2011 CADILLAC DTS cruise control

Black plate (16,1)Cadillac DTS Owner Manual - 2011
{WARNING:
.On winding roads, Adaptive Cruise Control
may not detect a vehicle ahead. You could
crash into a vehicle ahead of you. Do not use
Adaptive Cruise Control on winding roads.
.Adaptive Cruise Control may not have time to
slow your vehicle enough to avoid a crash
when you are driving in conditions where
vehicles may suddenly slow or stop ahead of
you, enter your lane, or cross your vehicle's
path. If you are driving in these conditions, do
not use Adaptive Cruise Control. The warning
beep and alert symbol may indicate that you
are driving in conditions where Adaptive
Cruise Control should not be used. See
“Alerting the Driver”in this section.
(Continued)
WARNING: (Continued)
.On slippery roads, fast changes in tire traction
can cause needless wheel spinning, and you
could lose control. Do not use cruise control
on slippery roads.
.When weather limits visibility, such as when in
fog, rain, or snow conditions, Adaptive Cruise
Control performance is limited. There may not
be enough distance to adapt to the changing
traffic conditions. Do not use cruise control
when visibility is low.
4-16

Black plate (17,1)Cadillac DTS Owner Manual - 2011
The ACCs are located on the steering wheel.
The cruise control buttons are located on left side of the
steering wheel.
](On):Press to turn the system on.
+ Res (Resume/Accelerate): Press to make the
vehicle resume to a previously set speed or to increase
the set speed when ACC is already active.
Set–: Press to set the speed or to decrease the set
speed when ACC is already active.
[(Cancel): Press to disengage ACC without erasing
the set speed from memory. +GAP (Increase Following Distance):
Press to
increase the distance between your vehicle and other
vehicles.
−GAP (Decrease Following Distance): Press to
decrease the distance between your vehicle and other
vehicles.
ACC will not work if the master cylinder brake fluid level
is low.
Engaging ACC With the Set Button
If the adaptive cruise control switch is on when not in
use, it could get bumped and go into cruise when not
desired. Keep the adaptive cruise control switch off
when cruise is not being used.
The set speed is selected by the driver. This is the
speed your vehicle will travel if there is no vehicle
detected in its path.
To set ACC, do the following:
1. Press the
]button.
2. Get up to the speed desired.
3. Press in the SET– button and release it.
4. Take your foot off the accelerator pedal.
Once ACC is set, it may immediately apply the brakes if
it detects a vehicle ahead is too close or moving slower
than your vehicle.
4-17

Black plate (19,1)Cadillac DTS Owner Manual - 2011
There are six follow distances to choose from. The
follow distance selection ranges from near to far
(one second to two seconds follow time). The distance
maintained for a selected follow distance will vary
based on vehicle speed. The faster the vehicle speed
the further back your vehicle will follow. Consider traffic
and weather conditions when selecting the follow
distance. The range of selectable distances may not be
appropriate for all drivers and driving conditions. If you
prefer to travel at a follow distance farther than ACC
allows, disengage the system and drive manually.
Alerting the Driver
The ACC alert symbol is
located on the display at
the top of the instrument
panel to the right of the
driver.
The alert symbol flashes and a warning beep sounds
when driver action may be required. If ACC is engaged,
the alert symbol will flash when:
.ACC cannot apply sufficient braking because you
are approaching a vehicle too rapidly.
.The vehicle speed drops below about 32 km/h
(20 mph).
.A temporary condition prohibits ACC from
operating. See DIC Warnings and Messageson
page 4‑65for more information.
.A malfunction is detected in the system. See DIC
Warnings and Messageson page 4‑65for more
information.
See Defensive Driving on page 5‑2.
{WARNING:
Adaptive Cruise Control has only limited braking
ability to slow your vehicle. In some cases,
Adaptive Cruise Control may not have time to
slow your vehicle enough to avoid a collision. Be
ready to take action and apply the brakes
yourself. See Defensive Driving on page 5‑2.
4-19

