2011 FIAT FREEMONT technical specifications

5. Grasp the latch plate and pull out the seat belt.
6. Slide the latch plate up the webbing as far as neces-sary to allow the seat belt to go around the child's
lap.
NOTE: The lap portion of the seat belt should be low
on the hips and as snug as possible.
7. Once the seat belt is long enough to fit properly, insert the latch plate into the buckle until you hear
a “click.” (fig. 123)
8. To remove the slack from the lap belt, pull upward on the shoulder portion of the seat belt.
9. To release the seat belt, push the red button on the buckle.
WARNING!
Be certain that the seat cushion is
locked securely into position before us-
ing the seat . Otherwise, the seat will not provide
the proper stability for child seats and/or passen-
gers. An improperly latched seat cushion could
cause serious injury.
Children Too Large For Booster Seats
Children who are large enough to wear the shoulder
belt comfortably and whose legs are long enough to
bend over the front of the seat when their back is
against the seatback should use the lap/shoulder belt in
a rear seat.
• Make sure that the child is upright in the seat.
• The lap portion should be low on the hips and as snug as possible.
• Check belt fit periodically. A child's squirming or slouching can move the belt out of position.
• If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never
allow a child to put the shoulder belt under an arm or
behind their back.
(fig. 123) 145
KNOWING
YOURVEHICLESAFETYSTARTING ANDDRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

WARNING!
 Improper installation can lead to fail-
ure of an infant or child restraint . It
could come loose in a collision.The child could be
badly injured or killed. Follow the manufacturer's
directions exactly when installing an infant or
child restraint .
 A rearward-facing child restraint should only
be used in a rear seat . A rearward-facing child
restraint in the front seat may be struck by a
deploying passenger air bag, which may cause
severe or fatal injury to the infant .
Here are some tips on getting the most out of
your child restraint:
• Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety
Standards. FIAT also recommends that you make
sure that you can install the child restraint in the
vehicle where you will use it before you buy it.
• The restraint must be appropriate for your child's weight and height. Check the label on the restraint
for weight and height limits.
• Carefully follow the instructions that come with the restraint. If you install the restraint improperly, it may
not work when you need it.
• Buckle the child into the seat according to the child restraint manufacturer's directions.
WARNING!
When your child restraint is not in use,
secure it in the vehicle with the seat belt
or remove it from the vehicle. Do not leave it
loose in the vehicle. In a sudden stop or accident ,
it could strike the occupants or seatbacks and
cause serious personal injury.
ISOFIX — Child Seat Anchorage System
Your vehicle's second row passenger seats are
equipped with the child restraint anchorage system
called ISOFIX. The ISOFIX system provides for the
installation of the child restraint without using the
vehicle's seat belts, instead securing the child restraint
using lower anchorages and upper tether straps from
the child restraint to the vehicle structure.
ISOFIX-compatible child restraint systems are now
available. However, because the lower anchorages are
to be introduced over a period of years, child restraint
systems having attachments for those anchorages will
continue to have features for installation using the
vehicle's seat belts. Child restraints having tether straps
and hooks for connection to the top tether anchorages
have been available for some time. For some older child
restraints, many child restraint manufacturers offer
add-on tether strap kits or retrofit kits. You are urged
to take advantage of all the available attachments pro-
vided with your child restraint in any vehicle.
146
KNOWING YOUR
VEHICLESAFETYSTARTING AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

All three second-row passenger seating positions have
lower anchorages that are capable of accommodating
ISOFIX-compatible child seats. You should never install
ISOFIX-compatible child seats so that two seats share
a common lower anchorage. If installing child seats in
adjacent seating positions, or if your child restraints are
not ISOFIX-compatible, install the restraints using the
vehicle's seat belts. (fig. 124)
(fig. 124)ISOFIX Anchorages
1 — Outer 60% Seating Position. Use Lower Anchor
Loops A and B. If placing a second child seat in the
vehicle, use the Outer 40% Seating Position and Lower
Anchor Loops D and E. DO NOT USE Middle 60%
Seating Position and Lower Anchorage Loops B and C.
2 — Middle 60% Seating Position. Use Lower Anchor
Loops B and C. If placing a second child seat in the
vehicle, use the Outer 40% Seating Position and Lower
Anchor Loops D and E. DO NOT USE Outer 60%
Seating Position and Lower Anchor Loops A and B.
3 — Outer 40% Seating Position. Use Lower Anchor
Loops D and E. If placing a second child seat in the
vehicle, use Outer 60% Seating Position and Lower
Anchor Loops A and B or Middle 60% Seating Position
and Lower Anchor Loops B and C.
147
KNOWING
YOURVEHICLESAFETYSTARTING ANDDRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

