2011 AUDI A5 COUPE warning

What do I do now? -________________ PfWII
Removing the spare tire
- Lift th e carg o floo r by the plas tic h andle ~ page 314,
fig . 2 20.
- H ook the hand le into t he luggage compa rtment weathe r
stri p.
- Tur n th e la rge screw~
page 314 , fig . 220 cou nter -clock-
w ise .
- Ta ke out the sp are t ire.
- U nho ok the c arg o flo or b efo re clos ing th e rear lid .
Securing the replaced tire
- Pla ce the w heel w it h t ire in t he spa re wheel we ll and
secu re t he wheel wit h the large sc rew.
- Unhook the c arg o floor before closing the re ar lid.
Using the spare tire (compact spare tire)
T he compact s pare tire is only inte nded for em er gen cie s until you can
reac h a repa ir sh op. R epl ace it as quickly as poss ible wit h a standar d
w he el a nd t ire.
Th ere are some rest rict io ns o n th e use of the compact s pare tire . The
compa ct spar e tir e has b een d esign ed spe cific ally f or your t ype of
vehicle. It must n ot be swa pped with a compact spare tire from
an other ty p e of vehi cle.
Snow chains
Fo r te chni cal re ason s, the use of snow ch ain s on th e compact s par e
t ire is not permitted .
I f y ou do h ave to dr ive wi th sno w chains an d a
front t ire fails, mount
t he spare wh eel w it h t ire instead of a rear tire. Ins tall the s now chai ns
on t he rear tire and use it to repla ce the defective fro nt tire .
Safety first
& WARNING
• Never use the spare tire if it is damaged or if it is worn down to
the tread wear indicators.
• If the spare tire is more than 6 years old, use it only in an emer ­
gency and with extreme caution and careful driving.
• The spare tire is intended only for temporary and short-term
use. It should be replaced as soon as possible with the normal
wheel and tire .
• After mounting the compact spare tire, the tire pressure must
be checked as soon as possible. The tire pressure of the compact
spare tire must be 4.2 bar; otherwise, you risk having an accident.
• Do not drive faster than 50 mph (80 km/h) . You risk having an
accident.
• Avoid full-throttle acceleration, heavy braking, and fast
cornering. You risk having an accident.
• Never drive using more than one spare wheel and tire. You risk
having an accident.
• Normal summer or winter tires must not be mounted on the
compact spare wheel rim.
• For technical reasons, the use of tire chains on the spare tire is
not permitted. If it is necessary to drive with tire chains, the spare
wheel must be mounted on the front axle in the event of a flat in
a rear tire. The newly available front wheel must then be installed
in place of the rear wheel with the flat tire . Installing the tire
chain before mounting the wheel and tire is recommended.
• Loose items in the passenger compartment can cause serious
personal injury during hard braking or in an accident.
- Never store the inflatable spare tire or jack and tool s in the
passenger compartment.
- Always store all jacking equipment, tools, and the inflatable spare tire in the luggage compartment.
- Tighten the knurled retaining screw for the inflatable spare
tire securely. •
Vehicle care Do-it-yourself service Technical data

