2011 INFINITI G-CONVERTIBLE garage door opener

WARNING
●Do not use HomeLink Universal Transceiver
with any garage door opener that lacks
safety stop and reverse features as required
by federal safety standards. (These stan-
dards became effective for opener models
manufactured after April 1, 1982.) A garage
door opener which cannot detect an object in
the path of a closing garage door and then
automatically stop and reverse, does not
meet current federal safety standards. Using
a garage door opener without these features
increases the risk of serious injury or death.
● During programming procedure, your garage
door or security gate may open or close.
Make sure that people and objects are clear
of the garage door, gate, etc. that you are
programming.
● Your vehicle’s engine should be turned off
while programming HomeLink Universal
Transceiver.
PROGRAMMING HOMELINK
To program your HomeLink Transceiver to op-
erate a garage door, gate, or entry door opener,
home or office lighting, you need to be at the
same location as the device. Note: Garage door
openers (manufactured after 1996) have “rolling
code protection”. To program a garage door
opener equipped with “rolling code protection”;
you will need to use a ladder to get up to the
garage door opener motor to be able to access
the “smart or learn” program button.
1. To begin, push and hold the 2 outer HomeLink buttons (to clear the memory)
until the indicator light
Ablinks (after 20
seconds). Release both buttons.
2. Position the end of the hand-held trans- mitter 1-3 inches away from the
HomeLink surface.
SIC3612
2-52Instruments and controls

3. Using both hands, simultaneously pushand hold both the HomeLink button you
want to program and the hand-held trans-
mitter button.
DO NOT release the buttons until step 4
has been completed. 4. Hold down both buttons until the indica-
tor light on HomeLink flashes, changing
from a “slow blink” to a “rapid blink”.
This could take up to 90 seconds. When
the indicator light blinks rapidly, both
buttons may be released. The rapidly
flashing light indicates successful pro-
gramming. To activate the garage door or
other programmed device, push and hold
the programmed HomeLink button - re-
leasing when the device begins to acti-
vate.
5. If the indicator light on HomeLink blinks
rapidly for two seconds and then turns
solid, HomeLink has picked up a “rolling
code” garage door opener signal. You will
need to proceed with the next steps to
train HomeLink, completing the pro-
gramming may require a ladder and an-
other person for convenience.
6. Push and release the program button located on the garage door opener’s mo-
tor to activate the “training mode”. This
button is usually located near the an-
tenna wire that hangs down from the
motor. If the wire originates from under a
light lens, you will need to remove the
lens to access the training button. NOTE:
Once you have pushed and released the
training button on the garage door open-
er’s motor and the “training light” is lit,
you have 30 seconds in which to perform
step 7. For convenience, use the help of a
second person to assist when performing
this step.
7. Quickly (within 30 seconds of pushing and releasing the garage door opener
training button) and firmly push and re-
lease the HomeLink button you’ve just
programmed. Push and release the
HomeLink button up to three times to
complete the training.
8. Your HomeLink button should now be
programmed. To program the remaining
HomeLink buttons for additional door or
gate openers, follow steps 2 through 8
only.
NOTE:
Do not repeat step 1 unless you want to “clear”
all previously programmed HomeLink buttons.
If you have any questions or are having diffi-
culty programming your HomeLink buttons,
please refer to the HomeLink web site at:
www.homelink.com or call 1-800-355-3515.
SIC3613
Instruments and controls2-53

PROGRAMMING HOMELINKFOR
CANADIAN CUSTOMERS
Prior to 1992, D.O.C. regulations required hand-
held transmitters to stop transmitting after 2
seconds. To program your hand-held transmit-
ter to HomeLink, continue to push and hold
the HomeLink button (note steps 2 through 4
under “Programming HomeLink”) while you
push and re-push (“cycle”) your hand-held
transmitter every 2 seconds until the indicator
light flashes rapidly (indicating successful pro-
gramming).
NOTE:
If programming a garage door opener, etc., it is
advised to unplug the device during the “cy-
cling” process to prevent possible damage to
the garage door opener components.
OPERATING THE HOMELINK
UNIVERSAL TRANSCEIVER
HomeLink Universal Transceiver (once pro-
grammed) may now be used to activate the
garage door, etc. To operate, simply push the
appropriate programmed HomeLink Universal
Transceiver button. The red indicator light will
illuminate while the signal is being transmitted.
PROGRAMMING TROUBLE-DIAGNOSIS
If HomeLink does not quickly learn the hand-
held transmitter information:
● replace the hand-held transmitter batteries
with new batteries.
● position the hand-held transmitter with its
battery area facing away from the
HomeLink surface.
● push and hold both the HomeLink and
hand-held transmitter buttons without inter-
ruption.
● position the hand-held transmitter 2 to 5 in
(50 to 127 mm) away from the HomeLink
surface. Hold the transmitter in that position
for up to 15 seconds. If HomeLink is not
programmed within that time, try holding
the transmitter in another position - keeping
the indicator light in view at all times.
If you continue to have programming difficul-
ties, please contact the INFINITI Consumer Af-
fairs Department. The phone numbers are lo-
cated in the Foreword of this Owner’s Manual.
CLEARING THE PROGRAMMED
INFORMATION
Individual buttons cannot be cleared, however
to clear all programming, push and hold the two
outside buttons and release when the indicator
light begins to flash (in approximately 20 sec-
onds).
REPROGRAMMING A SINGLE
HOMELINK BUTTON
To reprogram a HomeLink Universal Trans-
ceiver button, complete the following.
1. Push and hold the desired HomeLink button. Do notrelease the button until
step 4 has been completed.
2. When the indicator light begins to flash slowly (after 20 seconds), position the
hand-held transmitter 2 to 5 in (50 to 127
mm) away from the HomeLink surface.
3. Push and hold the hand-held transmitter button.
4. The HomeLink indicator light will flash,
first slowly and then rapidly. When the
indicator light begins to flash rapidly,
release both buttons.
2-54Instruments and controls

