2011 AUDI A5 COUPE load capacity

Seats and storage
& WARNING
After traveling several miles, ensure that the roof rack is secure.
[ i ] Tips
The roof rack ind icates whether it is to be mounted in the front or
back .a
Roof load
T h e cargo on the roof must be securely attached.
H andling characteristics change when cargo is trans ­
p orted.
The pe rmissible roof load for yo ur vehicle is 165 lb s. (75 kg ). The
roof load is a combination of the weight of the carrier system and the
c argo .
When using roof rack systems with a lower load capacity , you cannot
use the maximum permissib le roof load. In t his case, the roof rac k
can o nly be loaded to the weight limit g iven in the insta llation g uide .
& WARNING
• The cargo must be securely attached on the roof rack , other­
wise you ri sk an accident .
• You must under no ci rcumstances exceed the permissible roof
load, the permissible axle loads and the permissible overall
weight of your vehicle· risk of an accident .
• Consider that when transporting heavy objects
or one with a
large surface, the handling characteristics change due to shift in
the center of gravity or the greater surface exposed to the wind. So
adapt your driving and your speed to prevailing conditions .
W For the sake of the environment
As a result of the increase wind resistance created by a roof rac k, yo ur
vehicle is using fue l unnecessari ly. So remove the roof rack after
using i t.•
Beverage holders
Front beverage holders
Fig. 90 Cent er
console : Front
bev erag e holder s
Fig. 91 Be verage
storage in th e rear
a rmrest
- You can accommodate two beverages in t his sto rage
=> fig . 9 0.

______________________________________________ D_ ri _v _ i_n _,,g ~ S_a_ f_ e_ l_,, y '--- __
label is located on the driver's side 8-p illar . On Canada veh icles, the
ti re pressu re lab el is loca ted ei ther on the d river's s ide 8-pillar or
inside the fuel fille r flap . The tire pressure label lists the recom­
mended co ld tire inflatio n pressures fo r the ve hicle at its maximum
capacity weight and the tires that were on yo ur vehicle at the t ime it
was manufactured . For recommended tire pressures for normal loa d
c ondi tions, p lease see chapte r=>
page 295. •
Tie-downs
The luggage compartment is equippe d with four tie­
d o w ns to secu re lu ggage and other i tems.
Use the t ie-downs to sec ure yo ur ca rgo prope rly=> page 177 ,
"Load ing the luggage compartment" .
In a c oll ision, t he laws of physics mean that eve n small er item s tha t
are loose in the vehicle will become heavy missiles that can cause
s er iou s injury. Ite ms i n t he vehi cle p osses s ene rgy w hich vary w it h
vehicle speed and the weight of the item. Vehicle speed is th e most
sig nifi ca nt fa ctor.
For examp le, in a frontal collis ion at a speed of 30 mph (4 8 km/h) ,
the forces acting on a 10- lb (4.5 kg) object are a bout 20 times the
normal weig ht o f th e ite m. Th is mea ns that t he weight of t he ite m
wou ld s uddenly be abo ut 200 lbs. (90 kg) . You can imagine the inju­
r ies tha t a 200 lbs . (9 0 kg) item fly ing freely throug h the pa ssenge r
compartment could cause in a collision like this.
& WARNING
Weak , damaged or improper straps used to secure items to tie­
downs can fail during hard braking or in a collision and cause
serious personal inju ry.
• Always use suitable mounting straps and properly secure items
to the tie-downs in the luggage compartment to help prevent
items from shifting or flying forward as dangerous missiles.
Controls and equip­ ment Safety first Vehicle operation
& WARNING
(co ntinued )
• When the rear seat backrest is folded down, always u se suit­
able mounting straps and properly secure items to the tie-downs
in the luggage compartment to help p revent items from flying
forward as dangerous missiles into the passenger compartment .
• Never attach a child safety seat tether strap to a tie-down. •
Reporting Safety Defects
Applicable to U.S.A.
If you believe that your vehi cle has a defect
which could cause a crash or could cause injury or death , you should immediately inform the
National Highway Traffic Safety Administration
(NHTSA) in addition to notifying Audi of
America, Inc.
If NHTSA receives similar complaints, it may
open an investigation , and if it finds that a
safety defe cts exist s in a group of vehicles, it
may o rder a recall and remed y campaign.
