2011 HONDA CR-Z tires

218
Driving
When Driving Tire Pressure Monitoring System (TPMS) - Required Federal Explanation
Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly.
Main MenuTable of Contents

Maintenance
This chapter discusses basic maintenance.
237
Before Performing Maintenance
Inspection and Maintenance ................... 238
Safety When Performing Maintenance ... 239Parts and Fluids Used in Maintenance
Service .................................................. 240
Maintenance Minder ™
............................ 241
Maintenance Under the Hood Maintenance Items Under the Hood ....... 245
Opening the Hood ................................. 246
Recommended Engine Oil ...................... 247
Oil Check ............................................... 248
Adding Engine Oil .................................. 249
Changing the Engine Oil and Oil Filter .... 250 Engine Coolant ...................................... 252
Transmission Fluid .................................. 254
Brake/Clutch Fluid .................................. 256
Refilling Window Washer Fluid ............... 257
Replacing Light Bulbs ............................. 258
Checking and Maintaining Wiper Blades Checking Wiper Blades ........................... 266
Changing the Front Wiper Blade Rubber 266
Changing the Rear Wiper Blade Rubber .. 268
Checking and Maintaining Tires Checking Tires ........................................ 269
Tire and Loading Information Label ........ 270
Tire Labeling ........................................... 270 DOT Tire Quality Grading (U.S. Vehicles)
.272
Wear Indicators ...................................... 274
Tire Service Life ...................................... 274
Tire and Wheel Replacement .................. 275
Tire Rotation .......................................... 276
Winter Tires ............................................ 277
12 Volt Battery ........................................ 278
Remote Transmitter Care ....................... 279
Replacing the Battery ............................. 279
Climate Control System Maintenance ... 280
Cleaning ................................................... 281
Interior Care ........................................... 281
Exterior Care .......................................... 283
Main Menu

238
Maintenance
Before Performing Maintenance
Inspection and Maintenance
For your safety, perform all listed inspections and maintenance to keep your vehicle
in good condition. If you become aware of any abnormality (noise, smell, insufficient brake fluid, oil residue on the ground, etc.), have your vehicle inspected by a dealer. (Note, however, that service at a dealer is not mandatory to keep your warranties in effect.) Refer to the separate maintenance booklet for detailed maintenance and inspection information.Types of Inspection and Maintenance

■
Daily Inspections
■
Perform inspections before long distance trips, when washing the vehicle, or when refueling.
Periodic Inspections
■
Check the automatic transmission fluid level monthly.
•
Automatic Transmission Fluid P.254
Check the brake fluid level monthly.
•
Brake/Clutch Fluid P.256
Check the tire pressure monthly. Examine the tread for wear and foreign objects.
•
Checking and Maintaining Tires P.269
Check the operation of the headlights, parking lights, taillights, high-mount
•
brake light, and license plate lights monthly.
Replacing Light Bulbs P.258
Check the condition of the wiper blades at least every six months.
•
Checking and Maintaining Wiper Blades P.266
Inspection and Maintenance
U.S. models only Maintenance, replacement, or repair of emissions control devices and systems may be done by any automotive repair establishment or individual using parts that are "certiied" to EPA standards. According to state and federal regulations, failure to perform maintenance on the items marked with # will not void your emissions warranties. However, all maintenance services should be performed in accordance with the intervals indicated by the multi-information display.
Maintenance Service Items P. 2 4 3
If you want to perform complex maintenance tasks that require more skills and tools, purchase the service manual.
Authorized Manuals P. 3 1 9
If you want to perform maintenance yourself, make sure that you have the necessary tools and skills irst.After performing maintenance, complete the records in the separate maintenance booklet.
Main MenuTable of Contents

243
Maintenance
Maintenance Minder™
Maintenance Service Items
■
System Message Indicator Maintenance Minder Message
Sub Items
Main Item
Maintenance Service Items
Independent of the maintenance minder
•
messages, replace the brake luid every 3 years. Inspect idle speed every 160,000 miles (256,000
•
km).Adjust the valves during services A, B, 1, 2, or 3
•
only if they are noisy.
*1: Change the engine oil according to the maintenance minder messages, or annually, whichever comes irst.
*2: If you drive in dusty conditions, replace the air cleaner element every 15,000 miles (24,000 km).
*3: If you drive primarily in urban areas that have high concentrations of soot in the air from industry and from diesel-powered vehicles, replace the dust and pollen ilter every 15,000 miles (24,000 km).
#: See information on maintenance and emissions warranty.
Code Maintenance Main Items
A Replace engine oil*
• 1
B Replace engine oil*
• 1
and oil filter
Inspect front and rear brakes
•
Check parking brake adjustment
•
Inspect tie rod ends, steering gear
•
box, and boots
Inspect suspension components
•
Inspect driveshaft boots
•
Inspect brake hoses and lines
•
(including ABS/VSA ®
)
Inspect all fluid levels and
•
condition of fluids
Inspect exhaust system
• #
Inspect fuel lines and connections
• #Code Maintenance Sub Items
1 Rotate tires •
2 Replace air cleaner element* • 2
Replace dust and pollen
•
filter* 3
Inspect drive belt
•
3 Replace transmission fluid •
4 Replace spark plugs •
Inspect valve clearance
•
5 Replace engine coolant •
Main MenuTable of Contents

