2011 Citroen DS3 display
[x] Cancel search: displayPage 109 of 324
107Visibility
Model without AUTO lighting
Model with AUTO lighting
Manual controls
The lighting commands are issued directly by
the driver by means of the ring A
and the stalk B
.
Automatic illumination of headlamps.
B.
Stalk for switching the headlamp beam:
pull the stalk to switch between dipped and
main beam headlamps.
In the lamps off and sidelamps modes, the
driver can switch on the main beam headlamps
temporarily ("headlamp flash") by maintaining a
pull on the stalk.
A.
Main lighting mode selection ring: turn it
to position the symbol required facing the
mark.
Lamps off.
Sidelamps only.
Dipped headlamps or main beam
headlamps.
Displays
Lighting of the corresponding indicator lamp on
the instrument panel confirms the switching on
of the lighting selected.
The instrument panel has permanent back-
lighting. Illumination of the instrument panel is
therefore not linked to the exterior lighting.
Page 112 of 324
The sidelamps and dipped beam headlamps
are switched on automatically, without any
action on the par t of the driver, when a low level
of external light is detected or in cer tain cases
of activation of the windscreen wipers.
As soon as the brightness returns to a
sufficient level or after the windscreen wipers
are switched off, the lamps are switched off
automatically.
Automatic illumination of
headlamps
Activation
)
Turn ring A
to the "AU TO "
position. The
automatic illumination of headlamps
is accompanied by a message in the
multifunction screen.
Deactivation
)
Turn ring A
to a position other than
"AU TO "
. Deactivation is accompanied by a
message in the multifunction screen.
Coupling with the automatic
"Guide-me-home" lighting
Association with the automatic illumination of
headlamps provides "guide-me-home" lighting
with the following additional options:
- selection of the lighting duration to
15, 30 or 60 seconds in the vehicle
parameters in the multifunction screen
configuration menu (except in the case of
the monochrome screen A, for which the
duration is set: 60 seconds),
- automatic activation of "guide-me-home"
lighting when automatic illumination of
headlamps is in operation.
Operating fault
In the event of a fault with the
sunshine sensor, the lighting
come on, this warning lamp is displayed in the
instrument panel and/or a message appears in
the multifunction screen, accompanied by an
audible signal.
Contact a CITROËN dealer or a qualified
workshop.
In fog or snow, the sunshine sensor
may detect sufficient light. Therefore,
the lighting will not come on
automatically.
Do not cover the sunshine sensor,
coupled with the rain sensor and
located in the centre of the windscreen
behind the rear view mirror; the
associated functions would no longer
be controlled.
Page 124 of 324
Auxiliary socket
The auxiliary socket is located in the " AUX "
box on the centre console.
It permits the connection of a por table device,
such as a digital audio player of the iPod
® type,
to listen to your music files using the vehicle's
speakers.
USB Player
For more information on the use of this
equipment, refer to the MyWay or Audio system
part of the "Audio and Telematics" section.
When it is in use, the por table device
charges automatically.
The USB por t is located in the "AU X "
box on
the centre console.
It permits the connection of a por table device,
such as a digital audio player of the iPod
®
generation 5 and later type or USB memory
stick type.
It reads the audio file formats (mp3, ogg,
wma, wav...) which are transmitted to your
audio equipment and played via the vehicle's
speakers.
You can manage these files using the steering
mounted controls or the audio equipment
control panel and display them on the
multifunction screen.
For more information on the use of this
equipment, refer to the Audio system par t of the
"Audio and Telematics" section.
12 V accessory
socket
)
To connect a 12 V accessory (max power:
120 W), lift the cover and connect a
suitable adaptor. The management of the files is done
using your portable device.
Page 162 of 324
Displays in the instrument panel
Gear lever positions
N
. Neutral.
R
. Reverse.
1 2 3 4 5.
Gears engaged.
AUTO.
This comes on when the automated
mode is selected. It switches off on
changing to sequential mode.
7
In the automated mode, if the gearbox
detects poor grip, this warning lamp comes on.
)
Place your foot on the brake
when this warning lamp flashes
(e.g.: starting the engine).
There is an audible signal on
engagement of reverse.
Moving off
)
Select position N
.
)
Press the brake pedal firmly.
)
Star t the engine.
N
appears in the instrument panel.
N
flashes in the instrument panel
screen if the gear lever is not in position
N
on star ting.
)
Select first gear (position M
or A
) or
reverse (position R
)
)
Release the parking brake.
)
Take your foot off the brake pedal, then
accelerate.
AUTO
and 1
or R
appear in the
instrument panel.
Stopping - Moving off on a slope
When stopping on a slope, do not use the
accelerator to immobilise the vehicle; apply the
parking brake.
When moving off on a slope, accelerate
gradually while releasing the parking brake.
Sequential mode
)
After star ting the vehicle, select position M
to change to sequential mode.
AUTO
disappears and the gears
engaged appear in succession in the
instrument panel.
The gear change requests are only carried out
if the engine speed permits.
When driving at low speed, on approaching
a stop sign or traffic lights for example,
the gearbox changes down to first gear
automatically.
Automated mode
)
Following use of the sequential mode,
select position A
to return to the automated
mode.
AUTO
and the gear engaged appear
in the instrument panel.
The gearbox then operates in auto-adaptive
mode, without any action on the par t of the
driver. It continuously selects the most suitable
gear in relation to the following parameters:
- driving style,
- road conditions,
- vehicle load.
Page 163 of 324
161Driving
If you press the accelerator pedal
beyond the point of resistance, the
gearbox selects the gear below to
permit sharper acceleration.
You must press the brake pedal while
star ting the engine.
Never select neutral N
while the vehicle
is moving.
