2011 INFINITI M fog light

To defog/defrost the rear window glass and
outside mirrors, start the engine and push the
switch
1on. The indicator light2will come
on. Push the switch again to turn the defroster
off.
It will automatically turn off in approximately 30
minutes.
CAUTION
When cleaning the inner side of the rear win-
dow, be careful not to scratch or damage the
rear window defroster.
XENON HEADLIGHTS
WARNING
HIGH VOLTAGE
● When xenon headlights are on, they produce
a high voltage. To prevent an electric shock,
never attempt to modify or disassemble.
Always have your xenon headlights replaced
at an INFINITI retailer.
● Xenon headlights provide considerably more
light than conventional headlights. If they
are not correctly aimed, they might
temporarily blind an oncoming driver or the
driver ahead of you and cause a serious
accident. If headlights are not aimed
correctly, immediately take your vehicle to
an INFINITI retailer and have the headlights
adjusted correctly.
When the xenon headlight is initially turned on,
its brightness or color varies slightly. However,
the color and brightness will soon stabilize. ●
The life of xenon headlights will be shortened
by frequent on-off operation. It is generally
desirable not to turn off the headlights for
short intervals (for example, when the ve-
hicle stops at a traffic signal). Even when the
daytime running lights are active (Canada
only), the xenon headlights do not turn on.
This way the life of the xenon headlights is
not reduced.
● If the xenon headlight bulb is close to burn-
ing out, the brightness will drastically de-
crease, the light will start blinking, or the
color of the light will become reddish. If one
or more of the above signs appear, contact an
INFINITI retailer.
SIC4330
REAR WINDOW AND OUTSIDE MIRROR
DEFROSTER SWITCH HEADLIGHT AND TURN SIGNAL SWITCH
2-32Instruments and controls
—
—
07/15/10—tbrooks


TURN SIGNAL SWITCH
1Turn signal
Move the lever up or down to signal the turning
direction. When the turn is completed, the turn
signals cancel automatically.
2Lane change signal
To indicate a lane change, move the lever up or
down to the point where lights begin flashing.
FOG LIGHT SWITCH
To turn the fog lights on, turn the headlight
switch to the
position, then turn the
switch to the
position. To turn them off,
turn the switch to the OFF position.
The headlights must be on for the fog lights to
operate.
When the headlight switch is in the AUTO
position, turning the fog light switch to the
position will turn on the headlights, fog
lights and the other lights while the ignition
switch is in the ON position or the engine is
running. Push the switch on to warn other drivers when
you must stop or park under emergency condi-
tions. All turn signal lights will flash.
WARNING
●
If stopping for an emergency, be sure to
move the vehicle well off the road.
● Do not use the hazard warning flashers while
moving on the highway unless unusual cir-
cumstances force you to drive so slowly that
your vehicle might become a hazard to other
traffic.
● Turn signals do not work when the hazard
warning flasher lights are on.
SIC3271SIC3272SIC2574
HAZARD WARNING FLASHER SWITCH
Instruments and controls2-37
—
—
07/15/10—tbrooks