Vehicle ISOFIX Positions Chart
Mass Group Size
Class Fixture Front
Passenger Rear
Outboard Rear
Center Intermediate
Outboard
Right / Left Intermediate
Center Other Sites
Carrycot F ISO/L1 X X X **IUF / X **IUF X
G ISO/L2 X X X X / **IUF X X (1) X X X X X X
0 — up to 10 kg E ISO/R1 X X X *IUF / *IUF *IUF X
(1) X X X X X X
0+ — up to 13 kg E ISO/R1 X X X *IUF / *IUF *IUF X
D ISO/R2 X X X *IUF / *IUF *IUF X C ISO/R3 X X X *IUF / *IUF *IUF X (1) X X X X X X
I – 9 to 18 kg D ISO/R2 X X X *IUF / *IUF *IUF X
C ISO/R3 X X X *IUF / *IUF *IUF X B ISO/F2 X X X IUF / IUF IUF X
B1 ISO/F2X X X X IUF / IUF IUF X
A ISO/F3 X X X IUF / IUF IUF X (1) X X X X X X
II – 15 to 25 kg (1) X X X X X X III – 22 to36 kg (1) X X X X X X
Key of letters used in the table above:
(1) = For the CRS which do not carry the ISO/XX size
class identification (A to G), for the applicable mass
group, the car manufacturer shall indicate the vehicle specific ISOFIX child restraint system(s) recommended
for each position.
IUF = Suitable for ISOFIX forward child restraints
systems of universal category approved for use in the
mass group.
148
KNOWING
YOUR
VEHICLESAFETYSTARTING AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

IL = Suitable for particular ISOFIX child restraint sys-
tems (CRS) given in the attached list. These ISOFIX
CRS are those of the “specific vehicle”, “restricted” or
“semi-universal” catagories.
X = ISOFIX position not suitable for ISOFIX child
restraint systems in this mass group and / or this sizeclass.
* = Seats in front of child restraint seats may need to be
adjusted forward to install the child restraint seat.
** = No access to 3rd row seating positions if Carrycot
is installed in vehicle.
Installing The ISOFIX-Compatible Child
Restraint System
We urge you to follow the manufacturer's directions
carefully when installing your child restraint. Not all
child restraint systems will be installed as described
here. Again, carefully follow the installation instruc-
tions that are provided with the child restraint system.
NOTE:When installing a child restraint, if it inter-
feres with the Head Restraint, recline the seatback
slightly to remove the interference.
The lower anchorages are round bars located
at the rear of the seat cushion where it meets
the seatback and are just visible when you
lean into the rear seat to install the child
restraint. You will easily feel them if you run your finger
along the intersection of the seatback and seat cushion
surfaces. (fig. 125) In addition, there are tether strap anchorages located
behind each rear seatback, near to the floor. (fig. 126)
(fig. 125)
ISOFIX Anchorages(fig. 126)Tether Strap Anchors 149
KNOWING
YOURVEHICLESAFETYSTARTING ANDDRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

Many, but not all, restraint systems will be equipped
with separate straps on each side, with each having a
hook or connector for attachment to the lower an-
chorage and a means of adjusting the tension in the
strap. Forward-facing toddler restraints and some rear-
facing infant restraints will also be equipped with a
tether strap, a hook for attachment to the tether strap
anchorage and a means of adjusting the tension of the
strap.
You will first loosen the child seat adjusters on the
lower straps and on the tether strap so that you can
more easily attach the hooks or connectors to the
vehicle anchorages. Next, attach the lower hooks or
connectors over the top of the seatcover material.
Then attach the tether strap to the anchorage directly
behind the seat where you are placing the child re-
straint, being careful to route the tether strap to
provide the most direct path between the anchor and
the child restraint, preferably between the head re-
straint posts underneath the head restraint. For center
seating position, adjust the head restraint to the up-
ward position and route the tether strap between the
head restraint posts underneath the head restraint.
Then, attach the hook to the tether anchor located on
the back of the seat. Finally, tighten all three straps as
you push the child restraint rearward and downward
into the seat, removing slack in the straps according to
the child restraint manufacturer's instructions.NOTE:
• Ensure that the tether strap does not slip into the
opening between the seatbacks as you remove slack in
the strap.
• When using the ISOFIX attaching system to install a
child restraint, please ensure that all seat belts not
being used for occupant restraints are stowed and out
of reach of children. Remind all children in the vehicle
that the seat belts are not toys and that they should not
play with them. In addition, never leave unattended
children in the vehicle.
WARNING!
Improper installation of a child restraint
to the ISOFIX anchorages can lead to
failure of an infant or child restraint . The child
could be badly injured or killed. Follow the manu-
facturer's directions exactly when installing an
infant or child restraint .
150
KNOWING YOUR
VEHICLESAFETYSTARTING AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

