2011 Citroen C ZERO RHD lock

Access
32
Folding the key
Anti-theft protection
)First press button A
to fold the key.




Electronic engine immobiliser

The key contains an electronic chip which has a
special code. When the ignition is switched on,
this code must be recognised to permit star ting.
This electronic engine immobiliser locks theengine management system a few moments
after the ignition is switched off and prevents
starting of the engine by anyone who does not have the key.
In the event of a malfunction and if your vehicle
does not start, contact a CITROËN dealer as
soon as
possible.

Remote control problem

In the event of a remote control malfunction,
you can neither unlock nor lock your vehicle.)First of all, use the key in the driver's door
lock to unlock or lock your vehicle.
)Then, contact a CITROËN dealer to check
the operation of the remote control and
replace the battery if necessary.

2
!
Access
33
Lost keys
Visit a CITROËN dealer with the vehicle’s V5 registration document and your personalidentification documents.
The CITROËN dealer will be able to retrieve the key code and the transponder coderequired to order a replacement key.
Remote control
The high frequency remote control is a sensitive system; do not operate it while it is in your pocket as there is a possibility that it may unlock the vehicle, without you being aware of it. Do not repeatedly press the buttons of your remote control out of range and out of sight of your vehicle. You run the risk of stopping it from working.The remote control does not operate when the key is in the ignition, even when the ignition is switched off.
Locking the vehicle
Driving with the doors locked may make access to the passenger compar tment bythe emergency services more difficult in an emergency.
As a safety precaution (with children on board), remove the key from the ignition whenyou leave the vehicle, even for a shor t time.
Anti-theft protection
Do not make any modifications to the electronic immobiliser system; this could causemalfunctions.
When purchasing a second-hand vehicle
Have the key codes memorised by a CITROËN dealer, to ensure that the keys in your possession are the only ones which can star t the vehicle.

2
!
Access
35





Doors


From outside
)After unlocking the vehicle using theremote control or the key, pull the door handle.
From inside
)
Pull the front or rear door control to open
the door.
If the doors are locked, opening the driver's door does not unlock the other doors.
- opening the driver's door unlocks the other doors,
- the front passenger or rear doors must
then be unlocked manually using the frontlocking control before they can be opened.
I
f a door or the boot is not closedcorrectly, this warning lamp comes
on in the instrument panel until the
door in question or the boot is closed.

Opening
Closin
g
Locking/unlocking from the
inside
) Press the button on the driver's door
towards the front to lock and towards
the rear to unlock the vehicle completely.
The buttons on the front and rear passenger doors only lock/unlockthe door in question.

Access
36








Boot
Opening
)After unlocking the vehicle using the remote control or the key, press the handle Aand
open the tailgate.
)
Pull the handle B
downwards to guide the
tailgate down,) release the handle and press the exterior surface of the tailgate gently to close it.


Closing

!
Comfort
42





Door mirrors
The mirrors can be adjusted when the ignitionswitch is in the "ON" or "ACC" position. )Move control A
to the right or to the left to
select the corresponding mirror.)Direct control B in all four directions to adjust the mirror.
When adjustment is complete, return control Ato the central position.
Adjustment


The mirrors can also be foldedmanually.
However, you must never unfold them manually, other wise the mirrors may ynot remain in place correctly whendriving.
Always use control C
to unfold them.

)
With the ignition switch in the "ON" or "ACC" position: press control Cto unfold
them ) With the ignition switch in the "LOCK"
position: press control C within
30 secondsto fold them.
Electric folding/unfolding

i
!
Driving
52










Starting - stopping the vehicle
- Position 1: LOCK
The steering is locked.
- Position 2: ACCThe ancillaries (radio, 12 V socket...)can be used.
- Position 3: ONIgnition on.
- Position 4: START"Ready" lamp on.
Motor ready to drive the vehicle.
Ignition switch
) Inser t the key in the ignition switch.
)
Turn the key to position 4 (START).


Starting
Stopping
)Immobilise the vehicle.
)Place the drive selector in position P.P)Turn the key to position 1 (LOCK).)Remove the key from the ignition switch.)Hold it in this position for a few seconds until the "READY" lamp comes on accompanied by an
audible signal.
) Release the key.
The key returns automaticallyto position 3 (ON).
Key in ignition
If the key has been left in the ignition, an
audible signal is heard on opening the driver's door.

Do not attach any heavy objects to the key as this could weigh down on it whenin the ignition switch and cause a fault.

If you use the ancillaries for a prolonged period (with the key in the ACCposition), you risk discharging theancillaries battery. Star ting your vehiclewill then no longer be possible.Be aware .

i
i
i
Visibility
58
Daytime running lamps
Special daytime lighting so that the vehicle can
be seen more easily. The daytime running lamps come on automatically when star ting the motor, if no
other lighting is on.
They cannot be deactivated. With the main li
ghting control ring in the AUTO
position, the sidelamps and dipped beam
headlamps come on automaticall
y, without anyaction by the driver, when a low level of ambientlight is detected.
When the light returns to a sufficient level or the
wipers are switched off, the lighting is switched
off automatically.
The sensor is located at the base of the
windscreen.
Automatic illumination of headlamps
Automatic lighting off
When the lighting stalk is in the "dipped or mainbeam headlamps" position, if the ignition switch
is in the "LOCK" or "ACC" position or if thekey has been removed, the lighting switches
off automatically when the driver's door isopened .
The driver is is aler ted by an audible signal. The initial setting is position "0".









Headlamp
adjustment

To avoid causing a nuisance to other road
users, the height of the halogen headlampsshould be adjusted according to the load in the
vehicle. 0. Driver only or driver + 1 front passenger.
1 or 2.
4 people (including the driver). 3.4 people (including the driver) + maximumauthorised load.4.
Driver + maximum authorised load.

Even though these lamps are located inthe same lamp unit as the front foglamp, the operate with a specific bulb.
Their use is covered by road vehiclelighting regulations.
In foggy weather or in snow, thesunshine sensor may detect sufficient light. The lighting will not come on automatically. Do not cover the sunshine sensor, theassociated functions will no longer becontrolled.

Visibility
60





Courtesy lamp
Position 1 "ON"
The cour tesy lamp is permanently on.
Position 2 "●"
The cour tesy lamp comes on when openinga door or the boot; when the door or boot isclosed again, the lighting gradually dims for a few seconds before going off.
However, the cour tesy lamp is switched off
immediately when the doors and boot are closed and you lock the vehicle from the inside
or using the remote control.

Position 3 "OFF"

The cour tesy lamp is permanently off.