2. Push the temperature control button(driver side) to set the desired tempera-
ture.
●The temperature can be set within the
following range.
– For U.S.: 60 to 90°F (16 to 32°C)
– For Canada: 64 to 90°F (18 to 32°C)
● The temperature of the passenger com-
partment will be maintained automati-
cally. Air flow distribution and fan speed
will also be controlled automatically.
3. To turn off the climate control system, push the “OFF” button.
A visible mist may be seen coming from the
ventilators in hot, humid conditions as the air is
cooled rapidly. This does not indicate a mal-
function.
Dehumidified defrosting or defogging:
1. Push the front defroster “” button.
(The indicator light on the button will
come on.)
2. Push the temperature control button to set the desired temperature.
●To quickly remove ice from the outside of the
windows, push the fan speed increase
“
” button and set it to the maximum
position. ●
As soon as possible after the windshield is
clean, push the “AUTO” button to return to
the auto mode.
● When the front defroster “
” button is
pushed, the air conditioner will automati-
cally be turned on at outside temperatures
above 23°F (5°C) to defog the windshield,
and the air recirculate mode will automati-
cally be turned off.
Outside air is drawn into the passenger
compartment to improve the defogging per-
formance.
Manual operation
Fan speed control :
Push the fan speed increase “
”or
decrease “
” buttons to manually control
the fan speed.
Push the “AUTO” button to return to automatic
control of the fan speed. Air recirculation :
Push the air recirculation “
” button to
change the air circulation mode. When the
indicator light illuminates, the flowing air is
recirculated inside the vehicle.
The air recirculation mode cannot be activated
when the air conditioner is in the front defrost-
ing mode “
”.
Outside air circulation :
Push the outside air circulation “
” button
to change the air circulation mode. When the
indicator light illuminates, the flowing air is
drawn from outside the vehicle.
Automatic air intake control :
To set the automatic control mode, perform one
of the following operations.
● When the outside air circulation mode is on,
push and hold the outside air circulation
“
” button for more than 2 seconds.
● When the air recirculation mode is on, push
and hold the air recirculation “
” but-
ton for more than 2 seconds.
When setting the automatic control mode, both
indicator lights will blink twice indicating that
the system is in the automatic control mode.
Monitor, climate, audio, phone and voice recognition systems4-33
—
—
01/12/10—pattie


1. “” front defroster button
2. “
” rear window defogger button
(See “REAR WINDOW AND OUTSIDE
MIRROR DEFROSTER SWITCH” in the
“2. Instruments and controls” section.) 3. “OFF” button for climate control system
4. “” fan speed decrease button
5. “
” fan speed increase button
6. “AUTO” automatic operation button 7. “
” Forest button
8. “
” intake air control button
9. “CLIMATE” button
10, 11. Temperature control button (driver side)
12. “
” manual air flow control button
(driver side)
13. “
” manual air flow control button
(passenger side)
14, 15. Temperature control button (passen- ger side)
AUTOMATIC CLIMATE CONTROL
(Type B)
Automatic operation
Cooling and/or dehumidified heating (AUTO) :
This mode may be used year-round as the
system automatically controls constant tem-
perature, air flow distribution and fan speed
after the desired temperature is set manually.
1. Push the “AUTO” button.(The AUTO indicator light on the button
will illuminate and “AUTO” will appear on
the display.)
Type B
SAA2951
4-36Monitor, climate, audio, phone and voice recognition systems
—
—
01/13/10—tbrooks


2. Push the temperature control button (driv-er’s side) to set the desired temperature.
●The temperature can be set within the
following range.
– For U.S.: 60 to 90°F (16 to 32°C)
– For Canada: 64 to 90°F (18 to 32°C)
● The temperature of the passenger com-
partment will be maintained automati-
cally. Air flow distribution and fan speed
will also be controlled automatically.
3. To turn off the climate control system, push the “OFF” button.
A visible mist may be seen coming from the
ventilators in hot, humid conditions as the air is
cooled rapidly. This does not indicate a mal-
function.
Dehumidified defrosting/defogging:
1. Push the “” button. (The indicator
light will illuminate.)
2. Push the temperature control button to set the desired temperature.
●To remove frost from the outside surface
of the windshield quickly, set the tem-
perature control and fan speed control to
their maximum position. ●
After the windshield is cleared, push the
“AUTO” button to set to the automatic
mode.
● When the “
” button is pushed, the
air conditioner will automatically turn on
when the outside air temperature is
above 23°F (5°C) to defog the wind-
shield. The air recirculation mode will
automatically turn off. The outside air
circulation mode will be selected to im-
prove the defogging performance.
Manual operation
The manual mode can be used to control the
heater and air conditioner to your desired set-
tings.
To turn off the heater and air conditioner, push
the “OFF” button.
Fan speed control :
Push the fan speed control “
” button to
increase the fan speed.
Push the fan speed control “
” button to
decrease the fan speed.
Push the “AUTO” button to change the fan
speed to the automatic mode. Air flow control :
Push the “
” button to change the air flow
mode.
: Air flows from the center and side ventilators.
: Air flows from the center and sideventilators, and foot outlets.
: Air flows mainly from the foot outlets.
: Air flows from the defogger and footoutlets.
Temperature control :
Turn the temperature control dial to set the
desired temperature.
● The temperature can be set within the fol-
lowing range.
– For U.S.: 60 to 90°F (16 to 32°C)
– For Canada: 64 to 90°F (18 to 32°C)
Air recirculation :
Push the intake air control “
” button to
recirculate interior air inside the vehicle. The
“
” indicator light on the button will come
on.
Monitor, climate, audio, phone and voice recognition systems4-37
—
—
01/13/10—tbrooks