269
Maintenance
Checking and Maintaining Tires
Checking Tires To safely operate your vehicle, your tires must be of the proper type and size, in good condition with adequate tread, and properly inflated.Inflation Guidelines
■
Properly inflated tires provide the best combination of handling, tread life, and
comfort. Refer to the driver’s doorjamb label or specification’s page for the specified pressure. Underinflated tires wear unevenly, adversely affect handling and fuel economy, and are more likely to fail from overheating. Overinflated tires make your vehicle ride harshly, are more prone to road hazard, and wear unevenly. Every day before you drive, look at each of the tires. If one looks lower than the others, check the pressure with a tire gauge. At least once a month or before long trips, use a gauge to measure the pressure in all tires, including the spare. Even tires in good condition can lose 1 to 2 psi (10 to 20 kPa, 0.1 to 0.2 kgf/cm 2
) per month.
Inspection Guidelines
■
Every time you check inflation, also examine the tires and valve stems.Look for:
Bumps or bulges on the side or in the tread. Replace the tire if you find any.
•
Cuts, splits, or cracks in the side of the tire. Replace it if you see fabric or cord.Remove any foreign objects and inspect for air leaks.
•
Uneven tread wear. Have your dealer check the wheel alignment.
•
Excessive tread wear.
•
Wear Indicators P.274
Checking Tires
Measure the air pressure when tires are cold. This means the vehicle has been parked for at least three hours, or driven less than 1 mile (1.6 km). If necessary, add or release air until the speciied pressure is reached. If checked when hot, tire pressure can be as mush as 4–6 psi (30–40 kPa, 0.3–0.4 kgf/cm 2
) higher
than if checked when cold.
Have a dealer check the tires if you feel a consist ent
vibration while driving. New tires and any that have been removed and reinstalled should be properly balanced.
WARNING
Using tires that are excessively worn or improperly inflated can cause a crash in which you can be seriously hurt or killed. Follow all instructions in this owner’s manual regarding tire inflation and maintenance.
Main MenuTable of Contents

270
Maintenance
Checking and Maintaining Tires Tire and Loading Information Label Tire Labeling
Tire and Loading Information Label
The label attached to the drive’s doorjamb provides necessary tire and loading information. Tire LabelingThe tires that came on your vehicle have a
number of markings. Those you should be
aware of are described below.
Tire Size

■
Whenever tires are replaced, they should be replaced with tires of the same
size.
1
2
43
Label Example
Tire and Loading Information Label
The tire and loading information label attached to the driver’s doorjamb contains:
1 The number of people your vehicle can carry.
2 The total weight your vehicle can carry. Do not exceed this weight.
3 The original tire sizes for front, rear and spare.
4 The proper cold tire pressure for
front, rear and spare.
Maxi mum
Tire Pressure
Tire
Size
Tire
Identiication Number (TIN)
Tire SizeMaxi
mum
Tire Load
Example
Tire Size
Following is an example of tire size with
an explanation of what each component
means.
P195/55 R16 86V
P: Vehicle type (P indicates passenger
vehicle).
195: Tire width in millimeters.
55: Aspect ratio (the tire’s section height
as a percentage of its width).
R: Tire construction code (R indicates
radial).
16: Rim diameter in inches.
86: Load index (a numerical code
associated with the maximum load the
tire can carry).
V: Speed symbol (an alphabetical code
indicating the maximum speed rating).
Main MenuTable of Contents

271
Maintenance
Checking and Maintaining Tires Tire Labeling
Tire Identiication Number (TIN)
■
The tire identification number (TIN) is a group of numbers and letters that look like the example in the side column. TIN is located on the sidewall of the tire.
Glossary of Tire Terminology

■
Cold Tire Pressure – The tire air pressure when the vehicle has been parked
for at least three hours or driven less than 1 mile (1.6 km). Load Rating – Means the maximum load that a tire is rated to carry for a
given inflation pressure.Maximum Inflation Pressure – The maximum tire air pressure that the
tire can hold.Maximum Load Rating – Means the load rating for a tire at the maximum
permissible inflation pressure for that tire.Recommended Inflation Pressure – The cold tire inflation pressure
recommended by the manufacturer.Treadwear Indicators (TWI) – Means the projections within the principal
grooves designed to give a visual indication of the degrees of wear of the tread.
Tire Identiication Number (TIN)
DOT B97R FW6X 2209 DOT: This indicates that the tire meets all requirements of the U.S. Department of Transportation.B97R: Manufacturer’s identiication mark.FW6X: Tire type code.2209: Date of manufacture.
Year Week
Main MenuTable of Contents

272
Maintenance
Checking and Maintaining Tires DOT Tire Quality Grading (U.S. Vehicles)
DOT Tire Quality Grading (U.S. Vehicles)
The tires on your vehicle meet all U.S. Federal Safety Requirements. All tires are also graded for treadwear, traction, and temperature performance according to Department of Transportation (DOT) standards. The following explains these gradings.Uniform Tire Quality Grading

■
Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
Treadwear

■
The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations
in driving habits, service practices and difference s in road characteristics and
climate.
Uniform Tire Quality Grading
For example: Treadwear 200Traction AATemperature A All passenger car tires must conform to Federal Safety Requirements in addition to these grades.
Main MenuTable of Contents