lffll.___W __ h_a_ t_ d_ o_ I_ d_o_ n_ o_w _ ? _____________________________________________ _
Changing a wheel
Before changing a wheel
Observe the following precautions for your own and your
passenger's safety when changing a wheel.
- After you experience a tire failure, pull the car well away
from moving traffic and try to reach
level ground before
you stop
~ & .
- All passengers should
leave the car and move to a safe
location (for instance, behind the guardrail)~& .
- Engage the
parking brake to prevent your vehicle from
rolling unintentionally~ &.
- Shift into
1st gear on vehicles with manual transmission,
or move the
selector lever to the P position on vehicles
with automatic transmission*.
- If you are towing a trailer: unhitch the trailer from your vehicle.
- Take the
jack~ page 314 and the spare tire~ page 314
out of the luggage compartment.
& WARNING
You or your passengers could be injured while changing a wheel if
you do not follow these safety precautions:
• If you have a flat tire, move a safe distance off the road. Turn
off the engine, turn the emergency flashers on and use other
warning devices to alert other motorists.
• Make sure that passengers wait in a safe place away from the
vehicle and well away from the road and traffic.
& WARNING (continued)
• To help prevent the vehicle from moving suddenly and possibly
slipping off the jack, always fully set the parking brake and block
the wheel diagonally opposite the wheel being changed with the
folding chocks or other objects. When one front wheel is lifted off
the ground, placing the Automatic Transmission in "P" (Park) will
not prevent the vehicle from moving.
• Before you change a wheel, be sure the ground is level and
firm. If necessary, use a sturdy board under the jack.
• After installing the inflatable spare tire, make sure that you
replace the flat tire/wheel in its storage area properly and tighten
the knurled retaining screw securely.
0 Note
If you are changing the wheel on a steep incline, use a rock or simila r
object to block the opposite wheel to prevent the vehicle from
moving.
[ i] Tips
Obey all laws. •
Changing a wheel
When you change a wheel, follow the sequence described
below step-by-step and in exactly that order.
1. Remove the decorative wheel cover* or the wheel bolt
caps* .
For more details see also~ page 317, "Decorative
wheel covers" or~
page 318, "Wheels with wheel bolt
caps".
2. Loosen the
wheel bolts~ page 318. .,_

_____________________________________________ W __ h_a _ t_ d_o_ I_ d _ o_ n_o_ w_ ? _ ___.ffl'I
3. Locate the proper mounting point for the jack and align
the jack below that point=>
page 319.
4. Lift the car with the jack=> page 319.
5. Remove the wheel with the flat tire and then install the
spare tire => page 320 .
6. Tighten all wheel bolts lightly.
7.
Lower the vehicle with the jack.
8. Use the wheel bolt wrench and
firmly tighten all wheel
bolts in a crisscross pattern=>
page 318.
9. Replace the decorative wheel cover* or the wheel bolt
caps*.
& WARNING
Always read and follow all WARNINGS and information=> & in
"Raising the vehicle" on
page 319 and => page 322. •
After changing a wheel
A wheel change is not complete without the doing the
following.
- Store and secure the wheel you replaced in the spare
wheel well .
Replace the tools and the jack in their proper location.
- Check the
tire pressure of the spare tire as soon as
possible.
- As soon as possible , have the
tightening torques on all
wheel bolts checked with a torque wrench. The correct
tightening torque is 90 ft lbs. (120 Nm).
Vehicle OP-eration
-Have the flat tire replaced as soon as possible.
[ i] Tips
• If you notice that the wheel bolts are corroded and difficult to turn
while changing a tire, they should be replaced before you check the tightening torque.
• Drive at reduced speed until you have the tightening torques
checked. •
Applies to ve hicles : w ith deco rative wheel cove rs
Decorative wheel covers
The decorative wheel covers must be removed first to
access the wheel bolts.
Removing
Fig. 221 Changing a
wheel: removing the
wheel cover
- Insert the hook provided with the vehicle tool kit in the
hole in the hub.
- Pull off the
decorative wheel cover=> fig. 221. •
Vehicle care Do-it-yourself service iTechnical data

-L--....:..:W:..:..; h:..:.:: a:..:t :... d.:.:..: o:.:...:. I..;d:.:...:. o....:..: n:..:o :...w:..:..:. ? ___________________________________________ _
Applies to veh icles : w ith wheel bolts w ith caps
Wheels with wheel bolt caps
The caps must be removed first from the wheel bolts
before the bolts can be unscrewed .
Removing
Fig. 222 Changing a
wheel: removing the
wheel bolt caps
-Push the plastic clip provided with the vehicle tool kit over
the wheel bolt cap until it engages.
- Pull on the
plastic clip to remove the cap~ fig. 222 .
Refitting
-Place the caps over the wheel bolts and push them back
on.
The caps are to protect and keep the wheel bo lts clean. •
Loosening and tightening the wheel bolts
The wheel bolts must be loosened before raising the
vehicle .
Loosening
Fig. 223 Changing a
wheel: loosening the
wheel bo lts
- Install the wheel bolt wrench over the wheel bolt and
push it down as far as it will go .
- Take tight hold of the
end of the wrench handle and turn
the wheel bolts
counter-clockwise about one single turn
in the direction of arrow~ fig. 223.
Tightening
-Install the wheel bolt wrench over the wheel bolt and
push it down as far as it will go.
- Take tight hold of the
end of the wrench handle and turn
each wheel bolt
clockwise until it is seated .
& WARNING
• Do not use force or hurry when changing a wheel -you can
cause the vehicle to slip off the jack and cause seriou s personal
inju ries.