However, NHTSA cannot become involved in
individual problems between you , your dealer,
or Audi of America, Inc .
To contact NHTSA, you m ay call the Vehicle
Safety Hotline toll-free at:
Tel.: 1-888-327-4236 (TTY: 1-800-424-9153) _,.
Vehicle care Do-it-yourself service Technical data

Intelligent technology
~----------------------------------------------
Intelligent technology
Notice about data recorded by
vehicle control modu Les
Your vehicle is not equipped with an Event Data Recorder (EDR),
installed by some manufacturers for the express purpose of
capturing data for retrieval after an accident or crash event. EDR's are
sometimes called "crash recorders".
Some state laws restrict the retrieval or downloading of data stored
by ED R's that were installed in a vehicle for the express purpose of
retrieving data after an accident or crash event without the owner's
consent.
Although your vehicle is not equipped with an EDR, it is equipped with
a number of e lectronic control modules for various vehicle systems
such as, for example, eng ine function, emission control, as well as for
the airbags and safety belts.
These electronic control modules also record vehicle-related data
during normal vehicle operation for diagnostic and repair purposes .
The recording capacity of the electronic control modu les is limited to
data (no sound is recorded) and only a sma ll amount of data is actu­
ally recorded over a very limited period of time and stored when a
system fault or other condition is sensed by a control unit. Some of
the data then stored may relate to vehicle speed, direction, braking
as well as restraint system use and performance in the event of a
crash or other condition. Stored data can only be read and down­
loaded with special equipment .•
Electronic stabilization Program
(ESP}
Ce-ieral lnforrrc:t~on
The ESP improves the vehicle stability.
Fig. 197 ;';. OFF
button
Fig. 198 Center
console with;';.
OFF
button
ESP is designed to he lp you maintain vehicle control in situations
where the car approaches the limits of "grip", especially when accel­
erat ing and cornering. ESP reduces the risk of skidding and improves
stability under all road conditions.

-~_T_ ir_e_ s_ a_ n_ d_ w_ h_e_ e_ ls _______________________________________________ _
& WARNING (conti nu ed )
• Tire s age even if they are not being used and can fail suddenly ,
especially at high speeds . Tires that are more than 6 year s old can
only be used in an emergency and then with special care and at low
s peed .
Glossary of tire and loading terminology
Accessory weight
means the combined we ight (in excess of those sta nda rd items which
may be rep lace d) of automatic transmission, power steering, power
bra kes, powe r w indows , power seats, radio, and heater, to the extent
that these items are avai lab le as factory- installed equipment
(w het he r i nsta lled or no t).
Aspect ratio
me ans the ratio of t he he ight to t he w id th of the tir e in percent .
Numbe rs of 55 o r lower indicate a low sidewa ll for improved steer ing
respo nse an d be tter overa ll handling on dry p avemen t.
Bead
means the part o f the tire that is made of stee l w ires , wrap ped o r
re in forced by ply cords and that is shaped to fit the rim.
Bead separation
means a brea kdown of the bon d between components in the bead .
Cord
means the st rands forming the plies in the tire.
& W ARNING (continued )
• Never mount used tire s on your vehicle if you are not sure of
their "previous hi story ." Old used tires may have been damaged
eventhoughthedamagecannotbeseenthatcanleadtosudden
tire failure and lo ss of vehicle control.
• If you notice unu sual vibration or if the vehicle pull s to one side
when driving, alway s stop as soon as it is safe to do so and check
the wheels and tires for damage. •
Cold tire inflation pressure
means the tire pressure recommended by the vehicle ma nufa cturer
for a tire of a des ignated size t hat has not been driven for more than
a couple of m iles ( kilomete rs) a t low speeds in the t hree ho ur period
before the tire pressure is measured or ad justed.
Curb weight
mea ns the weig ht of a motor vehicle wit h standard equ ipment
including the max imum cap aci ty of f ue l, oil, and coo lan t, air condi ­
tioning and additiona l weight of optional equipment.
Extra load tire
means a tire design to operate at higher loa ds and at higher inflation
pressures than the co rrespo nd ing standard tire. Extra load tires may
be identified as "XL", "xl", "EXTRA LOAD", or "RF" on the sidewal l.
Gross Axle Weight Rating ( "GAWR ")
means the load -ca rry ing capacity of a s ingle ax le system, measured at
t he t ire-grou nd inte rfaces .