Installing Child Restraints Using The Vehicle
Seat Belt
The seat belts in the passenger seating positions are
equipped with an Automatic Locking Retractor (ALR)
or a cinching latch plate to secure a Child Restraint
System (CRS). These types of seat belts are designed to
keep the lap portion of the seat belt tight around the
child restraint so that it is not necessary to use a
locking clip. The ALR will make a ratcheting noise if you
extract the entire belt from the retractor and then
allow the belt to retract into the retractor. For addi-
tional information on ALR, refer to “Automatic Locking
Mode” description under “Seat Belts in Passenger Seat-
ing Positions” section. The chart below defines the
seating positions with an Automatic Locking Retractor
(ALR) or a cinching latch plate.
Driver Center Passenger
CRS Lock CRS Lock CRS Lock
First Row N/A N/A ALR
Second Row ALR ALR ALR
• N/A — Not Applicable
• ALR — Automatic Locking Retractor
Installing a Child Restraint with a Cinching Latch Plate:
1. To install a child restraint with a cinching latch plate,
first, pull enough of the seat belt webbing from the
retractor to route it through the belt path of the
child. Slide the latch plate into the buckle until you
hear a “click.” 2. Finally, pull on any excess webbing to tighten the lap
portion around the child restraint. Any seat belt
system will loosen with time, so check the belt
occasionally, and pull it tight if necessary.
Installing a Child Restraint with an ALR:
1. To install a child restraint with ALR, first, pull enough of the seat belt webbing from the retractor
to route it through the belt path of the child re-
straint. Slide the latch plate into the buckle until you
hear a “click.” Next, extract all the seat belt webbing
out of the retractor and then allow the belt to
retract into the retractor. As the belt retracts, you
will hear a ratcheting sound. This indicates the
safety belt is now in the Automatic Locking mode.
2. Finally, pull on any excess webbing to tighten the lap portion around the child restraint. Any seat belt
system will loosen with time, so check the belt
occasionally, and pull it tight if necessary.
NOTE: When installing a child restraint, if it inter-
feres with the Head Restraint, recline the seatback
slightly to remove the interference.
151
KNOWING
YOURVEHICLESAFETYSTARTING ANDDRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

To attach a child restraint tether strap:
• Route the tether strap to provide the most direct
path for the strap between the anchor and the child
seat, preferably between the head restraint posts un-
derneath the head restraint. For center seating posi-
tion, adjust the head restraint to the upward position
and route the tether strap between the head restraint
posts underneath the head restraint. Then, attach the
hook to the tether anchor located on the back of the
seat. (fig. 127)
• If necessary, move the seat forward to provide better
access to the tether anchor. (fig. 128)
• Attach the tether strap hook of the child restraint to
the tether anchor and remove slack in the tether strap
according to the child restraint manufacturer's instruc-tions.NOTE:
Ensure that the tether strap does not slip into
the opening between the seatbacks as you remove
slack in the strap.
WARNING!
 Child Restraint Anchorages are de-
signed to withstand only those loads im-
posed by correctly-fitted child restraints. Under
no circumstances are they to be used for adult
seat belts, harnesses or for attaching other items
or equipment to the vehicle.
 An incorrectly anchored tether strap could lead
to increased head motion and possible injury to
the child. Use only the anchor positions directly
behind the child seat to secure a child restraint
top tether strap.
(fig. 127) Tether Strap Mounting
(fig. 128)Seat Track Release Lever
152
KNOWING
YOUR
VEHICLESAFETYSTARTING AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS