel consumption

TRIP COMPUTER
Switches for the trip computer are located on
the right side of the combination meter panel.
To operate the trip computer, push the switches
as shown above.
Aswitch
Bswitch
When the ignition switch is pushed to the ON
position, modes of the trip computer can be
selected by pushing the
switchA. Each time the
switchAis pushed, the
display will change as follows:
Current fuel consumption →Average fuel con-
sumption and speed →Elapsed time and trip
odometer →Distance to empty (dte) →Outside
air temperature (ICY) →Setting →Warning
check
1. Current and average fuel
consumption
The current and average fuel consumption
mode shows the current and average fuel con-
sumption.
2. Average fuel consumption (MPG or
l (liter)/100 km) and speed (MPH or
km/h)
Fuel consumption :
The average fuel consumption mode shows the
average fuel consumption since the last reset.
Resetting is done by pushing the
switch
Bfor longer than 1 second. (The average speed
is also reset at the same time.)
The display is updated every 30 seconds. At
about the first 1/3 mile (500 m) after a reset, the
display shows “——”. Speed :
The average speed mode shows the average
vehicle speed since the last reset. Resetting is
done by pushing the
switchBfor longer
than 1 second. (The average fuel consumption is
also reset at the same time.)
The display is updated every 30 seconds. The
first 30 seconds after a reset, the display shows
“——”.
3. Elapsed time and trip odometer
(MILES or km)
Elapsed time :
The elapsed time mode shows the time since
the last reset. The displayed time can be reset
by pushing the
switchBfor longer than
1 second. (The trip odometer is also reset at the
same time.)
Trip odometer :
The trip odometer mode shows the total dis-
tance the vehicle has been driven since the last
reset. Resetting is done by pushing the
switchBfor longer than 1 second. (The
elapsed time is also reset at the same time.)
SIC4420
Instruments and controls2-27

2. Menu Selections:
Shows the options to choose within that
menu screen.
3. UP/DOWN Movement indicator:
Shows that the INFINITI controller may be
used to move UP/DOWN on the screen and
select more options.
4. Menu Items Counter:
Shows the total number of items listed
across all pages for the current menu.
5. Footer/Information Line:
Provides more information (if available)
about the menu selection currently high-
lighted.
HOW TO USE STATUS BUTTON
To display the status of the audio, air condi-
tioner system, fuel consumption and navigation
system, push the STATUS button. The following
information will appear when the STATUS but-
ton is pushed repeatedly.
Audio and Air conditioner system→Audio and
fuel economy →Audio and Navigation system
HOW TO USE BRIGHTNESS CONTROL
AND DISPLAY ON/OFF BUTTON
Push the “OFF” button to switch the
display brightness to the daytime mode or the
nighttime mode, and to adjust the display
brightness using the INFINITI controller while
the indicator is displayed at the bottom of the
screen.
Push and hold the “
OFF” button for more
than 2 seconds to turn the display off. Push the
button again to turn the display on.
HOW TO USE INFO BUTTON
The display screen shows vehicle and naviga-
tion information for your convenience.
The information shown on the screen should be
a guide to determine the condition of the ve-
hicle. See the following for details.
VEHICLE INFORMATION AND SETTINGS
Monitor, climate, audio, phone and voice recognition systems4-7

Fuel Economy information
The distance to empty, average fuel economy
and current fuel economy will be displayed for
reference.
To reset the average fuel economy (Avg Fuel
Econ), select the “Reset Fuel Eco” key.
If the “Fuel Eco History” key is selected, the
average fuel consumption history will be dis-
played in graph form along with the average for
the previous Reset-to-Reset period.
The unit can be converted between “US” and
“Metric”. (See “HOW TO USE SETTING BUTTON”
later in this section.)
The fuel economy information may differ from
the information displayed on the vehicle infor-
mation display. This is due to the timing differ-
ence in updating the information and does not
indicate a malfunction.
TIRE PRESSURE information
WARNING
●When a spare tire is mounted or a wheel is
replaced, tire pressure will not be indicated,
the TPMS will not function and the low tire
pressure warning light will flash for approxi-
mately 1 minute. The light will remain on
after 1 minute. Contact your INFINITI retailer
as soon as possible for tire replacement
and/or system resetting. ●
Replacing tires with those not originally
specified by INFINITI could affect the proper
operation of the TPMS.
The tire pressure will be displayed for refer-
ence.
The pressure indication “** kPa” or “** psi” on
the screen means that the pressure is being
measured. After a few driving trips, the pres-
sure for each tire will be displayed.
To change the measurement units, select the
“Select Units” key with the INFINITI controller
and push the ENTER button.
In case of low tire pressure, LOW PRESSURE
information will be displayed on the screen.
Check the pressure of all tires.
Tire pressure rises and falls depending on the
heat caused by the vehicle’s traveling condition
and the temperature.
After tire rotation is performed, tire pressure
will not be displayed in the actual tire position.
Drive the vehicle at over 25 MPH (40 km/h) for
approximately 10 minutes to reset the display.
SAA3146
Monitor, climate, audio, phone and voice recognition systems4-9