Gross Vehicle Weight Rating ("GVWR")
means the max imum total loaded we ight of the vehicle .

-~_T_ ir_e_ s_ a_ n_ d_ w_ h_e_ e_ ls _______________________________________________ _
Sidewall
means that portion of a tire between the tread and bead.
Speed rating (letter code)
means the speed at which a tire is designed to be driven for extended
periods of time. The ratings range from 93 mph (150 km/h) to 186
mph (298 km/h) =>
page 304. You may not find this information on
all tires because it is not required by law.
The speed rating letter code, where applicable, is mo lded on the tire
sidewall and indicates the maximum permissible road speeds=>
& in
"Winter tires" on
page 307.
Tire pressure monitoring system*
means a system that detects when one or more of a vehicle's tires are
unde rinflated and illuminates a low tire pressure warning te lltale.
Tread
means that portion of a tire that comes into contact with the road.
Tread separation
means pulling away of the tread from the tire carcass.
Treadwear indicators (TWI)
means the projections within the princ ipal grooves designed to give a
visual ind ication of the degrees of wear of the tread. See=>
page 301,
"Tread Wear Indicator (TWI)" for more information on measuring
tire wear.
Uniform Tire Quality Grading
is a tire informat ion system developed by the United States National
H ighway Traff ic Safety Adm inistration (NHTSA) that is designed to
help buye rs make relative comparisons among tires. The UTQG is not
a safety rating and not a guarantee that a tire will last for a prescribed
number of miles (ki lometers) or perform in a certain way . It simp ly
gives tire buyers additional information to combine with other
considerations, such as price, brand loyalty and dea ler recommenda­
tions. Under UTQG, tires are graded by the tire manufacturers in three areas: treadwear, traction, and temperature
resistance. The UTQG
info rmat ion on the tires, molded into the sidewalls.
U.S. DOT Tire Identification Number (TIN)
This is the tire 's "serial numbe r". It beg ins with the letters "DOT" and
ind icates that the tire meets all federal standards. The next two
numbers or letters ind icate the plant where it was manufactu red, and
the last four numbers represent the week and year of manufacture.
For examp le,
DOT ... 2209 ...
means that the tire was produced in the 22nd week of 2009. The
o ther numbers are marketing codes that may or may not be used by
the t ire manufacturer. Th is informat ion is used to contact consumers
if a tire defect requires a recall.
Vehicle capacity weight
means the rated cargo and l uggage load plus 150 lbs. (68 kilograms)
times the vehicle 's total seating capacity as listed on the label located
either on the driver's side B-pillar or on the ins ide of the fu el filler
flap.
Vehicle maximum load on the tire
means that load on an individual tire that is determined by distrib­
ut ing to each axle its share of the max imum loaded vehicle weight
and dividing by two.
Vehicle normal load on the tire
means that load on an individual tire that is determined by distrib­
ut ing to each axle its share of the curb weight, accessory weight, and
normal occupant weight (distributed in accordance with tab le below
=>
page 295) and dividing by two. ~

________________________________________________ T_ i_ re _ s_ a_ n_d_ w_ h_ e_ e_l _s _ ....... JIII
Occupant loading and distribution for vehicle normal load for various designated seat ing capacities
Designated seating capacity, num- Vehicle normal load , number of Occupant distribution in a nor­
mally loaded vehicle
ber
of occupants occupants
4 2 2 in front •
Co ld tire inf lation pressure
Tire pr essur e aff ects the overall handling, performance and safety of a vehicle.
F ig . 2 12 Tire pre ssure
label : loca te d e ithe r on
drive r's s ide B -pillar or
i ns ide th e fuel fille r
flap
Tire pressure generally refers to the amount of air in a tire that it
nee ds it to do its job and safe ly ca rry the combi ned load of t he en tire
vehicle and its contents. Tire pressure is measured in kilopascals
(kPa), the inte rn ational measuri ng un it and in pou nds per square i nch
(PSI) . Tire pressure is based in part on the ve hicle's design and load
limit -the greatest amount of weight that the vehicle can ca rry safe ly
and the t ire size . The proper tire pressure is frequent ly refe rred to as
the "recommended cold t ire inflation pressure ." Air in t he tires
expands when the t ire hea ts up because of i nternal fric tion whe n it
flexes in use . The tire press ure is higher when the ti re has warmed up
t han whe n it is "cold."
