2011 INFINITI G-CONVERTIBLE seat adjustment

●Do not operate the retractable hard top in a
strong wind. It could be blown by the wind,
striking someone or damaging the retract-
able hard top.
● When the retractable hard top is retracted,
do not allow anyone to stand up or extend
any portion of their body out of the opening
while the vehicle is in motion or while the
retractable hard top is being operated.
● In an accident you could be thrown from the
vehicle with an open retractable hard top if
you do not use seat belts. Always use seat
belts and proper child restraints.
● Do not place any objects on or near the re-
tractable hard top operating switch. Unin-
tentional operation of the retractable hard
top may cause injuries or an accident if the
objects press the switch.
● Do not put your fingers or hands in the gap
between the rear seats and the rear parcel
shelf or the side flaps. Doing so may cause
injury if the retractable hard top is operated.CAUTION
● Do not operate the retractable hard top when
the temperature is below 32°F (0°C). This
may result in damage to the retractable hard
top material or operating system.
● Remove water drops, snow, ice or sand from
the retractable hard top, and dry the surface
of the retractable hard top completely before
opening it.
● Do not open the retractable hard top when it
is wet or damp. If the retractable hardtop and
rear window are wet, water might get inside
of the vehicle. To avoid this, wipe off any
water drops before opening the retractable
hard top.
● Do not place any objects between the hard
rail and the structure. Doing so could inter-
fere with retractable hard top operation and
cause damage to the retractable hard top
operating system or the objects.
● Do not place any objects on the upper area of
the windshield glass or the hard rail when
the retractable hard top is fully opened. Do-
ing so could interfere with retractable hard
top operation and cause damage. ●
Do not place any object between the retract-
able hard top when the retractable hard top
is stored in the storage space. Doing so may
interfere with retractable hard top operation
and cause damage.
● Do not place anything on the retractable
hard top, rear parcel shelf, side flaps and
trunk lid. Even small items may interfere
with the retractable hard top operation and
could cause damage to the retractable hard
top or the vehicle body.
● Do not place anything in the retractable hard
top storage area. The retractable hard top
will not fit there properly, and this could
damage the retractable hard top and/or the
vehicle body.
● Do not sit or place excessive weight on the
top, rear parcel shelf, side flaps and trunk
lid, especially when the retractable hard top
is being operated. The retractable hard top
may be damaged.
● Do not drive the vehicle with the retractable
hard top partially opened. Always make sure
the retractable hard top is either fully
opened or closed before driving.
● Secure items so that they cannot be blown
from the vehicle while driving with the re-
tractable hard top open.
Pre-driving checks and adjustments3-19

WARNING
●Do not adjust the steering wheel while driv-
ing. You could lose control of your vehicle
and cause an accident.
● Do not adjust the steering wheel any closer
to you than is necessary for proper steering
operation and comfort. The driver’s air bag
inflates with great force. If you are unre-
strained, leaning forward, sitting sideways
or out of position in any way, you are at
greater risk of injury or death in a crash. You
may also receive serious or fatal injuries
from the air bag if you are up against it when
it inflates. Always sit back against the seat-
back and as far away as practical from the
steering wheel. Always use the seat belts.
MANUAL OPERATION (if so equipped)
Tilt or telescopic operation
Pull the lock lever1down and adjust the
steering wheel up, down, forward or rearward to
the desired position.
Push the lock lever up securely to lock the
steering wheel in place.
ELECTRIC OPERATION (if so equipped)
Tilt or telescopic operation
Move the lever to adjust the steering wheel up
or down, forward or rearward to the desired
position.
For more information, see “AUTOMATIC DRIVE
POSITIONER” later in this section.
SPA2328SPA2312
TILT/TELESCOPIC STEERING
Pre-driving checks and adjustments3-33