The air recirculation mode cannot be activated
when the air conditioner is in the front defrost-
ing mode “
”.
Outside air circulation :
Push the intake air control “
” button to
change the air circulation from the intake air to
the outside air. The “
” indicator light will
turn off.
Automatic air intake control :
In the AUTO mode, the intake air will be con-
trolled automatically. To manually control the
intake air, push the intake air control “
”
button. To return to the automatic control mode,
push the intake air control “
” button for
approximately 2 seconds. The indicator lights
will flash twice, and then the intake air will be
controlled automatically.
CLIMATE setting screen
Climate control settings can be changed on the
screen.
Push the “CLIMATE” button on the instrument
panel and turn the display to the “Climate”
screen.
Heating (A/C off) :
The air conditioner does not activate in this
mode. When you need to heat only, use this
mode.
1. Push the “CLIMATE” button to on.
2. Push the “AUTO” button. (The “AUTO”
indicator on the screen will illuminate and
“AUTO” will appear on the display.) 3. If the “A/C” indicator illuminates, select
the “A/C” key. (The “A/C” indicator will
turn off.)
4. Push the temperature control button to set the desired temperature.
●Do not set the temperature lower than the
outside air temperature. Doing so may cause
the temperature to not to be controlled
properly.
● If the windows fog up, use dehumidified
heating instead of A/C off heating.
Dual control mode setting :
You can individually set driver and front pas-
senger side temperature and air flow mode
using each temperature control or manual air
flow control button.
1. Push the “CLIMATE” button to on.
2. By selecting the “DUAL” key, or when the passenger side temperature control but-
ton or manual air control button is
pushed, the “DUAL” indicator on the
screen will illuminate.
3. To turn off the passenger side tempera- ture control, select the “DUAL” key and
the “DUAL” indicator will turn off.
SAA2959
4-38Monitor, climate, audio, phone and voice recognition systems
—
—
01/12/10—pattie