WARNING
●Do not attempt to raise two wheels off the
ground and shift the transmission to any
drive or reverse position with the engine run-
ning. Doing so may result in drivetrain dam-
age or unexpected vehicle movement which
could result in serious vehicle damage or
personal injury.
● Do not attempt to test a 4WD equipped ve-
hicle on a 2-wheel dynamometer or similar
equipment even if the other two wheels are
raised off the ground. Make sure you inform
test facility personnel that your vehicle is
equipped with 4WD before it is placed on a
dynamometer. Using the wrong test equip-
ment may result in drivetrain damage or un-
expected vehicle movement which could re-
sult in serious vehicle damage or personal
injury.
CAUTION
● Do not drive the vehicle in the 4HI or 4LO
position on dry hard surface roads. Driving
on dry, hard surfaces in 4HI or 4LO may
cause unnecessary noise, tire wear and in-
creased fuel consumption.
If the Four-Wheel Drive (4WD) warning light
turns on when driving on dry hard surface
roads:
– in the 4HI position, shift the 4WD shift switch to AUTO.
– in the 4LO position, stop the vehicle and shift the transmission lever to the N (Neu-
tral) position with the brake pedal de-
pressed and shift the 4WD shift switch to
AUTO.
If the 4WD warning light is still on after
the above operation, have your vehicle
checked by an INFINITI retailer as soon as
possible.
● The transfer case may be damaged if you
continue driving with the 4WD warning light
blinking.
See “ON-PAVEMENT AND OFF-ROAD DRIVING
PRECAUTIONS” earlier in this section for other
precautions for offroad driving.
INFINITI ALL-MODE 4WD SYSTEM
The all mode 4WD system provides 3 positions
(AUTO, 4HI and 4LO), so you can select the
desired drive mode according to the driving
conditions.
INFINITI ALL-MODE 4WD(if so equipped)
5-84Starting and driving

The 4WD shift switch is used to select the 4WD
mode depending on the driving conditions.
There are 3 types of drive modes available,
AUTO, 4HI and 4LO.
The 4WD shift switch electronically controls the
transfer case operation. Rotate the switch to
move between each mode, AUTO, 4H and 4L.
You must depress the 4WD shift switch to select
4L, and the vehicle MUST be stationary and the
selector lever in the N (Neutral) position when
changing into or out of 4L.
WARNING
●When parking, apply the parking brake be-
fore stopping the engine and make sure that
the 4WD shift indicator is on and the ATP
warning light turns off. Otherwise, the ve-
hicle could unexpectedly move even if the
automatic transmission is in the P (Park)
position.
● The 4LO and 4HI indicators must stop blink-
ing and the 4LO or 4HI indicator must remain
illuminated or turn off before shifting the
transmission into gear. If the selector lever
is shifted from the N (Neutral) position to any
other gear while the 4LO and 4HI indicators
are blinking alternately, the vehicle may
move unexpectedly.
CAUTION
● Never shift the 4WD shift switch between 4L
and 4H while driving.
● The 4HI position provides greater traction.
Avoid excessive speed, as it will cause in-
creased fuel consumption and higher oil
temperatures, and could damage drivetrain
component. Speeds over 62 MPH (100 km/h)
in 4HI is not recommended.
● The 4LO position provides maximum trac-
tion. Avoid raising vehicle speed exces-
sively, as the maximum speed is approxi-
mately 31 MPH (50 km/h).
● When driving straight, shift the 4WD shift
switch to the AUTO or 4H position. Do not
move the 4WD shift switch when making a
turn or reversing.
● Do not shift the 4WD shift switch (between
AUTO and 4H) while driving on steep down-
hill grades. Use the engine brake and low
automatic transmission gears for engine
braking.
● Do not operate the 4WD shift switch (be-
tween AUTO and 4H) with the rear wheels
spinning. ●
Do not drive on dry hard surface roads in the
4HI or 4LO position. Driving on dry hard sur-
faces in 4HI or 4LO may cause unnecessary
noise and tire wear. INFINITI recommends
driving in the AUTO position under these
conditions.
● The 4WD transfer case may not be shifted
between 4HI and 4LO at low ambient tem-
peratures and the 4LO and 4HI indicators
may blink even when the 4WD shift switch is
shifted. After driving for a while you can
change the 4WD shift switch between 4H
and 4L.
When driving on rough roads,
● Drive carefully according to the road surface
conditions.
When the vehicle is stuck,
● Place stones or wooden blocks under the
tires to free the vehicle.
● Set the 4WD shift switch to 4H or 4L.
● If it is difficult to free the vehicle, repeat
forward and backward movement to increase
the movement.
● If the vehicle is stuck deep in mud, tire
chains may be effective.
Starting and driving5-87