The automatic drive positioner system has two
features:
●Seat synchronization function
● Memory storage
SEAT SYNCHRONIZATION FUNCTION
The seat synchronization function automatically
adjusts the positions of the steering wheel and
outside mirrors when the seat is adjusted using
the power seat switches.
However, the steering wheel and outside mir-
rors will not move if the seat is adjusted over
the maximum thresholds. The system considers
that the steering wheel and outside mirror
adjustments are not necessary because the
seat may not be adjusted for the driving posi-
tion. Note that the function is set to disabled as
the factory default setting. The seat synchronization function operates un-
der the following conditions:
●
The ignition switch is in the ON position.
● The selector lever is in the P (Park) position
(Automatic Transmission models) or the
parking brake is applied (Manual Transmis-
sion models).
● The seatback is raised.
If the outside mirrors or the steering wheel
reaches its maximum adjustment, the function
is automatically disabled. Restart the function
by selecting a previously stored seat memory
position using the memory switches (1 or 2). An
Intelligent Key that was previously linked to the
stored seat memory can also be used to restart
the function.
If a seat position was not previously stored in
the seat memory, restart the function by adjust-
ing the steering wheel and outside mirrors
manually for your best driving position and then
drive the vehicle above 4 MPH (7 km/h).
SPA2659
AUTOMATIC DRIVE POSITIONER (if so
equipped)
Pre-driving checks and adjustments3-37

Cancel or activate seat
synchronization function
For Automatic Transmission models:
The selector lever must be in the P (Park)
position with the ignition switch in the ACC
position.
For Manual Transmission models:
The parking brake must be applied with the
ignition switch in the ACC position.
The seat synchronization function can be acti-
vated or canceled by pushing and holding the
SET switch for more than 10 seconds while the
ignition switch is in the ACC position.
The indicator lights on the memory switches (1
and 2) will blink once when the function is
canceled, and the indicator lights will blink
twice when the function is activated. Note that
the indicator lights may illuminate after 5 sec-
onds while holding the SET switch. This indi-
cates readiness for linking the Intelligent Key to
a stored memory position. Keep the SET switch
pushed for more than 10 seconds to turn on or
off the seat synchronization function.
MEMORY STORAGE
Two positions for the driver’s seat, steering
column and outside mirrors can be stored in the
automatic drive positioner memory. Follow
these procedures to use the memory system.
1.Automatic transmission models:
Move the selector lever to the P (Park)
position.
Manual transmission models:
Apply the parking brake.
2. Raise the seatback.
3. Push the ignition switch to the ON posi-
tion.
4. Adjust the driver’s seat, steering column and outside mirrors to the desired posi-
tions by manually operating each adjust-
ing switch. For additional information, see
“SEATS” in the “1. Safety — Seats, seat
belts and supplemental restraint system”
section and “TILT/TELESCOPIC STEERING”
page 3-33 and “OUTSIDE MIRRORS” ear-
lier in this section. 5. Push the SET switch and, within 5 sec-
onds, push the memory switch (1 or 2)
fully for at least 1 second.
The indicator light for the pushed memory
switch will stay on for approximately 5 sec-
onds after pushing the switch.
If memory is stored in the same memory
switch, the previous memory will be deleted.
Linking Intelligent Key to a stored
memory position
The Intelligent Key can be linked to a stored
memory position with the following procedure.
1. Follow the steps for storing a memoryposition.
2. While the indicator light for the memory switch being set is illuminated for 5 sec-
onds, push the
button on the Intel-
ligent Key. If the indicator light blinks, the
Intelligent Key is linked to that memory
setting.
Push the ignition switch to the OFF position,
and then push thebutton on the Intelli-
gent Key. The driver’s seat, steering wheel and
outside mirrors will move to the memorized
position.
3-38Pre-driving checks and adjustments

