2011 CITROEN C4 PICASSO lock
[x] Cancel search: lockPage 161 of 352
Downloaded from www.Manualslib.com manuals search engine IX
159
DRIVING
Manual operation
Position of the gear lever for manual
gear changing.
)
Move the gear lever to
position M
.
)
Pull the " +
" paddle to change up
a gear.
)
Pull the " -
" paddle to change
down a gear.
- If the vehicle stops or reduces
speed (for example when ap-
proaching a stop sign), the gear-
box changes down automatically
to fi rst gear.
- In manual mode, it is not neces-
sary to release the accelerator
during gear changes.
- A request to change gear is ac-
cepted only if the engine speed
permits it.
- For safety reasons, depending
on the engine speed, a change
up or down may be performed
automatically.
- It is possible at any time to
change mode, by moving the
gear lever from position D
to po-
sition M
or vice versa.
Flashing of the indicator for
the position requested sig-
nals that this position is not
yet obtained.
If the indicator is on fi xed, the posi-
tion is confi rmed.
Display of a dash in the rev counter
indicates a malfunction. Contact
a CITROËN dealer or a qualifi ed
workshop.
Illumination of the service warning
lamp accompanied by a message
and an audible signal indicates an
operating fault. In this case:
- a marked snatching may be felt
when selecting R
for reverse
gear,
- the gearbox is locked in one
gear,
- do not exceed a speed of 60 mph
(approximately 100 km/h).
Have it checked by a CITROËN
dealer or a qualifi ed workshop.
Page 173 of 352
Downloaded from www.Manualslib.com manuals search engine IX
171
DRIVING
PNEUMATIC SUSPENSION
Grand
C4 Picasso
C4 Picasso
The pneumatic rear suspension en-
hances driving comfort by maintain-
ing a constant body height whatever
the vehicle load.
Operation
- If there is an increase in vehicle
load, a sinking of the rear of
the vehicle is detected and the
pneumatic springs infl ate in or-
der to compensate for the extra
weight.
- If there is a decrease in load, a
rising of the rear of the vehicle is
detected and so the pneumatic
springs defl ate to return the ve-
hicle to its nominal height.
- If the vehicle has been unused
for a long period, the pneumatic
springs may infl ate if necessary
when you unlock or open a door,
so as to return the vehicle to its
nominal height.
If you do not reactivate the system
manually, automatic height correc-
tion will be activated as soon as the
vehicle starts to move. During height
correction, the service warning lamp
comes on and a message on the
screen reminds you not to exceed 6
mph (10 km/h).
The automatic correction does not
function if the doors or the boot are
open.
The automatic correction operates
even if your vehicle is in power
economy mode.
Activation/Deactivation
The automatic height correction can
be deactivated:
)
press button B
located on the
left hand boot interior trim for ap-
proximately two seconds,
)
release the button when you
hear a beep. Deactivation is con-
fi rmed by the lighting of the indi-
cator lamp in button B
.
In the event of a system fault,
alert messages, always in asso-
ciation with the service warning
lamp, will appear in the instru-
ment panel
. Contact a CITROËN
dealer or a
qualifi ed workshop.
You must deactivate the system in
the following circumstances:
- when working under the vehicle,
- when changing a wheel,
- when transporting the vehicle on
a lorry or ferry.
To reactivate automatic height cor-
rection:
)
press button B
again for approxi-
mately two seconds,
)
release the button when you hear
a beep. Activation is confi rmed
by the extinction of the indicator
lamp in button B
.
Page 189 of 352
Downloaded from www.Manualslib.com manuals search engine XI
187
PRACTICAL INFORMATION
Grand C4 Picasso
C4 Picasso
Access to the spare wheel
Taking out the wheel (Grand
C4 Picasso)
)
Lift the boot fl oor covering to re-
veal the spare wheel carrier drive
on the right.
)
Take the extension 8
clipped in
the rear of the well below the
right hand third-row seat.
)
Lift up the spare wheel carrier
drive aperture cap.
)
Fit the extension to the drive then
engage the head of the wheel-
brace 4
on the extension.
)
Turn the assembly clockwise
to
the end of its travel to lower the
spare wheel carrier; the spare
wheel is now resting on the
ground.
)
Pull the wheel towards you and
pass the linking plate through
the centre of the wheel.
With the damaged wheel
now under the vehicle fl oor,
the vehicle has reduced
ground clearance, so take extra
care when reversing or driving on
uneven surfaces, including kerbs.