The 4WD warning light comes on when the
ignition switch is placed in the ON position. It
turns off soon after the engine is started.
If any malfunction occurs in the 4WD system
when the ignition switch is placed in the ON
position, the 4WD warning light will either
remain illuminated or blink.
If the 4WD warning light comes on, the 4WD
shift indicator turns off.
High-temperature transfer case oil makes the
4WD warning light blink rapidly (about twice per
second). If the warning light blinks rapidly
during operation, stop the vehicle in a safe
place immediately. Then if the light turns off
after a while, you can continue driving.
A large difference between the diameters of
front and rear wheels will make the 4WD warn-
ing light blink slowly (about once per two
seconds). Change the 4WD shift switch to AUTO
and do not drive fast.CAUTION
●If the 4WD warning light comes on or blinks
slowly during operation or rapidly after stop-
ping the vehicle for a while, have your ve-
hicle checked by an INFINITI retailer as soon
as possible.
● Shifting between 4HI and 4LO is not recom-
mended when the 4WD warning light turns
on.
● When the 4WD warning light comes on, the
2WD mode may be engaged even if the 4WD
shift switch is in AUTO or 4H. Be especially
careful when driving. If corresponding parts
are malfunctioning, the 4WD mode will not
be engaged even if the 4WD shift switch is
shifted.
● Do not drive the vehicle in the 4HI or 4LO
position on dry hard surface roads. Driving
on dry, hard surfaces in 4HI or 4LO may
cause unnecessary noise, tire wear and in-
creased fuel consumption.
If the 4WD warning light turns on when driv-
ing on dry hard surface roads:
– in the AUTO or 4HI position, shift the 4WD shift switch to AUTO. – in the 4LO position, stop the vehicle and
shift the transmission selector lever to
the N (Neutral) position and shift the 4WD
shift switch to AUTO.
● If the 4WD warning light is still on after the
above operation, have your vehicle checked
by an INFINITI retailer as soon as possible.
● The transfer case may be damaged if you
continue driving with the warning light
blinking.
5-90Starting and driving

E-85 fuel
E-85 fuel is a mixture of approximately 85% fuel
ethanol and 15% unleaded gasoline. E-85 can
only be used in a Flexible Fuel Vehicle (FFV). Do
not use E-85 fuel in your vehicle. U.S. govern-
ment regulations require fuel ethanol dispens-
ing pumps to be identified by a small, square,
orange and black label with the common abbre-
viation or the appropriate percentage for that
region.
Aftermarket fuel additives
INFINITI does not recommend the use of any
aftermarket fuel additives (Example: fuel injec-
tor cleaner, octane booster, intake valve de-
posit removers, etc.) which are sold commer-
cially. Many of these additives intended for
gum, varnish or deposit removal may contain
active solvent or similar ingredients that can be
harmful to the fuel system and engine.
Octane rating tips
Using unleaded gasoline with an octane rating
lower than recommended above can cause per-
sistent, heavy spark knock. (Spark knock is a
metallic rapping noise.) If severe, this can lead
to engine damage. If you detect a persistent
heavy spark knock even when using gasoline of
the stated octane rating, or if you hear steady
spark knock while holding a steady speed on
level roads, have an INFINITI retailer correct the
condition. Failure to correct the condition is mis-
use of the vehicle, for which INFINITI is not re-
sponsible.
Incorrect ignition timing will result in knocking,
after-run or overheating. This in turn may cause
excessive fuel consumption or damage to the
engine. If any of the above symptoms are
encountered, have your vehicle checked at an
INFINITI retailer or other competent service fa-
cility.
However, now and then you may notice light
spark knock for a short time while accelerating
or driving up hills. This is no cause for concern,
because you get the greatest fuel benefit when
there is light spark knock for a short time under
heavy engine load.
CAUTION
●Your vehicle is not designed to run on E-85
fuel. Using E-85 fuel in a vehicle not specifi-
cally designed for E-85 fuel can damage fuel
system components and is not covered by
the INFINITI new vehicle limited warranty.
● E-85 is a mixture of approximately 85% fuel
ethanol and 15% unleaded gasoline.
● U.S. government regulations require ethanol
dispensing pumps to be identified by a
small, square, orange and black label with
the common abbreviation or the appropriate
percentage for that region.
Technical and consumer information9-5

