2011 DODGE DURANGO key

NOTE:When shifting out of transfer case NEUTRAL,
turning the engine OFF may be required to avoid gear
clash.
9. Shift transmission into PARK.
10. Release the brake pedal.
11. Disconnect vehicle from the tow vehicle.
12. Start the engine.
13. Press and hold the brake pedal.
14. Release the parking brake.
15. Shift the transmission into gear, and check that the
vehicle operates normally.
16. The Keyless Enter-N-Go button (if equipped) may
now be reinstalled if desired. Refer to “Starting
Procedures/Keyless Enter-N-Go” in “Starting and Oper-
ating” for further information. NOTE:
•Steps 1 through 5 are requirements that must be met
prior to pressing the transfer case NEUTRAL button
and must continue to be met until the shift has been
completed. If any of these requirements are not met
prior to pressing the NEUTRAL button, or are no
longer met during the shift, the NEUTRAL indicator
light will flash continuously until all requirements are
met or until the NEUTRAL button is released.
•The ignition switch must be in the ON/RUN position
for a transfer case shift to take place and for the
position indicator lights to be operable. If the ignition
switch is not in the ON/RUN position, the shift will
not take place and no position indicator lights will be
on or flashing.
•A flashing NEUTRAL position indicator light indicates
that shift requirements have not been met.
446 STARTING AND OPERATING

WHAT TO DO IN EMERGENCIES
CONTENTS
Hazard Warning Flashers ................ 448
 If Your Engine Overheats ................ 448
 Jacking And Tire Changing ............... 449
▫ Jack Location ....................... 450
▫ Spare Tire Stowage ................... 451
▫ Spare Tire Removal ................... 452
▫ Preparations For Jacking ............... 455
▫ Jacking Instructions ................... 455 
Jump-Starting ........................ 463
▫ Preparations For Jump-Start ............. 464
▫ Jump-Starting Procedure ............... 465
 Emergency Tow Hooks — If Equipped ...... 467
 Shift Lever Override ................... 468
 Towing A Disabled Vehicle ............... 469
▫ Towing Without The Ignition Key FOB ..... 471
▫ Rear-Wheel Drive Models .............. 471
▫ All-Wheel Drive Vehicles ............... 472
6

CAUTION!
•Do not attempt to use sling type equipment when
towing. When securing the vehicle to a flat bed
truck, do not attach to front or rear suspension
components. Damage to your vehicle may result
from improper towing.
•If the vehicle being towed requires steering, the
ignition must be in the ON/RUN or ACC position,
not in the LOCK position.
Towing Without The Ignition Key Fob
Special care must be taken when the vehicle is towed
with the ignition in the LOCK position. The only ap-
proved method of towing without the ignition key is
with a flatbed truck. Proper towing equipment is neces-
sary to prevent damage to the vehicle.
Rear-Wheel Drive Models
The manufacturer recommends towing your vehicle with
all four wheelsOFFthe ground using a flatbed.
If flatbed equipment is not available, and the transmis-
sion is operable, the vehicle may be towed (with rear
wheels on the ground) with the transmission in NEU-
TRAL. Speed must not exceed 30 mph (48 km/h) and the
distance must not exceed 15 miles (24 km).
CAUTION!
Towing faster than 30 mph (48 km/h) or farther than
15 miles (24 km) with rear wheels on the ground can
cause severe damage to the transmission. Such dam-
age is not covered by the New Vehicle Limited
Warranty.6
WHAT TO DO IN EMERGENCIES 471

the SELECT button to turn off the message. If the
problem continues, the message will appear the next time
the vehicle is started.
A loose, improperly installed, or damaged fuel filler cap
may also turn on the Malfunction Indicator Light (MIL).
EMISSIONS INSPECTION AND MAINTENANCE
PROGRAMS
In some localities, it may be a legal requirement to pass
an inspection of your vehicle’s emissions control system.
Failure to pass could prevent vehicle registration.For states that require an Inspection and Mainte-
nance (I/M), this check verifies the “Malfunction
Indicator Light (MIL)” is functioning and is not
on when the engine is running, and that the OBD II
system is ready for testing. Normally, the OBD II system will be ready. The OBD II
system may
notbe ready if your vehicle was recently
serviced, recently had a dead battery or a battery replace-
ment. If the OBD II system should be determined not
ready for the I/M test, your vehicle may fail the test.
Your vehicle has a simple ignition key-actuated test,
which you can use prior to going to the test station. To
check if your vehicle’s OBD II system is ready, you must
do the following:
1. Turn the ignition switch to the ON position, but do not
crank or start the engine.
2. If you crank or start the engine, you will have to start
this test over.
3. As soon as you turn the ignition switch to the ON
position, you will see the MIL symbol come on as part of
a normal bulb check.
478 MAINTAINING YOUR VEHICLE

