2011 AUDI A5 COUPE reset

Driver information display
& WARNING
Alwa ys observe the posted speed limits and adjust your speed to
suit pre vailing road, traffi c and weather condition s. Never drive
your vehicle fa ster than the maximum speed rating of the tires
installed .•
Speed warning system
Overview
Th e speed war ning syst em helps you to keep your d riv ing
speed below a set speed limit.
Th e speed warning system warns if the dr iver exceeds a prev iously
sto red ma ximum speed. A warning tone will sound as soon as the
vehicle speed exceeds the set speed by about 3 mph (3 km/h). At the
same time, a warning symbol appears in t he di sp lay. The symbo l's
appea rance might be different in some models .
T he speed warn ing system has two warnin g thresho lds th at f unctio n
independently of eac h oth er and that have somewhat diffe rent
purposes:
Speed warning 1
Yo u ca n use speed war ning 1 to set the maximum speed wh ile you a re
driving. This setting will remain in effect until you turn off t he igni­
tion , assuming t hat you have not changed or reset t he setting .
T he speed w arnin g symbo l
0 (USA mo dels) /8 (Canada mode ls) in
the warning 1 display appears when you exceed the maximum speed .
It goes out whe n the speed falls be low the stored max imum s peed.
T he speed warning symbo l will a lso go out if the speed
exceeds the
stored maximum s peed by more than about 2 5 mph ( 40 km/h) fo r at
least 10 seconds . The stored maximum speed is deleted.
Speed warning 2
Storing warn ing 2 is recommended if you always want to be reminded
of a ce rta in speed, fo r example when yo u are traveling in a country
that has a general maxim um speed limit, or if you do not want to
exceed a specified speed for win ter tires .
The speed warn ing 2 symbol,
8. ( U SA models)/ 8. (Canada models)
appea rs in the d isp lay w hen you exceed the store d speed limi t. U nlike
warning 1, it will not go o ut until the vehicle speed drops be low the
sto red speed limi t.
Sett ing speed warn ing 2
=;, page 31 .
[I] Tips
Even thoug h your vehicle is eq uipped with a speed warning system,
you should st ill watch the speedometer to make sure you are not
dr iv ing fast er th an the speed lim it. •
Speed warning 1: setting a speed limit
Wa rnin g thresho ld 1 is set by the [ SE T] button.
Storing the maximum speed
- Drive at the desire d max imum speed .
Fig. 23 SET butt on in
the in strument clu ste r

- Press the [S ETI button in the instrument panel display
~ page 30, fig. 23 for 1 second.
Resetting the maximum speed
- Drive the veh icle at a speed of at least 3 mph (5 km/ h)
- Press the
[S ET ] button for more than 2 seconds .
The speed warning symbo l E, (USA models)/8 (Canada models) will
appear b riefly in the display when yo u release the
I SETI button to
indicate that the maximum speed has been stored s uccessfully.
T he maxim um speed rema ins sto red until it is changed by p ressing
the
[ SET I button again briefly or until it is de leted by a lengthy push
on the button. •
Speed warning 2: setting a speed limit
The radio or MM I* contro l unit is us ed to set, change or
delete warning threshold 2.
- Select: Funct ion button [CAR I> Instrument cluster >
Speed warning .
Warning thresho ld 2 can be set in the speed range starting from 20
mph to lS0 mph (30 km/h to 240 km/h) . Settings can each be
adjusted in interva ls of 6 mph (10 km/h). •
Auto Check Control
Introduction
The Auto-Check control monitors the function of certain vehicle
features and components . It simp ly makes su re these features and
components are work ing properly. The Auto-Check control works as
long as the ignition is on, as we ll as whenever the vehicle is driven.
Controls and equip ­
ment Safety first
Dri
ver information display
If a component is malfunctioning or if the need for an urgent repair
has bee n de tected, t his will appea r in t he inst rument clus ter display.
You will also hear an audible warn ing tone. The d isp lays are color
co ded in either red or yellow depending on their level of priority.
A red symbol means Danger, a yellow symbo l ind icates Warning . In
certain situations, information message for the driver appear in addi­
ti on to t he red and ye llow symbo ls .
Function test: automatic transmission*
T he Auto-Check Contro l w ill a utomat ically perfo rm a test each time
you switch on the ignit ion. W ith the selector lever in
P or N , the
following message appears in t he d isp lay:
When stationary apply foot brak e while selecting gear .
When you a select a different gear (for example:
R , D , etc.), the
message w ill disappea r and the Auto-Check function is d isplayed .
If there is a ma lfunction, then the malfunct ion message will appear
abou t 15 seconds a fter you st art the vehicle. At the s ame time you
will hear a warning tone. •
Driver information messages
Driv e r information messa ges are sho wn in the instru­
ment cluster display in addition to symb ols.
Fig. 24 In strum ent
clu ster: SET button
~
Vehicle care Technical data