It is the inflat io n pr essu re in a "co ld" t ire that
counts. The refore, you sho uld never let air out of a warm t ire to
match "cold ti re infla tion pressure" recommendations . The t ires
would then be under inflated and could fail suddenly.
Vehicle OP-eration
(.
~ ( SEATING CAPACllY JOTAL l:FRONT l:CENTER I )!EAR I )
TIRE AND LOADING INFORMATION
Tot--""'91"dOCC10-,ndQ,gc>"""-"1 ___ "90<- lb$.
TIRE SIZE COW TIRE PRESSURE
FRONT -KPa, - PSI
REAR -KPa, -PSI
Fig . 213 Tire pres sure
label
Ma intain ing proper tire pressure is one of the most important things
you can do to he lp avoid sudde n tir e f ailur e. Under infl ated tires a re a
major cause of sudden tire fa ilure. Keep ing t ires at the rig ht pressure
is a lso important for s afe and responsive vehi cle ha nd ling, tractio n,
braking and load carrying.
Tire pressures are particularly important
when the vehicle is being driven at higher speeds , and then e spe·
cially when heavily loaded even within the permissible load­
carrying capacities approved for your vehicle .
The recommended tire pressures for your Audi depend on the kind of
ti res on your vehicle and the numbe r of passengers and/or amou nt of
l u ggage you will be transpo rting .
On USA vehicles, the tire pressure label is located on the d river 's side
8 -pi lla r. O n Ca nada vehi cles, the tire pressure label is located either
on t he driver's side 8- pilla r o r i nside the f uel filler flap . The tire pres ·
s u re labe l lists the recommended co ld tire inflation press ures for the ..,.
Vehicle care Do-it-yourselt service iTechnical data

-~_T_ ir_e_ s_ a_ n_ d_ w_ h_e_ e_ ls _______________________________________________ _
vehicle at its maximum capacity weight and tires that were on your
vehicle at the tim e it was manufactured.
If you wish to improve comfort when operating the vehicle at
normal load (up to 3 occupants) , you can adjust tire pressures to
those specified for normal vehicle load. Before operating the
vehicle at maximum load, you must increase the tire pressures to
those specified for maximum vehicle load
=> &.
Bear in mind that the tire pressure monitoring system* ca n only
monitor the tire pressures you have stored. The system does not
recogn ize the load condit ion of your vehicle.
The effectiveness of the tire pressure monitoring system* wi ll be
impaired if you store normal load pressures but then operate the
vehicle at its maximum load
=> &.
See the illustration => page 295, fig. 212 for the locat ion of the label
either on driver's side B-pillar or inside the fuel filler flap (color of the
actual label and exact location on the vehicle will vary slightly).
Note that the following tab le is accurate at the time of going to press
and is subject to change. In the event of discrepancies, the tire pres­
sure label (On USA vehicles, the tire pressure label is located on the
dr iver's side B-pillar. On Canada vehicles, the tire pressure label is
located e ither on the driver's s ide B-pillar or inside the fuel filler flap)
always takes precedence.
The table below lists the recommended cold tire inflation pressures
for the Audi model covered by your Owner's Literature at the vehicle's
capacity weight and the tire sizes installed on the respective models
as origina l equipment, or as a factory option.
Engine
(displace­ ment in liter) Tire designation
Tire pressure front Tire pressure rear
normal load normal load
condition (up full load condition
(up
full load
to 2 occu- condition to 2 occu- condition pants) pants)
PSI Jl kPA PSI kPA PSI kPA PSI II kPA
4-cylinder 225/50 Rl 7 94H All Season 32 220 33 230 29 200 33 230
2.0
245/45 Rl 7 95H All Season 32 220 33 230 29
200 33 230
245/40 R18
93H All Season 33 230 35 240 29 200 35 240
255/35 R19 96V XL High Performance 32 220 33 230 32 220 33 230
265/30 R20 94Y XL High Performance 30 210
33 230 29 200
33 230
XL=
reinforced or extra load tire. It may also appear as xi, EXTRA LOAD, or RF on the tire sidewall.
The correct tire pressure for the spare wheel is located on a label
either on the driver's s ide B-pillar or inside the fuel filler flap.