Black plate (20,1)Cadillac DTS Owner Manual - 2011
Approaching and Following a Vehicle
The vehicle ahead symbol
is located on the top of
the instrument panel to
the right of the driver.
The vehicle ahead symbol only appears when a vehicle
is detected in your path.
If this symbol does not appear, or disappears briefly,
ACC will not respond to vehicles you may see ahead.
{WARNING:
When the Adaptive Cruise Control radar is
blocked by snow, ice, or dirt, it may not detect a
vehicle ahead. Adaptive Cruise Control may not
have time to slow your vehicle enough to avoid a
collision. Do not use Adaptive Cruise Control
when the radar is blocked by snow, ice, or dirt.
Keep your radar clean. See “Cleaning the
System” later in this section. ACC automatically slows your vehicle down when
approaching a slower moving vehicle. It then adjusts
your vehicle speed to follow the vehicle in front at the
selected follow distance. Your vehicle speed increases
or decreases to follow the vehicle in front of you, but will
not exceed the set speed. It may apply limited braking,
if necessary. When braking is active, your brake lights
will come on. Braking may feel or sound different than if
you were applying the brakes yourself. This is normal.
Stationary or Very Slow-Moving Objects
{WARNING:
Adaptive Cruise Control may not detect and react
to stationary or slow‐moving vehicles or other
objects ahead of you. You could crash into an
object ahead of you. Do not use Adaptive
Cruise Control when approaching stationary or
slow‐moving vehicles or other objects.
4-20

Black plate (21,1)Cadillac DTS Owner Manual - 2011
{WARNING:
Adaptive Cruise Control may not detect and react
to stationary or slow-moving vehicles or other
objects ahead of you. Your vehicle may accelerate
toward objects, such as a stopped vehicle that
suddenly appears after the lead vehicle changes
lanes. Your complete attention is always required
while driving and you should be ready to take
action and apply the brakes.
Low-Speed Deactivation
If your vehicle speed falls below 32 km/h (20 mph) while
following a vehicle ahead, ACC will begin to disengage.
The Driver Alert symbol will flash and the warning beep
will sound. The driver must take action since ACC will
not slow the vehicle to a stop.
Passing a Vehicle/ACC Override
To increase speed to pass a vehicle, use the
accelerator pedal. While you are doing this, the system
will not automatically apply the brakes. A message will
appear on the DIC. SeeDIC Warnings and Messages
on page 4‑65. Once you remove your foot from the
accelerator pedal, ACC will return to normal operation
and be able to apply the brakes, if needed.
{WARNING:
If you rest your foot on the accelerator pedal, the
system will not automatically apply the brakes.
You could crash into a vehicle ahead of you. Do
not rest your foot on the accelerator pedal when
using Adaptive Cruise Control.
4-21

Black plate (22,1)Cadillac DTS Owner Manual - 2011
Curves in the Road
{WARNING:
Due to Adaptive Cruise Control limitations in
curves, it may respond to a vehicle in another
lane, or may not have time to react to a vehicle in
your lane. You could crash into a vehicle ahead of
you, or lose control of your vehicle. Give extra
attention in curves and be ready to use the brakes
if necessary. Select an appropriate speed while
driving in curves.
ACC may operate differently in a sharp curve. It may
reduce your vehicle speed if the curve is too sharp.
When following a vehicle and entering a curve, ACC
could lose track of the vehicle in your lane and
accelerate your vehicle. When this happens the Vehicle
Ahead symbol will not appear.
4-22

Black plate (23,1)Cadillac DTS Owner Manual - 2011
ACC may detect a vehicle that is not in your lane and
apply the brakes.
ACC may, occasionally, provide a driver alert and/or
braking that you consider unnecessary. It could respond
to signs, guardrails, and other stationary objects when
entering or exiting a curve. This is normal operation.
Your vehicle does not need service.
Highway Exit Ramps
{WARNING:
Adaptive Cruise Control may lose track of the
vehicle ahead and accelerate up to your set
speed while entering or on highway exit ramps.
You could be startled by this acceleration and
even lose control of the vehicle. Disengage
Adaptive Cruise Control before entering a
highway exit ramp. Do not use Adaptive Cruise
Control while entering or on exit ramps.
Other Vehicle Lane Changes
If another vehicle enters the same lane as you, ACC will
not detect the vehicle until it is completely in the lane.
Be ready to take action and apply the brakes yourself.
4-23

Black plate (58,1)Cadillac DTS Owner Manual - 2011
Front Fog Lamp Light
The fog lamp light comes
on when the fog lamps
are in use.
The light goes out when the fog lamps are turned off.
See Fog Lamps
on page 4‑29for more information.
Lights On Reminder
This light comes on
whenever the parking
lamps are on.
See Exterior Lamps
on page 4‑25for more information.
Cruise Control Light
This light comes on
whenever the cruise
control is set.
The light goes out when the cruise control is turned off.
See Cruise Control
on page 4‑12andAdaptive Cruise
Controlon page 4‑14for more information.
Highbeam On Light
This light comes on when
the high-beam headlamps
are in use.
See Headlamp High/Low-Beam Changer
on page 4‑6for more information.
4-58