Warm and cold
Applie s to vehicles : wi th del uxe automatic climate contro l
Setting the temperature
Fig. 97 Temperature
setting regulator
- Rotate the regulator to the left to reduce the tempera-
ture, orto the right to increase the temperature~ fig. 97.
The selected temperature appears on the climate contro l display. The
temperature setting will also appear for a few seconds in the radio or
MMI* display. •
Applie s to vehicles : wit h del uxe automatic cl imate contro l
FanOO
The outomo6colly preset fan speed con be reduced or
increased .
-Press the IS!?] button .
Fig. 98 Fan button
and regulator
- Rotate the regulator to set the desired fan speed (air
volume).
We recommend always running the fan at a low speed when driving
slowly.
To prevent polluted outside air (smell) from entering the interior of
t he vehicle, switch to
recirculation mode by pressing the button 1¢e:>J.
When the radio or MMI* is turned on, the fan speed setting appears
for a few seconds on the screen.
[1] Tips
• It is possible that the fan speed may change automatically. This
occurs to ensure that the desired temperature setting is reached as
quickly as possible .
• The fan speed cannot be regulated separately for the driver and
front passenger. •

Appli es to veh icles: wi th del uxe auto matic c limate contro l
Recirculation mode (~I
The recirculation mode prevents polluted outside air
from entering the vehicle interior.
A ctiva ting
- Press the button [cD] => &.
De activating
- Press the button [cD] again, or
- press the
[AUTO] button.
In recirculation mode, air is drawn from the vehicle interior, filtered
and recirculated . We recommend selecting recirculation mode under
the following conditions:
When driving through a tunnel or in a traffic jam so that exhaust
fumes and odors cannot enter the vehicle interior.
& WARNING
Y ou sh ould not u se the recirc ulati on m ode f or a n exte nded p erio d
si nce no fre sh air is draw n in . With t he air-condi tioning swit ched
o ff, the windows ca n fo g up, whi ch in creases the risk of an
ac cident !•
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
Warm and cold
App lies to veh icl es: wit h delux e a utoma tic clim ate cont rol
Air distribution [in]
The automatically preset air distribution can be changed.
- Press the [ ·ial button.
Fig. 99 Air distribu­
tion button a nd reg u­
lator
- Rotate the regulator to the desired setting .
You can adjust the air distr ibut ion so that air flows from specific
vents. In position
;J air flows only to the windows, in position :,0, it
flows to the drive r or passenger, and in position
!,J it f lows to the
footwell. There are additional combinations available to adjust air
distribution as needed .
To regulate air distribution automatically, switch to
! AU TO].
When the radio or MMI" is turned on, the air distribution setting
appea rs for a few seconds on the screen. •
Ap plies to v eh icles: with de luxe automat ic cli mate control
Defrost [@]
The windshield and side windows are defrosted or cleared
of condensation as quickly as possible .
-Press the button [@)to turn on the defroster .
Vehicle care Do-it-yourselt service Technical data