Beca use technica l changes may be made to vehicle equipment during
the model year, always compare the tir e s ize designation on the tir e
pressure label on your vehicle with the tires on your vehicle. Make sure that the tire size information on the vehicle label is the same as
the
size of the tires on the vehicle. This is especially important if the
vehicle belongs to someone e lse or you bought the vehicle with
different rims/tires or you bought the veh icle as a previous ly ow ned
vehicle. _.,,

______________________________________________ T_i_r _e _s _ a _ n_d_ w_ h_e_ e_ ls __ l!'II
Remember, your safety and t hat o f your passengers also depends o n
making sure th at load limit s are not exc ee ded . V ehicle load in cludes
every body and everything in a nd on the veh icl e. These load limits are
tec hnically refer red to as t he ve hicle's G ross Vehicle Weight Rating
("G VWR") . The Gross Axle Weight Rat ing ("GA WR") is th e max imum
load that can be a pplied at each of the ve hicle's two ax les. The Gross
Vehicle Weigh t Rating and the G ross Ax le W eig ht R ating are listed on
the safety comp liance st ic ker label located either on the driver's side
B -pillar or on t he inside of th e f uel fi ller f lap. T he tire press ure label
on yo ur Audi lists the maximum comb ined weig ht of all of the occu­
p ants a nd lugg age o r othe r car go tha t t he ve hicl e c an ca rry . Fo r the
location of t he tire pressure label~
page 295, fig. 212.
& WARNING
Overloading a vehicle can cause loss of vehicle control , a crash or
other accident, serious personal injury, and even death .
• Carrying more weight than your vehicle was designed to carry
will prevent the vehicle from handling properly and increase the risk of a loss of vehicle control.
• The brakes on a vehicle that has been overloaded may not be
able to stop the vehicle within a safe distance.
• Tires on a vehicle that has been overloaded can fail suddenly
causing loss of control and a crash.
• Always make sure that the total load being transported -
including the weight of a trailer hitch and the tongue weight of a
loaded trailer -does not make the vehicle heavier than the
vehicle's Gross Vehicle Weight Rating.
& WARNING
• Incorrect tire pressure s and/or underinflation can lead to a
serious or fatal accident .
• Incorrect tire pressures and/or underinflation cause increased
tire wear and can affect the handling of the vehicle .
Safety first
& WARNING (cont inued )
• Incorrect tire pressures and/or underinflation can also lead to
sudden tire failure, including a blowout and sudden deflation,
causing loss of vehicle control. •
Checking tire pressure
The cor rect t ire pres sure fo r the tires o rig inall y installed
on you r veh icle is list ed o n the t ire pr ess ure la bel l ocat ed
e ither on driver's s ide 8-pillar or insi de th e fue l fill er flop.
Th e recommended tire pressure s are on the tire pressur e l abe l and in
the table ~
page 295, "Cold tire inflation press ure" .This means that
t he pressure must be check ed an d a dju sted w hen the tire h as no t
been dr iven for more tha n a cou ple of m iles (k ilometers) at low
s peeds dur ing t he pr evious t hree hour s. Air in the tires ex pands w hen
t he tire heats up as a resu lt of i nterna l fric tion as it flexes in use. The
tire pressu re is hig he r when the t ire has warmed up than when it is
"cold ."
It is the in flation press ure in a "cold" t ire that counts. Therefore, yo u
sh oul d n eve r le t a ir ou t of a warm t ir e to ma tch "C old tire in flatio n
pressure" recommendations~
page 295. The t ires would then be
unde rin flat ed and co uld fail su ddenly.
Th e tire pressu re labe l on yo ur Audi lists t he recommended co ld t ire
inflation pressures at ma ximum capacity fo r th e new, o rigina l equip ­
me nt t ires that were on yo ur vehicl e at th e time it wa s manuf actured .
For the location of t he label ~
page 295, fig. 212.
M ost t ires lose air natura lly ove r time. T hey c an also lose some air if
you d rive over a potho le or hit a curb while pa rking . It is usually not
poss ible to see whether the radia l ti res used today are unde rinflate d
just by loo king at them .
T he refore, be sure to check t ire pressures at least once a month and
alw ay s before go ing on a lo ng trip. Make sure to take the num ber of
people and the amount of luggage into account whe n ad justing tire .,.
Vehicle care Technical data