_____________________________________________ W __ h....:a_ t ___ d_o ___ I_ d_o :.....:.. n.:..o::.. w.:....:.. ?------J-
& WARNING (continued)
• Do not loosen the wheel bolts more than one turn before you
raise the vehicle with the jack. -You risk an injury.
(I) Tips
• Never use the hexagonal socket in the handle of the screwdriver to
loosen o r tighten the wheel bolts .
• If a wheel bolt is very tight, you may find it easier to loosen by
carefully pushing down on the end of th e wheel bolt wrench with
one
foot only .
As you do so, hold on to the car to keep your balance and
take ca re not to slip .•
Raising the vehicle
The vehicle must be li~ed with the jack first before the
wheel can be removed.
•
Fig. 224 Changing a
wheel: mounting
points for the jack
Vehicle OP-eration
Fig. 225 Close-up:
proper positioning of
jack
The location of the jack point is indicated by an indentation
on the underside of the vehicle=> fig. 224.
- Activate the
parking brake to prevent the vehicle from
rolling unintentionally.
- Shift into
1st gear on vehicles with manual transmission
or move the selector lever to the
P position on vehicles
with automatic transmission*.
- Find the
lifting point in the sill that is closest to the faulty
wheel => fig. 224.
Turn the handwheel on the
vehicle jack until the jaw
=> fig . 225 @ covers the
notch on the vehicle.
- Align the vehicle jack so the jaw@ covers the notch and
the base plate @ is flat on the floor. The base plate @
must be
vertical under the lifting point@.
- Install the rod on the vehicle jack: Insert the rod into the
opening on the handwheel. Turn the rod left or right to
secure it.
- Continue raising the jack with the rod until the wheel lifts
off the ground slightly. ..,_
Vehicle care Do-it-yourself service iTechnical data

lffl!l.,___W __ h_a_ t_ d_ o_ I_ d_o_ n_ o_w _ ? _____________________________________________ _
Only position the veh icle jack at the designated points=> page 319,
fig . 224 . Th ere i s ex act ly
one loc ation for each whee l. Do not position
the jac k in any othe r locations .
Soft ground under the jack can cause the vehicle to slip
off the jack.
Alw ays p lac e the j ack on firm ground . U se a fla t, stab le s uppor t if
necessary. Use a non -s li p surface s uch as a ru bber mat on a slippery
surface such as ti le.
& WARNING
• You or your passengers could be injured while changing a
wheel if you do not follow these safety precautions :
- Positioning the jack under the vehicle at any other place than
those indicated above may damage the vehicle or may result in personal injuries.
- A soft or unstable surface under the jack may cause the
vehicle to slip
off the jack. Always provide a firm base for the
jack on the ground.
If necessary, use a sturdy board under the
jack.
- On hard, slippery surface (such as tiles) use a rubber mat or
similar to prevent the jack from slipping.
• To help prevent injury to yourself and your passengers: -Do not raise the vehicle until you are sure the jack is securely
engaged.
- Passengers must not remain in the vehicle when it is jacked
up .
- Make sure that passengers wait in a safe place away from the
vehicle and well away from the road and traffic.
- Make sure jack position is correct, adjust as necessary and
then continue to raise the jack. •
Taking the wheel off/installing the spare
tire
Follow these instr u ction s step- by -s tep for chan ging th e
w heel .
Fig. 226 Changing a
wheel : using the
s crewdriver handle
( with the blade
removed ) to turn the
bolts
Fig. 227 Changing a
whee l: alignment pin
in side the top hole
Aft er yo u have L oosened a ll w hee l bolts and r aise d the v ehicle
off th e ground, remo ve and rep lace t he whe el as fo llows :
Removing the wheel
- Remove the top most w hee l b olt comp letely with the
hexagonal socket in the screwd river handl e (vehicle too l
kit )
~ fig. 2 26 and set i t aside on a clean surf ace . .._