_________________________________________________ W_ a_ r_m _ a_ n_d_ c_ o_ ld _ ___.llfflll
App lies to veh icles : wi th Delu xe aut omat ic climate contro l plus
Fan ~
The automatically preset fan speed can be reduced or
increased .
-Press the[~] button=> fig . 102.
Fi g. 102 Fa n but ton
and re g ul ator
- Rotate the regulator to set the des ired fan speed (air
volume) .
The clima te control system automatically regula tes fan speed based
on the interior temperature . You can adjust the volume of a ir
produced by the fan to your own requirements.
W hen the MMI display is tur ned on, t he fan speed setting appears for
a few seconds on the screen .
[ i J Tips
• It is possible that the fan speed may change automatically . This
occurs to ens ure that the desired temperature set ting is reached as
quickly as possible.
• T he fan speed cannot be reg ulated separately for the dr ive r and
front passenger .•
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
Applies to vehicles : with Deluxe au tomat ic clima te cont ro l plus
Recirculation mode[~)
The recirculation mode prevents polluted outside air
from entering the vehicle interior.
Turning on recirculation mode
- Press the [a;:, ]=> & button .
Turning off recirculation mode
-Press the~ button again, or
press the
[AU TO] button.
In recirculation mode, ai r is drawn from the vehicle interior, filtered
and rec irc ulated . We recommend selecting rec irculation mode under
the following conditions:
Whe n driving throug h a tunnel or i n a t raffic jam so that exhaust
fumes and odors cannot enter the veh icle interior.
& WARNING
You should not u se the recirculation mode f or an exte nded period
sinc e no fre sh a ir i s drawn in . With the air- conditioning switch ed
off, the windows can fog up , which increase s the risk of an
a cci dent! •
Vehicle care Do-it-yourselt service iTechnical data

ffl..__w __ a _r _m __ a_n _ d_ c_ o_ ld ________________________________________________ _
Applies to veh icles : w ith Deluxe automatic climate contro l p lus
Air distribution [~]
The automatically preset air distribution can be changed.
- Press the[~] button=> fig. 103.
Fig. 103 Air distribu ­
tion button and regu­
lator
- Rotate the regulator to the desired setting.
You can adjust the air distribution so that air flows from specific
vents . In position
;J air flows only to the windows, in position :J, it
flows to the driver or passenger, and in position
!,O it flows to the
footwell. There are additional combinations availab le to adjust air
distribution as needed.
To regulate air distribution automatically , switch to
[AUTO] .
When the MMI display is turned on, the air distribution setting
appears for a few seconds on the screen. •
Applies to vehicles: w ith De luxe automatic climate control plus
Defrost [@]
The windshield and side windows are defrosted or cleared
of condensation as quickly as possible.
- Press the[@] button to turn on the defroster. -
Press the[@] button again, or press the (AUTO
I button to
turn it off.
T emperat ure is controlled automatically. The maximum amount of
air flows mainly from the vents below the windshield.
Pressing the
I@ ] button switches off recirculation mode. •
Applies to vehicl es: w ith Deluxe automat ic clima te control plus
Rear window defogger [ Qiil ]
The rear window defogger clears the rear window of
condensation.
- Press the [lllil] button to turn the rear window defogger on
and off .
The rear window defogger works only when the engine is running. The
indicator light in the button illuminates when the rear wind ow
defogger is on.
The rear window defogger is switched off automatically after 10 to
20 minutes, depending on the outside temperature.
The rear window defogger can be turned on permanently by pressing
the
[Qlil] button for more than two seconds. This remains stored until
the ign it ion is switched off. A rear window defogger that was
switched on also remains stored for 15 minutes after the ignition is
switched off.
If the engine is restarted within these 15 minutes, the rear window
defogger is activated for 10 to 20 minutes, depending on outside
temperature. When a vehicle is parked for a short time, the rear
window defogger does not need to be manually activated again. •