Retrieval of the spare wheel and
stowage of the affected road wheel
are operations that should be done
with the vehicle standing on its
wheels, not supported by the jack.
Putting the wheel back in place
)
The tyre valve must be facing
upwards.
)
Pass the linking plate through
the centre of the wheel (fi rst re-
moving the central trim on cer-
tain alloy wheels).
)
Turn the carrier drive anti-clock-
wise
to draw in the carrier cable.
Initially the drive will turn freely,
then the cable will tighten to raise
the wheel.
Check that the wheel is tight
against the vehicle fl oor and
not interfering with other nearby
components (e.g. the exhaust).
)
Stow the tools.
Taking out the wheel (C4 Picasso)
)
Lift the boot fl oor covering to re-
veal the spare wheel carrier drive
on the left.
)
Take the extension 7
from the
set of tools.
)
Lift up the spare wheel carrier
drive aperture cap, if fi tted.
)
Fit the extension to the drive then
engage the head of the wheel-
brace 4
on the extension.
)
Turn the assembly clockwise
to
the end of its travel to lower the
spare wheel carrier; the spare
wheel is now resting on the
ground.
)
Pull the wheel towards you and
pass the linking plate through
the centre of the wheel.
Page 193 of 352
Downloaded from www.Manualslib.com manuals search engine XI
191
PRACTICAL INFORMATION
Main beam headlamps
)
Remove the rubber cover.
)
Detach the clips by lowering
them on each side of the bulb.
)
Pull on the bulb-holder to remove it.
)
Replace the faulty bulb.
)
Push the bulb-holder back into
its housing.
)
Reattach the clips.
)
Refi t the rubber cover.
Dual-function Xenon headlamps
(dipped/main beam)
Additional main beam headlamps
)
Remove the rubber cover.
)
Rotate the bulb-holder a quarter
turn anti-clockwise and remove it
from its housing.
)
Replace the faulty bulb.
)
Reposition the bulb-holder by
pushing it in, tightening it by a
quarter turn clockwise.
)
Refi t the rubber cover.
If the headlamp bears this
symbol, any operation to
change the Xenon dual-
function directional head-
lamp (D1S-35 W) must be carried
out by professionals (risk of elec-
trocution).
Contact a CITROËN dealer or a
qualifi ed workshop.
It is recommended to change both
bulbs at the same time if one of
them is faulty.
Dipped beam headlamps
)
Remove the rubber cover.
)
Rotate the bulb-holder a quarter
turn anti-clockwise and remove it
from its housing.
)
Replace the faulty bulb.
)
Reposition the bulb-holder by
pushing it in, tightening it by a
quarter turn clockwise.
)
Refi t the rubber cover.
Page 194 of 352
Downloaded from www.Manualslib.com manuals search engine XI
192
PRACTICAL INFORMATION
Sidelamps
)
Rotate the bulb-holder a quarter
turn anti-clockwise.
)
Remove it from its housing.
)
Replace the faulty bulb.
)
Reposition the bulb-holder.
)
Rotate it a quarter turn clockwise
to reposition in its housing.
Direction indicators
The direction indicator bulb is locat-
ed underneath the main beam bulb.
)
Remove the rubber cover.
)
Pull on the bulb-holder to remove it.
)
Replace the faulty bulb.
)
Reposition the bulb-holder in the
bracket and push it in.
)
Refi t the rubber cover.
Integrated direction indicator
side repeaters
To change the repeater, press down-
wards fi rmly on the zone indicated
by the arrow, then pull the repeater.
Repeaters can be obtained from
a CITROËN dealer or a qualifi ed
workshop.
Page 200 of 352
Downloaded from www.Manualslib.com manuals search engine XI
198
PRACTICAL INFORMATION
Fuses under the dashboard
Access to the fuses
)
Undo the screw by a quarter turn
and pivot the housing.
