2011 FORD KUGA ECT

E84836
308-640
Pointer symbols are used to draw attention to
components and give special instructions such as
a required sequence or number of components.
The number of components is reflected by the
value inside the luty arrow. A sequence number islocated inside the circle. Numbers inside circles
are also used to allocate special information such
as tightening torques or chemicals to a particular
component.
G836098en2008.50 Kuga8/2011
100-00-
14
General Information
100-00- 14
DESCRIPTION AND OPERATION
TO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUAL

How to use Diagnosis and Testing
procedures
Inspection and Verification
Visual Inspection Charts, Symptom Charts and
other information charts (such as diagnostic
routines) or supplement test procedures with
technical specifications will navigate the user to a
specific test procedure.
Symptom Chart
The symptom chart indicates symptoms, sources
and actions to address a condition.
Pinpoint Tests
For electrical systems, pinpoint test steps are used
to identify the source of a concern in a logical,
step-by-step manner. Pinpoint tests have two
columns: CONDITIONS and
DETAILS/RESULTS/ACTIONS.
The CONDITIONS column is used exclusively for
graphics and icons (with or without captions) and
the DETAILS/RESULTS/ACTIONS column
provides direction to another test step or specific
corrective actions.
The boxed numbers indicate the order in which the
described action is to be carried out.
Component Tests
A component test is used when a component is
tested in multiple pinpoint tests, or if a procedure
is too complicated to be formatted within a single
page of the pinpoint test.
Graphics
Test graphics show the measurement or test to be
carried out in a test step.
A representative tester graphic is used for
voltmeters and ohmmeters.
If multiple measurements are made in a single
graphic, the test leads are drawn with a solid line
until the test lead splits to indicate the multiple
measurements, at which point dashed lines are
used.
Breakout box type testers are represented by a
double circle test pin. Test pins are labeled with
the pin number.
G836098en2008.50 Kuga8/2011
100-00-18
General Information
100-00- 18
DESCRIPTION AND OPERATION
TO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUAL

Description
Item
Convertible body style
5
Van body style
6
3, 4, 5-door body style - Top View
7
Wagon body style - Top View
8
Underview
9Description
Item
Right-hand drive (RHD) vehicle
10
Left-hand drive (LHD) vehicle
11
Gearshift lever and selector lever position symbols
Gearshift lever and selector lever position symbols
are used to show the lever position that is required
to be selected to carry out a procedure step.
E88972
12
4
10
3
7
65
8
9
G955392en2008.50 Kuga8/2011
100-00- 23
General Information
100-00- 23
DESCRIPTION AND OPERATION
TO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUAL

Description
Item
Minor component movement
clockwise/counterclockwise
1
Major component movement
clockwise/counterclockwise
2
Component movement to the
left/right/up/down
3
Component movement towards/away
4
3 dimensional component movement
5Description
Item
2 dimensional component movement
6
3 dimensional component rotation
7
3 dimensional component cycling
8
Turn Symbols
Turn symbols are used to provide further
information on the direction or angle of component
turns.
E88970
12
34
6
7
5
8
G955392en2008.50 Kuga8/2011
100-00- 20
General Information
100-00- 20
DESCRIPTION AND OPERATION
TO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUAL

Description
Item
Set the selector lever to the park (P)
position
1
Set the selector lever to the reverse ( R )
position
2
Set the selector lever to the neutral (N)
position
3
Set the selector lever to the drive (D)
position
4
Set the selector lever with manual shift
pattern to the park (D) position
5
Set the selector lever with manual shift
pattern to the manual (M) position
6Description
Item
Set the selector lever with manual shift
pattern to the shift down (-) position
7
Set the selector lever with manual shift
pattern to the shift up (+) position
8
Set the gearshift lever to the neutral (N)
position
9
Further gearshift lever positions that may
appear in illustrations
10
Screwdriver symbols
The screwdriver symbols are used to show which
screwdriver bit is recommended to carry out a
procedure step.
G955392en2008.50 Kuga8/2011
100-00-
24
General Information
100-00- 24
DESCRIPTION AND OPERATION
TO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUAL

Description
Item
Self contained breathing apparatus
4
General prohibition used in combination
with another symbol
5
Do not use power tools
6
Visual check
7
Noise check
8
Dispose the specified component
9
Replaced by item 9 (Dispose the specified
component)
10
Set the engine speed to the specified
value
11Description
Item
Fully apply the parking brake lever
12
Fully release the parking brake lever
13
Do not dispose of batteries into the waste
bin
14
Visual check using a mirror
15
Area/component must be dry
16
Mandatory Protective equipment - Health and safety
symbols
The protective equipment symbols advise to use
a mandatory protective equipment to avoid or at
least reduce possible health and safety risks.
G955392en2008.50 Kuga8/2011
100-00- 36
General Information
100-00- 36
DESCRIPTION AND OPERATION
TO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUAL

E89019
12
34
56
Description
Item
Wear protective gloves
1
Wear face guard
2
Wear safety goggles
3
Wear ear protectors
4
Wear safety goggles and ear protectors
5
Wear a respirator
6Prohibition - Health and safety symbols and
component damage
The prohibition symbols are used to prohibit the
specified actions to avoid or at least reduce
possible component damage and health and safety
risks.
G955392en2008.50 Kuga8/2011
100-00- 37
General Information
100-00- 37
DESCRIPTION AND OPERATION
TO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUAL

E89021
123
56
798
12
4
13
Description
Item
Hazardous voltage/Electrical
shock/Electrocution
1
Fire Hazard/Highly flammable
2
Burn hazard/Hot surface
3
Automatic start-up
4
Toxic
5
Explosive material
6
Battery hazard
7Description
Item
Corrosive material
8
Lifting hazard
9
Hand crush/Force from above
10
Cutting of fingers or hand
11
Pressure hazard
12
Invisible laser radiation. Do not view
directly with optical instruments
(magnifiers). Class 1M laser product
13
G955392en2008.50 Kuga8/2011
100-00-
39
General Information
100-00- 39
DESCRIPTION AND OPERATION
TO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUAL