2011 AUDI A5 COUPE seats

...,. Child Safety P#J'I ____ _,.__ __________________________ _
Location
Fig. 191 Schematic
overview: LATCH
anchorage point loca­
tions
The illustration shows the seating locations in your vehicle which are
equipped with the lower anchorages system. •
Description
The lower anchorage positions are marked for quick
locating.
Fig. 192 Lower
anchorages,covers
marked
Lower anchorages
Fig. 193 Rear seats:
lower anchorage
bracket locations
Th e lower anchorage attachment points are located on the rear end
of the rear seatback.
Remove the covers=> fig. 192 to access the lower anchorage attach­
ment points .
The lower anchorage attachment points are visible=> fig. 193.
Lower anchorages secure the child restraint in the seat without using
the vehicle's safety belts. Anchorages provide a secure and easy-to­
use attachment and minimize the possibility of improper child
restraint installation .
All child restraints manufactured after September 1, 2002, must have lower anchorage attach men ts for the
LATCH system.
Please remember that the lower anchorage points are only intended
for installation and attachment of child restraints specifically certi­
fied for use with
LATCH lower anchorages. Child restraints that are
not equipped with the lower anchorage attachments can still be
installed in compliance with the child restraint manufacturer's
instructions on using vehicle safety belts .
& WARNING
Improper use of LATCH lower anchorages can cause serious
personal injury in an accident.

Child Safety -
-------------------"'---
& WARNING (continued)
• Always carefully follow the child restraints manufacturer's
instructions for proper installation of the child restraint and
proper use of the lower anchorages or safety belts in your vehicle.
• Never secure or attach any luggage or other items to the
LATCH
lower anchorages.
• Always read and heed the important information about child
restraints in this chapter and WARNINGS~ page
215, "Child
Safety ".•
Installing a child restraint with LATCH
Lower anchorages
Whenever you install a child restraint always follow the
child restraint manufacturer's instructions.
Mounting
Fig. 194 Lower
anchorages : proper
mounting
- Make sure the seatback of the rear seat bench is in the
upright position and securely latched in place.
Controls and equip­
ment Safety first Vehicle operation
-
Attach both hook-on connectors with the spring catch
release on the child safety seat onto the LATCH lower
anchorage so that the connectors lock into place
=> fig. 194.
-Pull on the connector attachments to make sure they are
properly attached to the LATCH lower anchorage.
- Pull straps tight following the child restraint manufac­
turer's instructions .
Releasing
-Loosen the tension on the straps following the child
restraint manufacturer's instructions.
- Depress the spring catches to release the anchorage hooks
from the lower anchorages.
Remember: Use tether straps to help keep the child restraint firmly
in place.
& WARNING
Improper use of the LATCH system can increase the risk of serious
personal injury and death in an accident.
• These anchors were developed only for child safety seats using
the "LATCH" system.
• Never attach other child safety seats, belts or other objects to
these anchors.
• Always make sure that you hear a click when latching the seat
in place. If you do not hear a click the seat is not secure and could
fly forward and hit the interior of the vehicle, or be ejected from
the vehicle.
l)l,
Vehicle care Do-it-yourself service Technical data

lffll.,___C_h_ i_ ld _ S_ a_ f_ e_ t...:: y ;....__ _________________________________________ _
in. WARNING
Improper installation of child restraints will increase the r isk of
injury in an accident.
• Always follow the child restraint system manufacture r's
instructions for proper in stallation of the child restraint sy stem
and proper use of tether straps as well as the lower anchorages or
s afety belts in your vehicle .
• Always read and heed the important informat ion and WARN·
INGS about child safety and the installation of child restraint
systems ~
page 215, "Child Safety ".•
Tether anchors and tether straps
Fig . 1 9 5 T ether
a n ch ors : rece ss fl aps
behind th e rear seat ­
bac ks
The tether anchors for the rear seat ing pos itions are located i n
recesses in the rear win dow sh elf ~ fig. 195 .
A tet he r i s a st raight o r V-shaped strap t hat attac hes the top pa rt of
a ch ild restraint to spec ia l anchorage points in the vehicle .
T he p urpo se of the tethe r is to reduce t he f orwar d movemen t of the
child restraint in a crash, in order to help reduce t he risk of head injury
t ha t could be caused by st riking the ve hicle in terior .
Forward fac ing ch ild restraints manufactured after September 1,
1 999, are required by U.S . federa l reg ulations to comply with child head movement performance req
uirements . T hese new performance
re qu iremen ts m ake a tet he r ne cessa ry on most new child sa fe ty
seats.
in. WARNING
Improper installation of child restraints will inc rease the risk of
injury and death in a cra sh .
• Alw ays follow the instructions pro vided by the manuf acturer
of the child restraint you intend to install in your Audi.
• Improper use of child re straint anchors (including tether
anchors) can lead to injury in a collision. The anchor s are designed
to withstand only those loads imposed by co rrectly fitted child
restraint s.
• Never mount two child restraint systems on one LATCH lower
anchor point .
• Never attach two child restraint systems to one tether strap or
tether anchorage.
• Never attach a tether strap to a tie-down hook in the luggage
compartment .
• Never u se child restraint tether anchorage s to secure safety
belts or other kinds of occupant rest raints.
• Never secure or atta ch any luggage or other items to the LATCH
lower anchorages or to the tethe r ancho rs.
• If a tether or other strap is used to attach a child restraint to
the front passenger seat , make sure that it is not so tight , that it
causes the weight -sensing mat to mea sure more weight than is
actually on the seat.
• The heavier weight register ed can make the Advanced Airbag
System work as though an adult were on the seat and deploy the
Advanced Airbag when it must be suppre ssed causing serious or
even fatal injury to the child.
• If you must install a rearward facing child safety seat on the
front passenger seat because of e xcept ional circumstances and
the PASSENGER AIR BAG OFF light does not come on and stay on,
~

& WARNING (co ntinued )
immediately install the rear -facing child safety seat in a rear
s eating position and have the airbag sy stem in spected by your
Audi deale r.•
Installing the upper tether strap on the
anchorage
(
Installing the tether strap
Fig . 1 9 6 Te ther st rap :
prop er routi ng and
mounting
- Release or dep loy the tet her strap on the ch ild rest raint
acco rd ing to the ch ild restra int ma nufacturer's instruc ­
tions.
- Guide t he upper tet her st rap
under t h e rear head restraint
:::;, fig. 196 (raise t he head restra int if necessary).
- Tilt the recess fla p up to expose the anchor bracket.
- Attac h the t ether st rap anchora ge h ook in to the op ening
o f th e tet her anchorage .
- Pull on the tethe r strap hook so that the spring catch of
t h e hoo k engages.
Safety first Vehicle OP-eration
Child Safety
-Tig hten t he tether strap firmly fo llowi ng th e ch ild
restra int man ufacturer 's ins tructions .
Releasing the tether strap
- Loosen t he tension following t he chil d restrai nt manufac ­
turer's i nstructions.
- D epress t he spr ing catc h on the hoo k and release it f rom
t h e anchorage.
0 Note
If you leave the child restra int wit h the tether st rap firmly installed
for several days, t his could leave a mark on t he up holstery on t he seat
c u shi on and backrest in the area whe re the tether strap was insta lled .
Th e up ho lstery would also be permanent ly stretched a round the
tether st rap. This appli es especially to leather seats. •
Using tether straps on rearward-facing
child restraints
Currently, few rearward-facing child restraint systems come wit h a
t e ther. Please read and heed the ch ild restraint system ma nufac­
t u rer 's instructions care fully to determine how to properly install the
t ether.
& WARNING
A child in a rearward-facing child safety seat installed on the front
passenger seat will be seriously injured and can be killed if the
front airbag inflates -even with an Ad vanced Airbag System.
• The inflating airbag will hit the ch ild safety seat or infant
carrier with great force and will sma sh the child safety seat and
child against the bac krest, center armrest , or door . •
Vehicle care Do-it-yourselt service iTechnical data

Intelligent technology
'-------------------------------------------------
vi dual components. It regulates consumption, so that more electrical
energy is not being used than is being generated and ensures an
optimal state of charge for the battery .
[I] Tips
• But even energy management cannot negate the limits of physics.
Consider that the power and life of a battery are limited.
• If starting ability is threatened, you are informed by a warning
~ page 245, "Driver notification in the instrument cluster display" .•
What you should know
The highest priority is given to maintaining starting capa ­
bility.
Th e battery is severe ly taxed in short-distance driving, in city traffic
and during the cold time of year. Abundant electrical energy is
required, but only a little is generated.
It is also critical if the engine
is not running and electrical components are turned on. In this
instance energy is being consumed but none is being generated.
It is in prec ise ly these sit uations that you will notice energy manage­
ment actively regulating the distribution of energy.
Vehicle stands for an extended period
If you do not drive your vehicle over a period of several days or weeks,
electrical components are gradually cut back or sw itched off. This
reduces energy consumption and maintains starting capability over a
longer period.
Take into consideration that when you unlock your vehicle, some
convenience functions, such as the remo te key or power seat adjust­
ment, may not be available. The convenience functions will be avail­
able again when you turn on the ignition and start the engine.
W ith the engine turned off
If you listen to the radio, for example, with the engine turned off or
use other MMI functions, the battery is being discharged .
If starting capability is jeopardized due to energy consumption, the
following warning appears in the MMI display:
Please start engine, otherwise system will switch off in
3 minutes.
Th e warn ing indicates that the system will be turned off automati­
cally after 3 m inutes. If you wish to continue using the functions, you
have to start the engine.
With the engine running
Although electrica l energy is generated when the vehicle is being
driven, the battery can become discharged. This happens most ly
when little energy is being generated and a great deal consumed and
the battery's state of charge is not optimal.
T o br ing the ene rgy balance back into equilibrium, consumers which
require especially large amounts of energy are temporarily cut back
or switched off. Heating systems in particular require a great deal of
energy .
If you notice, for example, that the heated seats* or the
heated rear window are not heating, they have been temporarily cut
back or switched off. These systems will be ava ilable again as soon as
the energy ba lance has been restored.
You will also notice that engine idle speed has been increased
slightly. This is normal and not a cause for concern. By increasing
eng ine id le speed the additional energy required is generated and the
battery is charged. •