10 Index
A
ABS (Anti-lock Braking System) .......5-97
Adaptive front lighting system (AFS) ....2-40
Advanced air bag system ...........1-55
Aiming control Adaptive front lighting system (AFS) . . 2-40
Headlights ................. 2-39
Air bag system Advanced air bag system .........1-55
Front passenger air bag and status
light ..................... 1-57
Front-seat mounted side-impact
supplemental air bag system ......1-60
Roof-mounted curtain side-impact and
rollover supplemental air bag system . . 1-60
Air bag warning labels ............1-63
Air bag warning light ..........1-63, 2-16
Air cleaner housing filter ...........8-18
Air conditioner Advanced Climate Control System
(ACCS) ................... 4-35
Air conditioner service ..........4-40
Air conditioner specification label ....9-12
Air conditioning system refrigerant and
lubricant recommendations .....4-40, 9-7
Automatic climate control .....4-31, 4-34
In-cabin microfilter ............4-39
Alarm, How to stop alarm
(see vehicle security system) .........2-31
Alcohol, drugs and driving ...........5-8
Antenna .................... 4-82Anti-lock Braking System (ABS)
.......5-97
Anti-lock braking system (ABS) warning
light ....................... 2-11
Appearance care Exterior appearance care ..........7-2
Interior appearance care ..........7-4
Armrest ..................... 1-16
Around View™ Monitor ............4-19
Audible reminders ............... 2-20
Audio operation precautions .........4-40
Audio system ................. 4-40
Steering wheel audio controls ......4-81
Auto closure .................. 3-23
Autolight system ................ 2-37
Automatic Automatic transmission fluid (ATF) ....8-11
Climate control ........... 4-31,
4-34
Door locks ..................3-5
Drive positioner .............. 3-30
Driving with automatic transmission . . . 5-15
Moonroof .................. 2-64
Seat positioner .............. 3-30
Average fuel consumption and speed ....2-27
Avoiding collision and rollover ........5-6
B
Back door (See lift gate) ...........3-19
Battery ..................... 8-15
Battery saver system ........2-39, 2-66
Intelligent Key ............... 8-24
Variable voltage control system .....8-16 Before starting the engine
..........5-13
Belts (See drive belts) .............8-17
Blind Spot Warning (BSW) system . . . . . . 5-29
Blind Spot Warning (BSW) system warning
light ....................... 2-12
Bluetooth Hands-Free Phone System . . . 4-96
Booster seats ................. 1-47
Brake Anti-lock Braking System (ABS) . ....5-97
Brake booster ............... 8-21
Brake fluid .............. 8-12, 8-13
Brake system ............... 5-94
Parking brake operation .........5-19
Warning light ................ 2-12
Break-in schedule ............... 5-83
Brightness control Display ON/OFF button ...........4-7
Instrument panel .............. 2-41
Bulb check/instrument panel .........2-11
Bulb replacement ............... 8-26
C
Cabin air filter ................. 4-39
Capacities and recommended
fuel/lubricants .................9-2
Car phone or CB radio ............4-95
Cargo floor box ................ 2-60
Cargo light ................... 2-68
Catalytic converter, Three way catalyst ....5-2
CD/CF/USB memory care and cleaning . . . 4-80
Center
multi-function control panel . . ....4-3