Table of fuses
Fuse N°
Rating
Functions
F1
15 A
Rear screen wipe
F2
30 A
Locking and unlocking earth
F3
5 A
Airbags and pretensioners
F4
10 A
Multimedia, photochromatic rear view mirror,
particle fi lter, diagnostic socket, air conditioning,
manual headlamp height adjustment
F5
30 A
Front windows, front door electronic control panel,
panoramic sunroof
F6
30 A
Rear windows
F7
5 A
Interior lamps, cooled glovebox, radio
F8
20 A
Multifunction screen, radio, steering mounted
controls, multimedia, under infl ation detection,
alarm, trailer
F9
30 A
Multimedia, front 12 V sockets, torch, radio
F10
15 A
Height corrector (suspension)
F11
15 A
Brake switch, ignition switch
F12
15 A
Parking sensors, automatic wipers and lighting,
passenger’s electric seat, lane departure warning
system, Hi-Fi amplifi er, trailer
F13
5 A
Engine relay unit (BSM), driver’s electric seat
F14
15 A
Air conditioning, Bluetooth ®
hands-free system, automatic
gearbox selector lever, airbags, instrument panel
F15
30 A
Locking and unlocking
F16
-
SHUNT
F17
40 A
Heated rear screen
Page 206 of 352
Downloaded from www.Manualslib.com manuals search engine XI
204
PRACTICAL INFORMATION
Disconnecting the (+)
terminal
)
Raise the lever D
fully to release
the clamp E
.
Do not force the lever as locking
will not be possible if the clamp is
not positioned correctly; start the
procedure again.
Reconnecting the (+) terminal
)
Position the open clamp E
of the
cable on the positive post (+) of
the battery.
)
Press down on the clamp to po-
sition it correctly on the battery
post.
)
Lock the clamp by lowering the
lever D
.
Starting using another
battery
If the battery in your vehicle is fl at,
the engine can be started using a
slave battery (external or in another
vehicle) and jump leads.
First ensure that the slave
battery has a nominal volt-
age of 12 V and a capac-
ity at least equal to that of the fl at
battery.
Do not try to start the engine by
connecting a battery charger.
Do not disconnect the (+) terminal
when the engine is running.
)
Connect the red lead to the (+)
terminal of the fl at battery A
,
then to the (+) terminal of the
slave battery B
.
)
Connect one end of the green or
black lead to the (-) terminal of
the slave battery B
(or the earth
point on the slave vehicle).
)
Connect the other end to the
earth point C
on the broken-
down vehicle.
)
Start the engine on the slave ve-
hicle and leave the engine run-
ning for a few minutes.
)
Operate the starter on the bro-
ken-down vehicle and leave the
engine running.
If the engine does not start
straight away, switch off the ig-
nition and wait a few moments
before trying again.
)
With the engine idling, discon-
nect the jump leads in reverse
order.
Page 207 of 352
Downloaded from www.Manualslib.com manuals search engine XI
205
PRACTICAL INFORMATION
Before disconnecting
)
Go to the battery.
)
Check that all of the openings -
doors, boot... - are closed but not
locked.
)
Wait at least four minutes after
switching off the ignition.
Charging
)
Disconnect the (+) terminal.
)
Follow the instructions on use
provided by the manufacturer of
the charger.
)
Connect the red cable of the
charger to the (+) post of the bat-
tery, then the black cable to the
(-) terminal.
)
Once charging is complete, dis-
connect the charger cables in re-
verse order.
The charging operation
must be carried out in a
well ventilated area and
well away from naked fl ames and
sources of sparks, so as to avoid
any risk of explosion and fi re.
Do not try to charge a frozen bat-
tery; the battery must fi rst be
thawed out to avoid any risk of ex-
plosion. If the battery has frozen,
before charging, have it checked
by a CITROËN dealer or a quali-
fi ed workshop, who will ensure that
the internal components have not
been damaged and that the casing
is not cracked, which would intro-
duce the risk of a leak of toxic and
corrosive acid.
Charging the battery using
a battery charger
If the battery of your vehicle is fl at
or prior to taking the vehicle out of
service for an extended period, you
can charge the battery using a bat-
tery charger.
For information on the specifi cation
of battery chargers compatible with
your battery, refer to a CITROËN
dealer or a qualifi ed workshop.
It is recommended that the battery
be disconnected if the vehicle is not
be used for more than a month.
Reinitialisation after
reconnection
After any reconnection of the bat-
tery, switch on the ignition and wait
at least one minute before starting,
to allow time for the initialisation of
the electronic systems.
By referring to the corresponding
sections, you should set or initialise
the following systems yourself:
- the date and time,
- the anti-pinch on the driver's
electric window and the sunroof.
- the panoramic sunroof blind,
- the multifunction screen set-
tings,
- the audio system or navigation
system settings,
Check that there no error message
or warning lamp comes on after
switching on the ignition.
However, if minor problems persist
after carrying out these operations,
contact a CITROËN dealer or a
qualifi ed workshop.