____________________________________________ C_l_e _a_ n_ in--= g=-- a_n_ d_ p ,__r_o _t_ e_ c_ t _ io_ n __ _
Exhaust tail pipes
Road salt and other corrosive materials will damage the material in
the exhaust tai l pipes if they are not cleaned regularly . Do not clean
the tail pipes with wheel cleaner, paint po lish, chrome polish or other
abras ive cleaners. Clean the ta il pipes w it h ca r care products that are
suitable for sta inless steel.
Your authorized Audi dealer can provide cleaning products that have bee n tested and approved for your veh icle .•
Care of interior
Ap plies to ve hic le s: wit h MMI
MMI display
- Clean the MMI display with a sof t clean cloth and an LCD
cleaner .
The MMI display can be cleaned with a p rofessionally available "LCD
cleaner". The cloth should be slightly dampened with the cleaning
fluid to clean the d isp lay.
0 Note
T o avoid scratching the MMI disp lay, you should never clean it dry .•
Ap plies to ve hicle s: with MMI
MMI control console
- First clean the MMI control console with a brush to
remove dust from the housing.
- Then wipe the MMI control consol e with a clean, soft,
slightly damp cloth.
Safety first
The MMI control console should be cleaned with a brush first so that
no dirt is trapped be tween the bu tto ns and the ho using. We recom­
mend g iv ing the MMI co ntrol console a final w ipe with a cloth moist ­
ened with water and d ish washing detergent .
0 Note
To prevent damage, make sure that no fluid ever gets into the MM I
control console. •
Aluminum trim
Use only neutral-pH products to remove spots and deposits from
aluminum surfaces . Chrome care products and alkaline cleaners wi ll
attack alumi num surfaces and ca n damage them ove r time .
& WARNING
Always read and he ed all WARNIN GS and other information
~page 256. •
Fabrics and fabric coverings
Fabrics and fabr ic coverings (e.g. seats , door tr im panels, etc.) should
be cleaned at regular intervals with a vacuum cleaner . This removes
surface dirt particles which could become embedded in the fabric
through use . Steam cleaners should not be used, because the steam
tends to push the dirt deeper into the fabric and lock it there .
Normal clean ing
Genera lly, we recommend using a soft sponge or a lin t-free
microfiber cloth to the clean fabric . Brushes should only be used for
carpets and floor mats, since other fabric surfaces could be harmed
by brushes . _,,
Vehicle care Technical data