IIII..__A_ d_a_ p,__ t_iv _ e_ c_r_ u _i _ s _e _ c_o _n _ t_ r_ o_ l ___________________________________________ _
Driving pro­
gram
Dis tance 1
Distance 2
Distance 3
& WARNING
dynamic
1
2
2
3
standard
2
3
3
4
comfort
3
4
4
5
-
When setting the distance, the dri ver is responsible for adhering
to the respect ive national and country -specific regulations .
• Following other vehicles too closely increase s the risk of colli­
sions and serious personal injury.
• Setting short distance s to the traffic ahead reduce s the time
and d istanc e av ailable to bring your vehicle to a safe stop and
makes it even more neces sary to pay clo se attention to traffi c.
• Always use good judgment and select a safe following distance
for the traffic , road and weather condition s.
(I] Tips
The d istance setting is reset to the factory default DISTANCE 3 the
next time the ignition is t urned on .•
Driver information
Ap plies to veh icles: w it h ad aptiv e c ru is e co ntro l
Displays in the instrument cluster
Depending on the driving situation, driver information is
displayed in the instrument cluster.
Fig. 11 9 Ove rv iew i nstrum ent clu ste r
© Speedomete r and indicator light disp lay
@ Display in the ins trument cluste r
© Message in the instr ument cluster disp lay
© Speedometer and indicator light d isplay
Important informa tion concerning vehicle ope ration wi th adap tive
cruise control is shown in display area@. The desired speed you set
is indica ted in the speedome ter (L ED ligh ts aro und the edge).
T he indicator lights show whether the system has detected a veh icle
traveling ahead . .,,.

____________________________________________ A_ d_ a.._p _t_ i_ v _e_ c_r_u _ i_ s _e_ c_o_ n_ t_r _o _l __ _
@ Display in the instrument cluster
In disp lay area @ information from the navi gation system * and the
tr ip computer is displayed in add it ion to informa tion about adaptive
c ruise contro l.
You can sele ct among the differe nt info rmatio n by repeated b rief
taps on the
I RESET! button on the winds hield w iper lever => page 26,
"Operat io n".
© Status indicator
Th e info rmation i n area © is no t disp layed per manently. Infor mat ion
is d isplayed o nly if yo u set or c hange the speed setting, change the
ti me in terva l, when messages a re displayed or if the ad apt ive cru ise
cont rol is turned off for safety reasons. •
Appli es to vehicles : w ith a daptive cruise c on tro l
Speedometer and indicator light display
----
- -
- -
@ ®
Desired speed
- -
--
Fig . 120 I nstru ment
cl uste r: Indicator light
T he desired speed set by the driver is displayed by a red LED in the LED
disp lay in the spee dometer.
If the desi red s peed was set be twee n two lines o n the speedo mete r
using the
[ SET J button, the two closest light diodes will come on
=>
page 12 8, fig. 119.
Controls and equip ­
ment Safety first
T
he system allows only speeds from 20 to 95 mph (30 to 150 km/ h)
t o be se t. T his spee d range is f aint ly ill um inat ed in t he s pee dome ter
(LED lights) .
Indicator lights (symbols)
• © Open road: The indicator light shows t hat adaptive cruise
co ntrol is a ctive and t hat no objec t is ahe ad of the vehi cle. A sto red
speed req uested is maintained.
• @
Driving in traffic : The indicator l igh t ind icates th at an object
has been detected traveling in front . Your speed is ad justed according
t o the spee d of t he vehicle in front. The adaptive c ruise con trol accel­
erates and bra kes au tomatically w it hin the system's operat io n
parame ters.
• ©
Driver intervention prompt : The red flashing warning light
me ans
Request for driver to as sume control. You as the drive r m ust
slow t he ve hicle w ith the foot brake . The symbo l tells yo u that the
adaptive cruise contro l is not able to s low the vehicle down enough to
keep a enough distance to the vehicle in front o f you. An war ning tone
wi ll also so und when the symbol ap pears. Fo r more informat ion
abou t the driver intervent ion prompt=>
page 132 .
W Tips
• If you use the ac cele rator to go fa ster than the speed of the object
ahead of you, the
driver intervention prompt will not be accompa ­
nied by a war ning signal.
• If the speed you p reviously set is exceeded, the ind icator light in
t he s peedometer w ill swit ch off .•
Vehicle care Technical data