Cavity CartridgeFuseMini
Fuse Description
M16 10 Amp
Red Occupant Restraint
Controller
M19 25 Amp
Natural Automatic Shutdown
1 and 2
M20 15 Amp
Blue Instrument Cluster
M21 20 Amp
Yellow Automatic Shutdown
3
M22 10 Amp
Red Horns (Low/High) –
Right
M23 10 Amp
Red Horns (Low/High) –
Left
M24 25 Amp
Natural Rear Wiper
M25 20 Amp
Yellow Fuel Pump Motor
Output/Diesel Lift
Pump (Export Only)Cavity Cartridge
FuseMini
Fuse Description
M26 10 Amp
Red Driver Door Switch
Bank
M27 10 Amp
Red Ignition Switch/
Wireless Control
Module/Keyless En-
try Module
M28 15 Amp
Blue Powertrain
Controller/
Transmission Control-
ler
M29 10 Amp
Red Tire Pressure Monitor
M30 15 Amp
Blue J1962 Diag Connector
M31 20 Amp
Yellow Backup Lamps
7
MAINTAINING YOUR VEHICLE 515

Exterior LightsBulb Type
Headlamp – High Intensity Discharge
(HID) ............ Ser vice at Authorized Dealer (**)
Headlamp (Low Beam) .................... H11
Headlamp (High Beam) ................... 9005
Front Park/Turn Lamp .................7444NA
Front Fog Lamps ..................... PSX24W
Front Side Marker ...................... W5W
Rear Turn/Stop/Tail Lamps ................3057
Liftgate Tail Lamps ....................... 194
Backup Lamps .................... 921 (W16W)
Rear License Lamps ..................... W5W
Center High-Mounted Stop Lamp
(CHMSL) ........................... LED(*)
* CHMSL is not serviceable. It is a LED lamp. To replace
the LED, the entire CHMSL assembly must be replaced.
** The headlamps are a type of high-voltage discharge
tube. High voltage can maintain in the circuit even with
the headlamp switch off and the key fob removed.
Because of this, you should not attempt to service a headlamp bulb yourself. If a headlamp bulb fails, take
your vehicle to an authorized dealer for service.
NOTE:
Numbers refer to commercial bulb types that
can be purchased from your authorized dealer.
If a bulb needs to be replaced, visit your authorized
dealer or refer to the applicable Service Manual.
BULB REPLACEMENT
High Intensity Discharge Headlamps (HID) –
If Equipped
The headlamps are a type of high voltage discharge tube.
High voltage can remain in the circuit even with the
headlamp switch off and the key removed. Because of
this, you should not attempt to service a headlamp bulb
yourself. If a headlamp bulb fails, take your vehicle to
an authorized dealer for service.
518 MAINTAINING YOUR VEHICLE

CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean the
bulb with rubbing alcohol.
Front Fog Lamps
1. Reach through the cutout in the splash shield and
disconnect the wiring harness from the fog lamp connec-
tor.
2. Firmly grasp the bulb by the two latches and squeeze
them together to unlock the bulb from the back of the
front fog lamp housing.3. Pull the bulb straight out from the keyed opening in
the housing.
CAUTION!
•Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If
the bulb comes in contact with any oily surface,
clean the bulb with rubbing alcohol.
•Always use the correct bulb size and type for
replacement. An incorrect bulb size or type may
overheat and cause damage to the lamp, the socket
or the lamp wiring.
520 MAINTAINING YOUR VEHICLE

Special Additives..................... 504
Torque Converter .................... 349
Autostick ............................. 345
Auxiliary Electrical Outlet (Power Outlet) ...... 216
Auxiliary Power Outlet ................... 216
B-Pillar Location ........................ 383
Battery ............................... 485
Keyless Transmitter Replacement (RKE) ..... 27
Belts, Seat ............................ 52,98
Blind Spot Monitoring .................... 111
Body Mechanism Lubrication ............... 488
Brake Assist System ...................... 369
Brake Control System, Electronic ............. 368
Brake Fluid ............................ 500
Brake System ........................... 499
Anti-Lock (ABS) ..................... 368
Fluid Check ........................ 500
Master Cylinder ..................... 500 Parking
........................... 365
Warning Light ....................... 250
Brake/Transmission Interlock ............... 343
Break-In Recommendations, New Vehicle ........ 95
Bulb Replacement ..................... 517,518
Bulbs, Light ............................ 100
Calibration, Compass ..................... 273
Camera, Rear ........................... 202
Capacities, Fluid ........................ 524
Caps, Filler Fuel .............................. 418
Power Steering ...................... 364
Radiator (Coolant Pressure) ............. 497
Car Washes ............................ 507
Carbon Monoxide Warning ...............97,414
Cargo (Vehicle Loading) ................... 422
Cargo Area Cover ....................... 226
Cargo Area Features ...................... 225
10
INDEX 555