FluidAutomatic transmission fluid (ATF) .....8-11
Brake and clutch fluid ............8-12
Brake fluid ................. .8-12
Capacities and recommended fuel/
lubricants .................. .9-2
Engine coolant ................ .8-7
Engine oil .................. .8-8
Power steering fluid .............8-11
Window washer fluid .............8-13
FM-AM-SAT radio with Compact Disc (CD)
player ...................... .4-53
Fog light switch ................ .2-36
Front passenger air bag and status light . . .1-42
Front power seat adjustment ...........1-3
Front seat, Front seat adjustment ........1-3
Front-seat active head restraints ........1-10
Fuel Capacities and recommended fuel/
lubricants .................. .9-2
Fuel economy ................ .5-43
Fuel economy information (display) .....4-9
Fuel octane rating .............. .9-3
Fuel recommendation .............9-3
Fuel-filler cap ................ .3-30
Fuel-filler door ............... .3-30
Gauge ..................... .2-7
LOOSE FUEL CAP warning ..........3-32
Fuses ...................... .8-20
Fusible links .................. .8-20
G
Garage door opener, HomeLink Universal
Transceiver ................... .2-51Gascap.....................
.3-30
Gauge ....................... .2-4
Engine coolant temperature gauge .....2-6
Fuel gauge .................. .2-7
Odometer ................... .2-5
Speedometer ................. .2-5
Tachometer ................. .2-6
Trip computer ............... .2-23
General
maintenance .............. .8-2
Glove box .................... .2-44
H
Hands-free phone system, Bluetooth
(models with navigation system) ........4-85
Hands-free phone system, Bluetooth
(models without navigation system) ......4-96
Hard top If the top does not open or close .....3-24
Indicators for retractable hard top
(dot matrix) .............. .2-21, 3-22
Initializing .................. .3-25
Operating using the Intelligent Key . . . .3-25
Retractable hard top operation .......3-18
Hazard warning flasher switch .........2-36
Head restraints .................. .1-7
Headlights Bulb replacement ............. .8-25
Headlight switch .............. .2-32
Xenon headlights .............. .2-31
Heated seats .................. .2-37
Heater Automatic climate control ..........4-29
Engine block heater .............5-55
HomeLink Universal Transceiver ........2-51Hood release
.................. .3-17
Horn ....................... .2-37
I
Ignition switch (Push-button) ................. .5-7
Manual transmission models . . . . . . . .5-16
Immobilizer system .............. .2-27
In-cabin microfilter ............... .4-36
Indicator Dot matrix display ............. .2-16
Lights .................... .2-13
INFINITI Vehicle Immobilizer System ......2-27
INFINITI voice recognition system . . . . . . .4-109
INFO button ................... .4-8
Inside mirror .................. .3-34
Inspection/maintenance
(I/M) test.......9-22
Instrument brightness control .........2-35
Instrument panel ................ .2-3
Intelligent cruise control (ICC) system .....5-21
Preview function .............. .5-42
Intelligent Cruise Control (ICC) system
warning light .................. .2-10
Intelligent Key .................. .3-2
Intelligent Key battery discharge indicator . .2-19
Intelligent Key insertion indicator . ......2-18
Intelligent Key removal indicator ........2-18
Intelligent Key system ..............3-6
Battery replacement .............8-22
Key operating range .............3-8
Key operation ................ .3-9
Warning light ................ .2-10
Warning signals ............... .3-11
Intelligent Key warning light ..........2-10
10-3