2011 FORD FUSION (AMERICAS) garage door switch

Types of garage door openers (rolling code and fixed code)
The Car2UHome Automation System may be programmed to operate
rolling code and fixed code garage door openers.
•Rolling code garage door openers were produced after 1996 and are
code protected. Rolling code means the coded signal is changed every
time your remote control garage door opener is used.
•Fixed code garage door openers were produced prior to 1996. Fixed
code uses the same coded signal every time. It is manually
programmed by setting DIP switches for a unique personal code.
If you do not know if your garage
door opener is a rolling code or
fixed code device, open your garage
door opener’s remote control battery
cover. If a panel of DIP switches is
present your garage door opener is
a fixed code device. If not, your
garage door opener is a rolling code
device.
Note:Programming the Car2Usystem to a community gate will require
a unique set of instructions depending on the gate system model.
Contact the Car2Uhelp line at 1-866-572-2728 to program your Car2U
system.
Note:Accidentally entering the program mode may override previously
programmed buttons. This can happen by pressing and releasing the
outer two buttons, or all three buttons, simultaneously. If this happens,
do not press any button until the module times out after approximately
2.5 seconds and resets to normal mode. When time-out occurs, all three
LEDs will flash rapidly for a few seconds then turn off. Any settings
should remain as previously set.
Rolling code programming
Note:Programming the rolling code garage door opener involves
time-sensitive actions. Read the entire procedure prior to beginning so
you will know which actions are time-sensitive. If you do not follow the
time-sensitive actions, the device will time out and you will have to
repeat the procedure.
Note:Do not program the Car2Usystem with the vehicle in the garage.
Make sure that your key is on and engine off while programming the
transmitter.
12
34
5
6789
1
01
1
1
2
C
T
S
20
6-12 T
124
O
N
Driver Controls
89
2011 Fusion(fsn)
Owners Guide, 3rd Printing
USA(fus)

The indicator light above the selected button will turn on to confirm that
the Car2Usystem is responding to the button command.
To program another rolling code device such as an additional garage door
opener, a security device or home lighting, repeat Steps 1 through 4
substituting a different function button in Step 3 than what you used for
the garage door opener. For example, you could assign the left-most
button to the garage door, the center button to a security device, and
the right-most button to another garage door opener.
Note:The Car2Usystem allows for three devices to be programmed. If
you need to change or replace any of the three devices after it has been
initially programmed, it is necessary to erase the current settings using
theErasing the Car2UHome Automation System buttonsprocedure
and then programming all of the devices being used.
Fixed code programming
Note:Do not program the Car2Usystem with the vehicle in the garage.
Make sure that your key is on and engine off while programming the
transmitter.
1. To program units with fixed code DIP switches, you will need the
garage door hand-held transmitter, paper and a pen or pencil.
2. Open the battery cover and record the switch settings from left to
right for all 8 to 12 switches. Use the figure below:
When a switch is in the up, on, or + position, circle “L.”
When a switch is in the middle, neutral, or 0 position, circle “M.”
When a switch is in the down, off, or – position, circle “R.”
Driver Controls
91
2011 Fusion(fsn)
Owners Guide, 3rd Printing
USA(fus)

Switch
position1234567 8 9101112
Up, on
or +LLLLLLLLLLLL
Middle,
neutral
or 0MMMMMMMMMMMM
Down,
offor–RRRRRRRRRRRR
L=left; M=middle; R=right
3. To input these positions into the
Car2Usystem, simultaneously
press all three Car2Usystem
buttons for a few seconds and then
release to put the device into
programming mode. The indicator
lights will blink slowly. Within
2.5 minutes enter your
corresponding DIP switch settings
from left to right into your Car2Usystem by pressing and releasing the
buttons corresponding to the settings you circled.
4. After inputting switch settings, simultaneously press and release all
three Car2Usystem buttons. The indicator lights will turn on.
5. Press and hold the Car2U
system button you would like to use
to control the garage door.
Immediately (within 1 second)
release the button once the garage
door moves. During this time the
selected button indicator light will
blink slowly. Do not release the
button until you see the garage door move. Most garage doors open
quickly. You may need to hold the button from 5–55 seconds before
observing movement of the garage door.
6. The indicator light will (begin to) blink rapidly until programming is
complete. If your garage door opener does not operate following these
steps, repeat Steps 2 through 6. Otherwise, call the toll-free Car2Uhelp
line at 1-866-57Car2U (1-866-572-2728).
Driver Controls
92
2011 Fusion(fsn)
Owners Guide, 3rd Printing
USA(fus)

E
Electronic message center .........18
Emergencies, roadside
jump-starting ..........................266
running out of fuel .........265, 313
Emission control system ..........318
Engine ........................................338
cleaning ...................................281
coolant .....................................301
fail-safe cooling .......................306
idle speed control ...................299
lubrication specifications .......334
refill capacities ........................334
service points ..................290–292
starting after a collision .........250
Engine block heater .................212
Engine oil ..................................294
checking and adding ..............294
dipstick ....................................294
filter, specifications ........298, 333
recommendations ...................298
refill capacities ........................334
specifications ..........................334
Event data recording ....................7
Exhaust fumes ..........................212
F
Fail safe cooling ........................306
Fleet MyKey programming ........96
Flexible Fuel Vehicle (FFV) ....307
Floor mats ...................................94
Fluid capacities .........................334
Fog lamps ....................................55
Four-Wheel Drive vehicles
driving off road .......................242
Fuel ............................................307calculating fuel
economy ............................21, 315
cap ...........................................310
capacity ...................................334
choosing the right fuel ...........311
detergent in fuel .....................313
filler funnel .............................313
filling your vehicle
with fuel ..................307, 310, 315
filter, specifications ........307, 333
fuel pump shut-off ..................251
fuel pump shut-off switch .....250
improving fuel economy ........315
octane rating ...................312, 338
quality ......................................312
running out of fuel .........265, 313
safety information relating
to automotive fuels ................307
Fuel - flex fuel vehicle
(FFV) .........................307, 311–312
Fuel pump shut-off switch .......250
Fuses ..........................................252
G
Garage door opener ....................88
Gas cap (see Fuel cap) ............310
Gas mileage (see Fuel
economy) ...................................315
Gauges .........................................17
H
Hazard flashers .........................250
Headlamps ...................................54
aiming ........................................57
autolamp system .......................54
bulb specifications ....................60
daytime running lights .............56
flash to pass ..............................56
Index
370
2011 Fusion(fsn)
Owners Guide, 3rd Printing
USA(fus)