indicator light on thebutton illumi-
nates when the system is operating.
● The air flow control is not available in the
front defogger mode. When the “
”
button is pushed while the Forest Air™
system is turned on, the Forest Air™ system
will turn off.
Operating tips
Breeze Mode :
When this mode is ON, fan speed fluctuates
during the Forest Air™ system operation, creat-
ing a wind breeze similar to a natural breeze
using a combination of the upper ventilator and
the center ventilators at random.
● Breeze Mode will activate after the tempera-
ture of the passenger compartment becomes
suitable.
● This function will not operate immediately
after the engine starts.
● Breeze Mode is activated when the air flow
mode is in the 
and mode.
● This function will turn off if the fan speed or
a ventilator outlet is manually adjusted.
● The breeze patterns may change in accor-
dance with the amount of sun load. ●
When operating fan speed or air flow control
while the Forest Air™ system is turned on,
the “
” indicator light on the button will
turn off automatically, and the Breeze Mode
function will turn off.
● When the Breeze Mode function is turned off
while the Forest Air™ system is on, the
Breeze Mode function will remain off until
the “
” button is turned off and on
again.
Outside odor and exhaust gas detection sensor :
This vehicle is equipped with an outside odor
and exhaust gas detection sensor. When the
automatic intake air control is on, the sensor
detects odors and exhaust gas, and then the
system automatically changes from the outside
air circulation mode to the recirculation mode.
When the “
” button is pushed, the out-
side odor and exhaust gas detection sensor will
turn on.
When the Forest Air™ system is on, for the first
40 seconds, the recirculation mode is selected
to prevent dust, dirt and pollen from entering
the vehicle, and the system cleans the air inside
of the vehicle with Plasmacluster ion™ that are
emitted from the ventilator. After 40 seconds,
the outside odor and exhaust gas sensor acti- vates and automatically alternates between the
recirculation mode and outside air circulation
mode.
●
The outside odor and exhaust gas detection
sensor detects industry odors such as pulp
or chemicals, and exhaust gas such as gaso-
line or diesel.
Inside Air Quality sensor :
This vehicle is equipped with an inside air
quality sensor. When the sensor detects odor in
the cabin, the system increases the fan speed
automatically. When the Forest Air™ system is
on, the inside air quality sensor will turn on.
This function will activate approximately 5 min-
utes after the engine has been started.
● The Outside/Inside Air Mix function will turn
off when the air recirculation and outside air
circulation modes are changed manually.
When the Outside/Inside Air Mix function is
not active, turn off and on the Forest Air™
system, the Outside/Inside Air Mix function
will activate again.
Auto humidity control :
The sensor installed on the upper side of the
windshield detects the temperature and humid-
ity of the passenger compartment and the sur-
face of the windshield, and controls the humid-
ity of the passenger compartment to not be
4-40Monitor, climate, audio, phone and voice recognition systems
—
—
03/02/10—pattie


over-dry or moist enough to fog the windows.
Moreover, it detects potential fog before forma-
tion on the windows and operates to remove it.
●Push the “AUTO” or “
” button (The
“AUTO” or “
” indicator light on the
button will illuminate and “AUTO DEF” will
appear on the display.)
● The “Auto humidity control” function will not
operate if the fan speed or a vent outlet is
manually adjusted. (“AUTO DEF” will disap-
pear from the display.)
● When auto humidity control is turned off
while the Forest Air™ system is on, turn off
and on the Forest Air™ system, the auto
humidity control will activate again.
Setting Forest Air™
1. Push the “CLIMATE” button on the instru-
ment panel and turn the display to the
“CLIMATE mode” screen.
2. Select the “Forest Air Setting” key.
The Forest Air™ system settings screen is
displayed.
● No settings, except for auto humidity con-
trol, are available unless the “
” indi-
cator light on the button illuminates.
Breeze Mode ON/OFF :
When this item is turned to ON, the Breeze
Mode function will activate while the Forest
Air™ system operates. Fan Speed Variance :
Set the Breeze Mode fluctuation effect.
Select the “Fan Speed Variance” key and select
the “High” or “Low” key setting of the Breeze
Mode fluctuation effect.
Setting the fan speed to “High” allows a larger
fluctuation change.
Outside/Inside Air Mix :
This item allows the user to set priority between
the outside air circulation and air recirculation
modes.
Select the “Outside/Inside Air Mix” key and use
“
”or“” key to adjust priority.
Greater priority will be given to the air recircu-
lation mode when the indicator is closer to
“
”, and the outside air circulation mode
when the indicator is closer to “
”.
Auto Defogging Sensitivity :
This item allows the user to set the timing of the
automatic defogging activation function.
Select the “Auto Defogging Sensitivity” key and
select the “Slow” or “Fast” key.
When set to OFF, the automatic defogging func-
tion will turn off.
SAA2961
Monitor, climate, audio, phone and voice recognition systems4-41
—
—
03/02/10—pattie