Confirming memory storage
●Push the ignition switch to the ON position
and push the SET switch. If the main memory
has not been stored, the indicator light will
come on for approximately 0.5 second.
When the memory has stored in position, the
indicator light will stay on for approximately
5 seconds.
● If the battery cable is disconnected, or if the
fuse opens, the memory will be canceled. In
this case, reset the desired position using
the previous procedure.
● If optional Intelligent Keys are added to your
vehicle, the memory storage procedure to
switch 1 or 2 and linking Intelligent Key
procedure to a stored memory position
should be performed again for each Intelli-
gent Key. For additional Intelligent Key infor-
mation, see “KEYS” earlier in this section.
Selecting the memorized position
1. Automatic transmission models:
Move the selector lever to the P (Park)
position.
Manual transmission models:
Apply the parking brake.
2. Raise the seatback.
3. Use one of the following methods to move
the driver’s seat, the outside mirrors and
the steering wheel.
●Push the ignition switch to the ON position
and push the memory switch (1 or 2) fully for
at least 1 second.
● Within 45 seconds of opening the driver’s
door, push the memory switch (1 or 2) fully
for at least 1 second.
The driver’s seat, steering column and out-
side mirrors will move to the memorized
position with the indicator light flashing,
and then the light will stay on for approxi-
mately 5 seconds.
For manual transmission models, the memory
positions can be selected even when the engine
is running. In this case, move the shift lever to
the N (Neutral) position and apply the parking
brake. Then, perform step 2.
SYSTEM OPERATION
The automatic drive positioner system will not
work or will stop operating under the following
conditions:
● When the vehicle speed is above 4 MPH (7
km/h).
● When the adjusting switch for the driver’s
seat and steering column is turned on while
the automatic drive positioner is operating.
● When the memory switch 1 or 2 is not
pushed for at least 1 second.
● When the seat, steering column and outside
mirrors have already been moved to the
memorized position.
● When no position is stored in the memory
switch.
● When the parking brake is released (MT
models).
● When the speed is above 4 MPH (7 km/h)
while the parking brake is applied (MT mod-
els).
To restart the drive positioner system, move
the parking brake to off and on.
● When the engine is started while moving the
automatic drive positioner.
Pre-driving checks and adjustments3-39

●When the driver’s door remains open for
more than 45 seconds and the ignition
switch is not in the ON position.
● When the seatback is folded.
● While the walk-in function operates.
● The seat synchronization function is auto-
matically disabled if the outside mirrors or
steering wheel reaches its maximum adjust-
ment.
● The seat synchronization function will not
move if the seat is adjusted over one of the
following maximum thresholds:
– Seat sliding: 3.0 in (76 mm)
– Seatback reclining: 9.1 degrees
– Seat lifter (rear side): 0.8 in (20 mm)
3-40Pre-driving checks and adjustments

Display settings (models with
navigation system)
The display as illustrated will appear when
pushing the SETTING button and selecting the
“Display” key.
Display Adjustment :
To adjust the display settings, select the “Dis-
play Adjustment” key. The following settings
are available.
●Display
To turn off the screen, push the ENTER button
and turn the “Display” indicator off. The other
method is to push and hold the “
OFF”
button for more than 2 seconds. When any mode button is pushed with the
screen off, the screen turns on for further
operation. The screen will turn off automatically
5 seconds after the operation is finished.
To turn on the screen, set this item to the ON
position, or push and hold the “
OFF”
button.
● Brightness/Contrast/Background Color
To adjust the brightness and contrast of the
screen, select the “Brightness” or “Contrast”
key.
Then, you can adjust the brightness and the
contrast using the INFINITI controller.
For information on the “Background Color” key,
refer to the separate Navigation System Own-
er’s Manual.
Operating tips :
Depending on the driver’s seat positions or the
weather conditions, the display could be hard
to read. Adjust the brightness and contrast of
the display on the setting screen.
Color Theme :
Choose the theme color of the menu screen
from “Black”, “Brown” or “Silver”.
DISPLAY settings (models without
navigation system)
The “Display” screen will appear when pushing
the SETTING button, selecting “Display” key
with the INFINITI controller and pushing the
ENTER button.
Display :
To turn off the screen, push the ENTERbutton
and turn the “ON” indicator off.
When any mode button is pushed with the
screen off, the screen turns on for further
operation. The screen will turn off automatically
5 seconds after the operation is finished.
SAA2486SAA2115
Monitor, climate, audio, phone and voice recognition systems4-15