-What do I do now? Pffl...__ ______________ _
Notes on wheel changing
Please read the in formation => page 303, "New t ires and replacing
t ires and wheel s" i f yo u ar e going t o use a sp are tir e w hich is differe nt
from t he tires on yo ur vehicle.
After you c hange a ti re:
• Check the tire pressure on the spare immediately after installa·
tion.
• Have the wheel bolt tightening torque checked with a torque
wrench as soon as possible by your authorized Audi dealer or a qual· ified workshop.
• With steel and alloy wheel rims , the wheel bolts are correctly
tightened at a torque of 90 ft lbs. (120 Nm).
• If you notice that the wheel bolts are corroded and difficult to
turn while changing a tire, they should be replaced before you check
the tightening torque .
• Replace the flat tire with a new one and have it installed on your
vehicle as soon as possible. Remount the wheel cover.
Until then, drive with extra care and at reduced speeds.
& WARNING
• If you are going to equip your vehicle with tire s or rims which
differ from those which were factory in stalled, then be sure to
read the information =>
page 303, "New tires and replacing tires
and wheels".
• Always make sure the damaged wheel or even a flat tire and
the jack and tool kit are properly secured in the luggage compart­
ment and are not loose in the passenger compartment .
• In an accident or sudden maneuver they could fly forward,
injuring anyone in the vehicle .
• Always store damaged wheel , ja ck and tools securely in the
luggage compartment. Otherwise, in an accident or sudden
& WARNING (c on tinued )
maneuver they could fly forward , causing injury to passengers in
the vehicle.
0 Note
Do not use commerci ally ava ilable tire se alants . O th erwi se, the ele c­
trical components of the t ire pressure monitoring system* w ill no
longer wor k properly and the se nsor for the tire pressure moni to ring
system* wi ll have to be rep laced by a q ua lified wor kshop .•

____________________________________________ ..:.F..:u::.:s:::.:e::.:::s_:a::.:n'...:.::d'.....!:::b~u~l~b~s !.__J-
Fuses and bulbs
Fuses
Replacing a fuse
Fuses that have blown will have metal strips that have
burned through .
Fig. 228 Left cockpit:
fuse panel cover
The fuses are located at the front left and right of the cockpit
and behind the trim on the right side of the luggage compart ­
ment .
- Turn off the ignition and the affected electrical
consumers.
- Check the following table to see which fuse belongs to the
consumer.
- Remove the appropriate cover => fig. 228 or =>
page 2 73,
fig. 201.
Vehicle OP-eration
- To remove the purple plastic clip if necessary 4
), hold onto
it at the small side and pull it out of the fuse panel
~ page 324, fig. 229 .
- Remove the clamp from the rear side of the fuse cover
~ fig. 228.
- Remove the fuse using the clamp and replace the blown
fuse with an identical new one.
& WARNING
Do not repair fuses and never replace a blown fuse with one that
has a higher amp rating. This can cause damage to the electrical
system and a fire.
0 Note
If a new fuse burns out again after shortly have you have installed it,
have the electrical system checked by your authori zed Audi dealer.
[I] Tips
• The following table does not list fuse locations that are not used .
• Some of the equipment items listed are optional or only available
on certain model configurations.
• The crank in the cover is used for emergency operation of the
sunroof* .•
4
> You ca n dis p ose of the plastic cl ip after removi ng it.
Vehicle care Do-it-yourself service iTechnical data