____________________________________________ C_l_e _a_ n_ i n--= g,___ a_n_ d----' p,___ r_o _t_ e_ c_ t_ i _o_ n __ _
The intensity of the color determines the visual characteristics and
appea rance. If the s urface of the leather has a typical natu ral look,
then the leather is a nappa leather that has been left in a relatively
natura l condition. This leather offers partic ularly good comfort and
breathes well. Fine veins, closed grains, insect b ites, sk in folds, and
subtle var iations in co lor remain visible. These character istics demon­
st rate that the mater ia l is nat ura l.
Natural nap pa leather is not covered by a color fin ish. It is therefore
mo re sensitive to soiling and we ar, which is some thi ng you need to
consider if children, animals or other factors mig ht prove to be partic­
ularly hard on the leather.
By contrast, leather types that a re cove red by a colo red fi nish layer
are more durab le . This has a positive effect on the leather's resistance
to wear and so ilin g in daily use. On the othe r hand, the typical charac­
teristics of natura l leather are barely or not apparent . However, this
does not mean that the leathe r itse lf is of inferio r quali ty.
Care and handling
Be cause of the exclusive na ture of t he types of leat her t ha t Audi uses
and their unique properties (such as sensitivity to oils, grease, soiling,
e tc. ), yo u will need to be somewhat c arefu l with these leat hers , a nd
a certain type of care is requ ired. For example, dark clothing mate­
r ia ls can dis co lor leather seats (especially if s uch cloth ing is damp and
was not dyed correctly). Dust and dirt particles in pores, folds, and
seams can have an ab rasive effect and can damage the leathe r
surface as well as weaken seams.
T he leather s ho ul d be cleaned regularly as needed . After having been
used for a relatively long time, your leather seats will a cquire a rich
aged f in ish. This is a characterist ic of natura l leather and a s ign of
t rue quality.
In order to maintain the value of this natural product over the life of
yo ur vehicle, you sho uld fo llow the recommendations below :
Safety first
0 Note
• To keep you r leat he r from b leach ing out, do not a llow it to be
exposed to bright s unlight for long periods of time . If yo u have to
leave t he veh icle parked o utside for long pe riods, cover the leather to
protect it from direct exposure to sunlight.
• Sharp objects on clot hing, such as z ippers, rivets or sha rp pieces
on belts can leave permanent scratches or scrape mar ks on the
surfa ce of the leathe r.
(I] Tips
• After ea ch t ime you clean the le athe r and at regular inte rvals, use
a leather preservat ive cream that contains UV-blockers and that
works into the leather . This cream will nourish and moistu rize the
leather, helping it to breathe and stay supp le. It also he lps to build up
a protect ive coa ting on the surface .
• Clean the leather every 2 -3 months, and clean any areas t hat get
so ile d.
• Remove fresh marks made by ballpoint pens, ink, lipstick, shoe
polish, etc. as soon as poss ible.
• Preserve the color of the leather as needed by using a special
c o lored leat he r car e cream to touch up a reas of uneven color. •
Applies to vehicles: w it h na tur al leat her
Cleaning and caring for leather upholstery
and trim
Natural leather requires s pecial care and attention .
Normal cleaning
-Clean soiled areas w it h a slightly moistened cotton or
woolen cloth.
Vehicle care Technical data

-~_T_ ir_e_ s_ a_ n_ d_ w_ h_e_ e_ ls _______________________________________________ _
& WARNING (conti nu ed )
• Tire s age even if they are not being used and can fail suddenly ,
especially at high speeds . Tires that are more than 6 year s old can
only be used in an emergency and then with special care and at low
s peed .
Glossary of tire and loading terminology
Accessory weight
means the combined we ight (in excess of those sta nda rd items which
may be rep lace d) of automatic transmission, power steering, power
bra kes, powe r w indows , power seats, radio, and heater, to the extent
that these items are avai lab le as factory- installed equipment
(w het he r i nsta lled or no t).
Aspect ratio
me ans the ratio of t he he ight to t he w id th of the tir e in percent .
Numbe rs of 55 o r lower indicate a low sidewa ll for improved steer ing
respo nse an d be tter overa ll handling on dry p avemen t.
Bead
means the part o f the tire that is made of stee l w ires , wrap ped o r
re in forced by ply cords and that is shaped to fit the rim.
Bead separation
means a brea kdown of the bon d between components in the bead .
Cord
means the st rands forming the plies in the tire.
& W ARNING (continued )
• Never mount used tire s on your vehicle if you are not sure of
their "previous hi story ." Old used tires may have been damaged
eventhoughthedamagecannotbeseenthatcanleadtosudden
tire failure and lo ss of vehicle control.
• If you notice unu sual vibration or if the vehicle pull s to one side
when driving, alway s stop as soon as it is safe to do so and check
the wheels and tires for damage. •
Cold tire inflation pressure
means the tire pressure recommended by the vehicle ma nufa cturer
for a tire of a des ignated size t hat has not been driven for more than
a couple of m iles ( kilomete rs) a t low speeds in the t hree ho ur period
before the tire pressure is measured or ad justed.
Curb weight
mea ns the weig ht of a motor vehicle wit h standard equ ipment
including the max imum cap aci ty of f ue l, oil, and coo lan t, air condi ­
tioning and additiona l weight of optional equipment.
Extra load tire
means a tire design to operate at higher loa ds and at higher inflation
pressures than the co rrespo nd ing standard tire. Extra load tires may
be identified as "XL", "xl", "EXTRA LOAD", or "RF" on the sidewal l.
Gross Axle Weight Rating ( "GAWR ")
means the load -ca rry ing capacity of a s ingle ax le system, measured at
t he t ire-grou nd inte rfaces .
Gross Vehicle Weight Rating ("GVWR")
means the max imum total loaded we ight of the vehicle .