FluidAutomatic transmission fluid (ATF) .....8-11
Brake and clutch fluid ............8-12
Brake fluid ................. .8-12
Capacities and recommended fuel/
lubricants .................. .9-2
Engine coolant ................ .8-7
Engine oil .................. .8-8
Power steering fluid .............8-11
Window washer fluid .............8-13
FM-AM-SAT radio with Compact Disc (CD)
player ...................... .4-53
Fog light switch ................ .2-36
Front passenger air bag and status light . . .1-42
Front power seat adjustment ...........1-3
Front seat, Front seat adjustment ........1-3
Front-seat active head restraints ........1-10
Fuel Capacities and recommended fuel/
lubricants .................. .9-2
Fuel economy ................ .5-43
Fuel economy information (display) .....4-9
Fuel octane rating .............. .9-3
Fuel recommendation .............9-3
Fuel-filler cap ................ .3-30
Fuel-filler door ............... .3-30
Gauge ..................... .2-7
LOOSE FUEL CAP warning ..........3-32
Fuses ...................... .8-20
Fusible links .................. .8-20
G
Garage door opener, HomeLink Universal
Transceiver ................... .2-51Gascap.....................
.3-30
Gauge ....................... .2-4
Engine coolant temperature gauge .....2-6
Fuel gauge .................. .2-7
Odometer ................... .2-5
Speedometer ................. .2-5
Tachometer ................. .2-6
Trip computer ............... .2-23
General
maintenance .............. .8-2
Glove box .................... .2-44
H
Hands-free phone system, Bluetooth
(models with navigation system) ........4-85
Hands-free phone system, Bluetooth
(models without navigation system) ......4-96
Hard top If the top does not open or close .....3-24
Indicators for retractable hard top
(dot matrix) .............. .2-21, 3-22
Initializing .................. .3-25
Operating using the Intelligent Key . . . .3-25
Retractable hard top operation .......3-18
Hazard warning flasher switch .........2-36
Head restraints .................. .1-7
Headlights Bulb replacement ............. .8-25
Headlight switch .............. .2-32
Xenon headlights .............. .2-31
Heated seats .................. .2-37
Heater Automatic climate control ..........4-29
Engine block heater .............5-55
HomeLink Universal Transceiver ........2-51Hood release
.................. .3-17
Horn ....................... .2-37
I
Ignition switch (Push-button) ................. .5-7
Manual transmission models . . . . . . . .5-16
Immobilizer system .............. .2-27
In-cabin microfilter ............... .4-36
Indicator Dot matrix display ............. .2-16
Lights .................... .2-13
INFINITI Vehicle Immobilizer System ......2-27
INFINITI voice recognition system . . . . . . .4-109
INFO button ................... .4-8
Inside mirror .................. .3-34
Inspection/maintenance
(I/M) test.......9-22
Instrument brightness control .........2-35
Instrument panel ................ .2-3
Intelligent cruise control (ICC) system .....5-21
Preview function .............. .5-42
Intelligent Cruise Control (ICC) system
warning light .................. .2-10
Intelligent Key .................. .3-2
Intelligent Key battery discharge indicator . .2-19
Intelligent Key insertion indicator . ......2-18
Intelligent Key removal indicator ........2-18
Intelligent Key system ..............3-6
Battery replacement .............8-22
Key operating range .............3-8
Key operation ................ .3-9
Warning light ................ .2-10
Warning signals ............... .3-11
Intelligent Key warning light ..........2-10
10-3