Only engage reverse gear R
when the
vehicle is immobilised, with your foot on
the brake pedal.
In all cases, you must apply the parking
brake to immobilise the vehicle.
"Auto sequential" mode
In the automated mode, you can resume
control temporarily at any time using the
steering mounted control paddles.
The use of these paddles permits manual
selection of the gears in situations which
require a more rapid change-down than in
the automated mode (arrival at a roundabout,
leaving a car park with a steep gradient,
over taking...).
The gearbox engages the required gear if
the engine speed permits. AUTO
remains
displayed in the instrument panel.
After a few minutes, the gearbox resumes
automatic control of the gears.
Stopping the vehicle
Before switching off the engine, you can
change to position N
to be in neutral.
In this case, you must apply the parking brake
to immobilise the vehicle.
Reinitialisation
Following disconnection of the battery, the
gearbox must be reinitialised.
)
Switch on the ignition.
AUTO
and -
appear in the instrument
panel.
)
Select position N
.
)
Press the brake pedal.
)
Wait approximately 30 seconds until N
or a
gear appears in the instrument panel.
)
Release the brake pedal.
The gearbox is operational again.
Operating fault
With the ignition on, if this warning
lamp comes on and AUTO
flashes,
accompanied by an audible signal and a
message in the multifunction screen, this
indicates a gearbox fault.
Have it checked by a CITROËN dealer or a
qualified workshop.
Page 165 of 324
163Driving
When you move the lever in the gate to select
a position, the corresponding indicator is
displayed in the instrument panel.
P.
Park
R.
Reverse
N.
Neutral
D.
Drive (Automatic driving)
S.
Sport
programme
7
.
Snow
programme
1 2 3 4
.
Gears engaged during manual operation
-.
Invalid value during manual operation
Displays in the instrument panel
Foot on brake
)
Press the brake pedal when this
indicator lamp is displayed in the
instrument panel (e.g.: starting
the engine).
Moving off
If position N
is engaged inadvertently
while driving, allow the engine to
return to idle then engage position D
to
accelerate. When the engine is running at idle, with
the brakes released, if position R
, D
or
M
is selected, the vehicle moves even
without the accelerator being pressed.
When the engine is running, never
leave children in the vehicle without
supervision.
When carrying out maintenance with
the engine running, apply the parking
brake and select position P
.
)
Apply the parking brake.
)
Select position P
or N
.
)
Star t the engine.
If this procedure is not followed, an audible
signal is heard, accompanied by a message in
the multifunction screen.
)
With the engine running, press the brake
pedal.
)
Release the parking brake.
)
Select position R
, D
or M
.
)
Gradually release the brake pedal.
The vehicle moves off immediately.
Page 167 of 324
165Driving
Manual operation
D
disappears and the gears engaged
appear in succession on the
instrument panel.
If the engine speed is too low or
too high, the gear selected flashes for a few
seconds, then the actual gear engaged is
displayed.
It is possible to change from position D
(automatic) to position M
(manual) at any time.
When the vehicle is stationary or moving
very slowly, the gearbox selects gear M1
automatically.
The spor t and snow programmes do not
operate in manual mode.
Invalid value during manual
operation
)
Select position M
for sequential
changing
of the four gears.
)
Push the lever towards the +
sign to
change up a gear.
)
Pull the lever towards the -
sign to change
down a gear.
It is only possible to change from one gear to
another if the vehicle speed and engine speed
permit; other wise, the gearbox will operate
temporarily in automatic mode. This symbol is displayed if a gear
is not engaged correctly (selector
between two positions).
Stopping the vehicle
Before switching off the engine, you can engage
position P
or N
to place the gearbox in neutral.
In both cases, apply the parking brake to
immobilise the vehicle. When the ignition is on, the lighting
of this warning lamp, accompanied
by an audible signal and a message in the
multifunction screen, indicates a gearbox fault.
In this case, the gearbox switches to back-up
mode and is locked in 3rd gear. You may feel
a substantial knock when changing from P
to R
and from N
to R
. This will not cause any
damage to the gearbox.
Do not exceed 60 mph (100 km/h), local speed
restrictions permitting.
Contact a CITROËN dealer or a qualified
workshop as soon as possible.
Operating fault
If the lever is not in position P
,
when the driver's door is opened or
approximately 45 seconds after the
ignition is switched off, a message
appears in the multifunction screen.
)
Return the lever to position P
; the
message disappears.
There is a risk of damage to the
gearbox:
- if you press the accelerator and
brake pedals at the same time,
- if you force the movement of the
gear lever from the P
position to
another position when the battery
is flat.
To reduce fuel consumption when at
a prolonged standstill with the engine
running (traffic jam...), put the gear lever in
the N
position and apply the parking brake.
Page 169 of 324
167Driving
Going into engine START mode
The "ECO"
warning lamp goes off
and the engine star ts:
- with a manual gearbox
, when you fully
depress the clutch pedal.
Special cases: START invoked
automatically
If the system has been deactivated
in STOP mode, the engine restarts
immediately. At any time, press the "ECO OFF"
switch to
deactivate the system.
This is confirmed by the switch warning lamp
coming on accompanied by a message in the
screen.
Deactivation
For your safety and comfort, START mode is
invoked automatically when:
- you open the driver's door ,
- you unfasten the driver's seat belt,
- the speed of the vehicle exceeds 15 mph
(25 km/h) with a manual gearbox,
- some special conditions (battery charge,
engine temperature, braking assistance,
ambient temperature...) where the engine is
needed to assure control of a system.
The "ECO"
warning lamp flashes, then
goes off.
This operation is per fectly normal.
With a manual gearbox in STOP mode,
if a gear is engaged without fully
depressing the clutch pedal, a message
is displayed asking you to depress the
clutch pedal to restar t the engine.